Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (for 2AR-FE without Wireless Door Lock)

POWER STEERING SYSTEM (for 2AR-FE without Wireless Door Lock) > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA

NOTICE:
  1. Freeze frame data values will vary depending on the measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even if the values are within specifications.
  2. Turn the ignition switch to ON and park the vehicle on level ground. Check the freeze frame data by using the Techstream.

  1. Turn the ignition switch off.

  2. Connect the Techstream to the DLC3.

  3. Turn the ignition switch to ON.

  4. Turn the Techstream on.

  5. Check the freeze frame data on the Techstream.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Meter Vehicle Velocity
    Vehicle speed from meter/
    Min.: 0.0 km/h (0.0mph)
    Max.: 300.0 km/h (186.4 mph)
    0 km/h (0 mph)
    Engine running and vehicle stopped
    No significant fluctuation
    Engine running and vehicle driven at constant speed
    Engine Revolution
    Engine speed/
    Min.: 0 rpm
    Max.: 12800 rpm
    No significant fluctuation
    Engine running at a constant speed
    Motor Actual Current
    Current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    -The value increases when turning right and decreases when turning left
    Engine running and steering wheel being turned
    Command Value Current
    Requested current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    -The value increases when turning right and decreases when turning left
    Engine running and steering wheel being turned
    Thermistor Temperature
    ECU substrate temperature/
    Min.: -50.0°C (-58.0°F)
    Max.: 150.0°C (302.0°F)
    -50 to 150°C (-58 to 302°F)
    -
    PIG Power Supply
    Power source voltage to activate motor/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    Always
    IG Power Supply
    ECU power source voltage/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    Ignition switch ON
    Steering Wheel Torque
    Steering wheel torque/
    Min.: -327.68 Nm
    Max.: 7.00 Nm
    Value changes in proportion to steering effort
    -The value increases when turning left and decreases when turning right
    Engine running and steering wheel being turned
    Torque Sensor 1 Output
    Torque sensor 1 output value/
    Min.: 0.0000 V
    Max.: 4.9725 V
    2.3 to 2.7 V
    Engine running and steering wheel not being turned (without load)
    2.5 to 3.8 V
    Engine running and steering wheel being turned to right with vehicle stopped
    1.2 to 2.5 V
    Engine running and steering wheel being turned to left with vehicle stopped
    Torque Sensor 2 Output
    Torque sensor 2 output value/
    Min.: 0.0000 V
    Max.: 4.9725 V
    2.3 to 2.7 V
    Engine running and steering wheel not being turned (without load)
    1.2 to 2.5 V
    Engine running and steering wheel being turned to right with vehicle stopped
    2.5 to 3.8 V
    Engine running and steering wheel being turned to left with vehicle stopped
    TRQ1 Zero Point Value
    Zero point value of torque sensor 1/
    Min.: 0.0000 V
    Max.: 4.9725 V
    2.3 to 2.7 V
    Engine running and steering wheel not being turned (without load)
    TRQ2 Zero Point Value
    Zero point value of torque sensor 2/
    Min.: 0.0000 V
    Max.: 4.9725 V
    2.3 to 2.7 V
    Engine running and steering wheel not being turned (without load)
    Motor Terminal Volt(+)
    Motor terminal M1 voltage/
    Min.: 0.0 V
    Max.: 25.5 V
    9 to 16 V
    Engine running and steering wheel being turned to right
    Below 1 V
    Engine running and steering wheel being turned to left
    Motor Terminal Volt(-)
    Motor terminal M2 voltage/
    Min.: 0.0 V
    Max.: 25.5 V
    Below 1 V
    Engine running and steering wheel being turned to right
    9 to 16 V
    Engine running and steering wheel being turned to left