Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (for 2GR-FE)

DTC    C1552    PIG Power Supply Voltage Malfunction

DTC    C1554    Power Supply Relay Failure

for Preparation Click here


DESCRIPTION

When a problem occurs in the power steering system, the power source relay circuit is shut off to stop the power assist.

DTC No.
DTC Detection Condition
Trouble Area
C1552
PIG power source circuit malfunction inside ECU
  1. EPS fuse
  2. PIG power source circuit
  3. ECU wire sub-assembly
  4. Power steering ECU assembly
C1554
Power source relay circuit malfunction
  1. EPS fuse
  2. PIG power source circuit
  3. ECU wire sub-assembly
  4. Power steering ECU assembly

WIRING DIAGRAM


C250101E01


INSPECTION PROCEDURE

NOTICE:
If the power steering ECU assembly has been replaced, perform assist map writing (Click here).

HINT:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
  1. Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

    OK:
    The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.

  1. Check that the ground wire is securely installed with the bolt .

    OK:
    The ground wire is securely installed with the bolt.



NG
CONNECT CONNECTOR OR INSTALL GROUND WIRE
OK


2.READ VALUE USING TECHSTREAM (PIG POWER SUPPLY)
  1. Turn the engine switch off.

  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / EMPS / Data List.

  1. Select the item "PIG Power Supply" in the Data List and read the value displayed on the Techstream.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    PIG Power Supply
    PIG power supply/
    Min.: 0 V
    Max.: 20.1531 V
    9 to 16 V
    Engine running and steering wheel being turned

    OK:
    The normal condition value is displayed on the Techstream.



NG
Go to step 3
OK

CHECK INTERMITTENT PROBLEMS (Click here)  

3.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)


    C240360E03
  1. Disconnect the Ij1 connector from the ECU wire sub-assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Ij1-1 (PIG) - Body ground
    Always
    9 to 16 V

Text in Illustration 
*a
Front view of wire harness connector
(to ECU Wire Sub-assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK ECU WIRE SUB-ASSEMBLY


    C240344E04
  1. Connect the Ij1 connector to the ECU wire sub-assembly.

  1. Disconnect the power steering ECU assembly j2 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    j2-1 (PIG) - Body ground
    Always
    9 to 16 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    j2-2 (PGND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)



NG
REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)