Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (for 2GR-FE)

DTC    C1551    IG Power Supply Voltage Malfunction

for Preparation Click here


DESCRIPTION

The power steering ECU assembly distinguishes the engine switch status as on (IG) or off through the IG power source circuit.

DTC No.
DTC Detection Condition
Trouble Area
C1551
IG power source circuit malfunction inside ECU
  1. EPS-IG1 fuse
  2. IG power source circuit
  3. ECU wire sub-assembly
  4. Power steering ECU assembly

WIRING DIAGRAM


C250100E01


INSPECTION PROCEDURE

NOTICE:
If the power steering ECU assembly has been replaced, perform assist map writing (Click here).

HINT:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
  1. Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

    OK:
    The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.

  1. Check that the ground wire is securely installed with the bolt .

    OK:
    The ground wire is securely installed with the bolt.



NG
CONNECT CONNECTOR OR INSTALL GROUND WIRE
OK


2.READ VALUE USING TECHSTREAM (IG POWER SUPPLY)
  1. Turn the engine switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / EMPS / Data List.

  1. Select the item "IG power supply" in the Data List and read the value displayed on the Techstream.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG power supply
    IG power supply/
    Min.: 0 V
    Max.: 20.1531 V
    9 to 16 V
    Engine switch on (IG)

    OK:
    The normal condition value is displayed on the Techstream.



NG
Go to step 3
OK

CHECK INTERMITTENT PROBLEMS (Click here)  

3.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)


    C240359E03
  1. Disconnect the Ij2 connector from the ECU wire sub-assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Ij2-5 (IG) - Body ground
    Engine switch on (IG)
    9 to 16 V

Text in Illustration 
*a
Front view of wire harness connector
(to ECU Wire Sub-assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK ECU WIRE SUB-ASSEMBLY


    C240351E04
  1. Connect the Ij2 connector to the ECU wire sub-assembly.

  1. Disconnect the power steering ECU assembly j3 and j2 connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    j3-1 (IG) - Body ground
    Engine switch on (IG)
    9 to 16 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    j2-2 (PGND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Power Steering ECU Assembly)


NG
REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)