Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM

DTC    B2342    Switch Failure

for Preparation Click here


DESCRIPTION

This DTC is stored when the sliding roof ECU (sliding roof drive gear sub-assembly) detects that the sliding roof switch is stuck for 30 seconds or more.

DTC No.
DTC Detection Condition
Trouble Area
B2342
Sliding roof ECU (sliding roof drive gear sub-assembly) detects sliding roof switch is stuck for 30 seconds or more.
  1. Sliding roof ECU (Sliding roof drive gear sub-assembly)
  2. Sliding roof switch (Roof console box assembly)
  3. Wire harness or connector

WIRING DIAGRAM

Refer to DTC B2341 .

INSPECTION PROCEDURE

NOTICE:
When the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, it requires initialization (Click here).

1.READ VALUE USING TECHSTREAM (SLIDING ROOF SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Sliding Roof / Data List.

  1. Read the Data List according to the display on the Techstream.

    Sliding Roof (Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Open Switch Failure(Past)
    Open switch failure signal (Past)/ON or OFF
    ON: Sliding roof open switch failure signal (Past)
    OFF: No sliding roof open switch failure signal (Past)
    -
    Close Switch Failure(Past)
    Close switch failure signal (Past)/ON or OFF
    ON: Sliding roof close switch failure signal (Past)
    OFF: No sliding roof close switch failure signal (Past)
    -
    Up Switch Failure(Past)
    Up switch failure signal (Past)/ON or OFF
    ON: Sliding roof tilt up switch failure signal (Past)
    OFF: No sliding roof tilt up switch failure signal (Past)
    -
    Down Switch Failure(Past)
    Down switch failure signal (Past)/ON or OFF
    ON: Sliding roof tilt down switch failure signal (Past)
    OFF: No sliding roof tilt down switch failure signal (Past)
    -
    Open Switch Failure(Current)
    Open switch failure signal (Current)/ON or OFF
    ON: Sliding roof open switch failure signal (Current)
    OFF: No sliding roof open switch failure signal (Current)
    -
    Close Switch Failure(Current)
    Close switch failure signal (Current)/ON or OFF
    ON: Sliding roof close switch failure signal (Current)
    OFF: No sliding roof close switch failure signal (Current)
    -
    Up Switch Failure(Current)
    Up switch failure signal (Current)/ON or OFF
    ON: Sliding roof tilt up switch failure signal (Current)
    OFF: No sliding roof tilt up switch failure signal (Current)
    -
    Down Switch Failure(Current)
    Down switch failure signal (Current)/ON or OFF
    ON: Sliding roof tilt down switch failure signal (Current)
    OFF: No sliding roof tilt down switch failure signal (Current)
    -

    OK:
    "OFF" appears on the Techstream screen.



NG
Go to step 2
OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (Click here)  

2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BODY GROUND)
  1. Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.

  1. Disconnect the S12 sliding roof switch (roof console box assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S4-7 (OPN) - Body ground
    Always
    10 kΩ or higher
    S4-6 (DWN) - Body ground
    Always
    10 kΩ or higher
    S4-5 (CLS) - Body ground
    Always
    10 kΩ or higher
    S4-4 (UP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY)


    B270995E01
  1. Remove the sliding roof switch (roof console box assembly) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (UP) - 1 (GND)
    UP switch is pressed
    Below 1 Ω
    5 (UP) - 1 (GND)
    UP switch is not pressed
    10 kΩ or higher
    4 (DOWN) - 1 (GND)
    DOWN switch is pressed
    Below 1 Ω
    4 (DOWN) - 1 (GND)
    DOWN switch is not pressed
    10 kΩ or higher
    3 (OPN) - 1 (GND)
    OPEN switch is pressed
    Below 1 Ω
    3 (OPN) - 1 (GND)
    OPEN switch is not pressed
    10 kΩ or higher
    2 (CLS) - 1 (GND)
    CLOSE switch is pressed
    Below 1 Ω
    2 (CLS) - 1 (GND)
    CLOSE switch is not pressed
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Sliding Roof Switch (Roof Console Box Assembly))



NG
REPLACE SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY) (Click here)
OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (Click here)