AUTOMATIC TRANSAXLE UNIT > INSPECTION |
| 1. INSPECT TRANSMISSION OIL CLEANER MAGNET |
Examine particles in the automatic transaxle oil pan sub-assembly.
![]() |
Collect any steel chips with the removed magnets. Look carefully at the chips and particles in the automatic transaxle oil pan sub-assembly and on the transmission oil cleaner magnets to see the type of wear which might be found in the automatic transaxle assembly.
| Steel (magnetic) | Brass (non-magnetic) |
| Bearing, gear and plate wear | Bushing wear |
| 2. INSPECT INPUT SHAFT END PLAY |
![]() |
Using a dial indicator, measure the input shaft end play.
| 3. INSPECT INTERMEDIATE SHAFT END PLAY |
![]() |
Clean the contact surfaces of the transaxle case sub-assembly and rear transaxle cover sub-assembly.
As shown in the illustration, place a straightedge on the multiple direct clutch drum and measure the distance between the transaxle case sub-assembly and the straightedge using a vernier caliper (Dimension A).
| *a | Dimension A |
![]() |
Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).
| *a | Dimension B |
Calculate the end play value using the following formula:
End play = Dimension B - Dimension A - Thrust needle roller bearing thickness
| 4. INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY |
![]() |
Using a caliper gauge, measure the inside diameter of the bushings of the planetary sun gear.
| 5. INSPECT REAR PLANETARY SUN GEAR ASSEMBLY |
![]() |
Using a caliper gauge, measure the inside diameter of the bushing of the rear planetary sun gear sub-assembly.
| 6. INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the clearance between the underdrive planetary gear and the pinion gear at 4 points.
| 7. INSPECT ONE-WAY CLUTCH ASSEMBLY |
![]() |
Temporarily install the one-way clutch assembly to the planetary ring gear.
| *1 | Planetary Ring Gear |
| *2 | One-way Clutch Assembly |
| *a | Free |
| *b | Lock |
Make sure that the one-way clutch assembly turns freely counterclockwise and locks when turned clockwise.
If the one-way clutch assembly does not operate normally, replace it.
| 8. INSPECT NO. 1 BRAKE DISC |
![]() |
Check if the contact surfaces of the discs, plates and flange are worn or burnt.
| 9. INSPECT NO. 2 BRAKE DISC |
![]() |
Check if the contact surfaces of the discs, plates and flange are worn or burnt.
| 10. INSPECT NO. 3 BRAKE DISC |
![]() |
Check if the contact surfaces of the discs, plates and flanges are worn or burnt.
| 11. INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the 3 2nd brake piston return springs including the spring seats.
| 12. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the 1st and reverse brake return spring together with the spring seat.
| 13. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the No. 3 brake piston return spring together with the spring seat.
| 14. INSPECT CLEARANCE OF NO. 1 BRAKE |
![]() |
Using a dial indicator, measure the clearance of the No. 1 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
| Mark | Thickness [mm (in.)] |
| 30 | 3.0 (0.118) |
| 31 | 3.1 (0.122) |
| 32 | 3.2 (0.126) |
| 33 | 3.3 (0.130) |
| 34 | 3.4 (0.134) |
| 35 | 3.5 (0.138) |
| 15. INSPECT CLEARANCE OF NO. 2 BRAKE |
![]() |
Using a dial indicator, measure the clearance of the No. 2 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
| Mark | Thickness [mm (in.)] |
| 40 | 4.0 (0.157) |
| 41 | 4.1 (0.161) |
| 42 | 4.2 (0.165) |
| 43 | 4.3 (0.169) |
| 44 | 4.4 (0.173) |
| 16. INSPECT CLEARANCE OF NO. 3 BRAKE |
![]() |
Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension A) while a load of 500 N (51 kgf, 112.4 lbf) is being applied to the flange.
| *1 | Front Oil Pump Assembly |
| *2 | No. 3 Brake |
| *a | Dimension A |
| *b | Dimension B |
| *c | Contact Surface of Front Oil Pump Assembly |
Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).
Calculate the clearance value using the following formula:
Clearance = Dimension B - Dimension A - Flange Thickness
| Mark | Thickness [mm (in.)] |
| 38 | 3.80 (0.150) |
| 39 | 3.90 (0.154) |
| 40 | 4.00 (0.157) |
| 41 | 4.10 (0.161) |
| 42 | 4.20 (0.165) |
| 43 | 4.30 (0.169) |
| 17. INSPECT CLEARANCE OF NO. 1 CLUTCH |
![]() |
Install the direct multiple disc clutch assembly onto the rear transaxle cover sub-assembly.
Check that the piston moves when compressed air (200 kPa, 2.0 kgf/cm2, 29 psi) is applied to the oil hole.
![]() |
Using a feeler gauge, measure the No. 1 clutch pack clearance.
| *1 | Feeler Gauge |
| 18. INSPECT CLEARANCE OF NO. 2 CLUTCH |
![]() |
Install the direct multiple disc clutch assembly onto the rear transaxle cover sub-assembly.
Using a dial indicator, measure the No. 2 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).