Home › Drivetrain ยท U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > REASSEMBLY

for Preparation Click here



HINT:
Check bearing position and installation direction.

C203284E01


C238855E01


Mark
Front Race Diameter
Inside / Outside [mm (in.)]
Thrust Bearing Diameter
Inside / Outside [mm (in.)]
Rear Race Diameter
Inside / Outside [mm (in.)]
A
-
57.7 (2.27) / 75.2 (2.96)
-
B
-
29.1 (1.15) / 48.6 (1.91)
30.7 (1.21) / 48.3 (1.90)
C
-
62.6 (2.46) / 82.4 (3.24)
65.9 (2.59) / 82.3 (3.24)
D
59.4 (2.34) / 76 (2.99)
53.46 (2.10) / 79 (3.11)
-
E
-
56.1 (2.21) / 81.1 (3.19)
-
F
-
61.2 (2.41) / 79 (3.11)
-
G
-
28 (1.10) / 47.1 (1.85)
26.1 (1.03) / 44 (1.73)
H
52.2 (2.06) / 70.4 (2.77)
48.9 (1.93) / 72.0 (2.83)
-



1. INSTALL COUNTER DRIVE GEAR BEARING

HINT:
Perform this procedure only when the counter drive gear bearing or transaxle case sub-assembly is replaced.



    C138721E01
  1. Using SST and a press, install a new counter drive gear bearing and snap ring to the transaxle case sub-assembly.

    SST
    09950-60020   (09951-01030)
    09950-70010   (09951-07100)



2. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL


    C188148E01
  1. Coat the lip of a new manual valve lever shaft oil seal with a small amount of MP grease.

  1. Using SST and a hammer, tap in the manual valve lever shaft oil seal.

    SST
    09950-60010   (09951-00230)
    09950-70010   (09951-07100)

    Oil seal tap in depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

    NOTICE:
    Check that the oil seal is installed in the correct direction.



3. INSTALL MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY


    C201357
  1. Install the manual valve lever shaft sub-assembly to the transaxle case sub-assembly.

    NOTICE:
    Do not damage the manual valve lever shaft oil seal while installing the manual valve lever shaft sub-assembly to the transaxle case sub-assembly.



    C201356
  1. Using needle-nose pliers, install the manual valve shaft retainer spring to the transaxle case sub-assembly.



4. INSTALL PARKING LOCK ROD SUB-ASSEMBLY


    C201355
  1. Align the slot with the notches on the manual valve lever shaft sub-assembly and install the parking lock rod sub-assembly.



5. INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY


    C201354
  1. Install the manual detent spring sub-assembly and manual detent spring cover to the transaxle case sub-assembly with the bolt.

    Torque:
    23 N*m{ 231 kgf*cm , 17 ft.*lbf }

    NOTICE:
    Make sure to install the manual detent spring sub-assembly first and then the manual detent spring cover.



6. INSTALL NO. 3 BRAKE PISTON


    C201353
  1. Coat 2 new O-rings with ATF and install them to the No. 3 brake piston.

    NOTICE:
    Ensure that the 2 O-rings are not twisted.



    C201352E02
  1. Temporarily install the No. 3 brake piston to the transaxle case sub-assembly.
    Text in Illustration 
    *1
    No. 3 Brake Piston



    C201530E02
  1. Temporarily install the pawl stopper plate to the transaxle case sub-assembly with the 2 bolts.
    Text in Illustration 
    *1
    No. 3 Brake Piston
    *2
    Pawl Stopper Plate

    NOTICE:
    After installing, make sure that the protrusions on the No. 3 brake piston and the grooves on the pawl stopper plate are aligned.

  1. Press the No. 3 brake piston into the transaxle case sub-assembly.

    NOTICE:
    Make sure that the lip of the No. 3 brake piston is not twisted and does not get caught in the transaxle case sub-assembly.

    HINT:
    Use the installation surface of the return spring to press the piston into the transaxle case sub-assembly.

