Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (for 2GR-FE)

POWER STEERING SYSTEM (for 2GR-FE) > TERMINALS OF ECU

for Preparation Click here



CHECK POWER STEERING ECU ASSEMBLY

C239855E05


Text in Illustration 
*a
Component without harness connected
(Power Steering ECU Assembly)
-
-
  1. Measure the voltage and resistance according to the value(s) in the table below.

    NOTICE:
    When the P/S warning light is illuminated due to a malfunction, the fail-safe function may cause the voltage of the power steering ECU assembly terminals to become 0 V.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    j3-1 (IG) - j2-2 (PGND)
    R - B
    IG power source
    Engine switch on (IG)
    9 to 16 V
    j3-4 (CANH) - j3-8 (CANL)
    Y - SB
    CAN communication line
    Engine switch off
    54 to 69 Ω
    j3-5 (TS) - j2-2 (PGND)
    O - B
    Terminal TS of DLC3
    Always
    9 to 16 V
    b-1 (TRQG) - Body ground
    B - Body ground
    Torque sensor ground
    Always
    Below 1 Ω
    b-2 (TRQ2) - b-1 (TRQG)
    Y - B
    Torque sensor signal
    Engine running
    Steering wheel not being turned (without load)
    2.3 to 2.7 V
    Engine running
    Steering wheel being turned to right with vehicle stopped
    0.3 to 2.5 V
    Engine running
    Steering wheel being turned to left with vehicle stopped
    2.5 to 4.7 V
    b-3 (TRQV) - b-1 (TRQG)
    R - B
    Torque sensor voltage source
    Engine switch on (IG)
    8.5 to 10.5 V
    b-5 (TRQF) - j2-2 (PGND)
    G - B
    Torque sensor reference voltage
    Engine switch on (IG)
    3.35 to 3.37 V
    b-7 (TRQ1) - b-1 (TRQG)
    W - B
    Torque sensor signal
    Engine running
    Steering wheel not being turned (without load)
    2.3 to 2.7 V
    Engine running
    Steering wheel being turned to right with vehicle stopped
    2.5 to 4.7 V
    Engine running
    Steering wheel being turned to left with vehicle stopped
    0.3 to 2.5 V
    c-1 (RZCS2) - j2-2 (PGND)
    L - B
    Rotation angle sensor COS aspect output signal
    Engine running
    Steering wheel turned
    0.68 to 4.42 V
    c-2 (RZV2) - j2-2 (PGND)
    R - B
    Rotation angle sensor excitation output signal
    Engine running
    Steering wheel turned
    0.68 to 4.42 V
    c-3 (RZSN2) - j2-2 (PGND)
    Y - B
    Rotation angle sensor SIN aspect output signal
    Engine running
    Steering wheel turned
    0.68 to 4.42 V
    c-5 (RZCS1) - j2-2 (PGND)
    L - B
    Rotation angle sensor COS aspect output signal
    Engine running
    Steering wheel turned
    0.68 to 4.42 V
    c-6 (RZV1) - j2-2 (PGND)
    R - B
    Rotation angle sensor excitation output signal
    Engine running
    Steering wheel turned
    0.68 to 4.42 V
    c-7 (RZSN1) - j2-2 (PGND)
    Y - B
    Rotation angle sensor SIN aspect output signal
    Engine running
    Steering wheel turned
    0.68 to 4.42 V
    j2-1 (PIG) - j2-2 (PGND)
    W - B
    Power source
    Always
    9 to 16 V
    j2-2 (PGND) - Body ground
    B - Body ground
    Power ground
    Always
    Below 1 Ω
    a-1 (PHA) - j2-2 (PGND)
    # - B
    A phase motor output
    Engine running
    Steering wheel turned
    Value changes within 4 to 35 V range
    a-2 (PHB) - j2-2 (PGND)
    # - B
    B phase motor output
    Engine running
    Steering wheel turned
    Value changes within 4 to 35 V range
    a-3 (PHC) - j2-2 (PGND)
    # - B
    C phase motor output
    Engine running
    Steering wheel turned
    Value changes within 4 to 35 V range

    HINT:
    # means that the motor terminal is tightened directly to the ECU with bolts.