  1. Remove the 2 bolts and pawl stopper plate from the transaxle case sub-assembly.



    C201531E02
  1. Install the brake piston return spring to the transaxle case sub-assembly.
    Text in Illustration 
    *1
    No. 3 Brake Piston
    *2
    Brake Piston Return Spring

    NOTICE:
    Install the brake piston return spring as shown in the illustration.



    C201486E02
  1. Place SST on the brake piston return spring and compress the brake piston return spring with a press.
    Text in Illustration 
    *1
    Snap Ring

    SST
    09387-00070  

    NOTICE:
    Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.

  1. Using a screwdriver, install the snap ring to the transaxle case sub-assembly as shown in the illustration.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.
    2. Be sure to align the opening of the snap ring with one of the protrusions on the brake piston return spring as shown in the illustration.



7. INSTALL COUNTER DRIVE GEAR


    C137423E02
  1. Using SST and a press, install a new counter drive gear bearing inner race (front side) to the counter drive gear.

    SST
    09387-00020  



    C224458E01
  1. Using SST, install a new counter drive gear bearing inner race (rear side) and counter drive gear to the transaxle case sub-assembly.

    SST
    09223-15030  
    09527-17011  
    09950-60020   (09951-00810)
    09950-70010   (09951-07100)

    NOTICE:
    There should not be any clearance between the counter drive gear bearing inner race (front side) and counter drive gear.



8. INSTALL FRONT PLANETARY GEAR ASSEMBLY


    C201488E01
  1. Using SST and a press, press in a new front planetary gear assembly to the transaxle case sub-assembly.

    SST
    09223-15030  
    09527-17011  
    09951-01100  



9. INSTALL NO. 2 BRAKE PISTON


    C201346
  1. Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.

    NOTICE:
    Ensure that the 2 O-rings are not twisted.



    C138726
  1. Install the No. 2 brake piston to the transaxle case sub-assembly.

    NOTICE:
    Be careful not to damage the O-rings.



10. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    C201489E01
  1. Install the 1st and reverse brake return spring to the transaxle case sub-assembly.

  1. Place SST on the 1st and reverse brake return spring and compress the 1st and reverse brake return spring with a press.

    SST
    09387-00060  

    NOTICE:
    Stop the press when the 1st and reverse brake return spring is flush with the snap ring groove. This prevents the 1st and reverse brake return spring from being deformed.

  1. Using a screwdriver, install the snap ring to the transaxle case sub-assembly as shown in the illustration.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.
    2. Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case sub-assembly as shown in the illustration.



11. INSTALL NO. 2 BRAKE DISC


    C238853E01
  1. Install the 4 No. 2 brake discs, 4 No. 2 brake plates, and No. 2 brake flange to the transaxle case sub-assembly.
    Text in Illustration 
    *1
    No. 2 Brake Flange
    *2
    No. 2 Brake Plate
    *3
    No. 2 Brake Disc

    NOTICE:
    Make sure that the discs, plates, and flange are installed in the correct order.



    C201490
  1. Using a screwdriver, install the snap ring to the transaxle case sub-assembly.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.
    2. Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case sub-assembly as shown in the illustration.



12. INSPECT CLEARANCE OF NO. 2 BRAKE


    C238856
  1. Using a dial indicator, measure the clearance of the No. 2 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

    Standard clearance:
    0.707 to 0.974 mm (0.0278 to 0.0383 in.)

    HINT:
    Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.

    If the clearance is not as specified, select an appropriate No. 2 brake flange so that the clearance will be within the specified range.
    No. 2 Brake Flange Thickness 
    Mark
    Thickness [mm (in.)]
    40
    4.0 (0.157)
    41
    4.1 (0.161)
    42
    4.2 (0.165)
    43
    4.3 (0.169)
    44
    4.4 (0.173)



13. INSTALL PLANETARY RING GEAR FLANGE


    C136480E02
  1. Install the planetary ring gear flange to the planetary ring gear.
    Text in Illustration 
    *1
    Snap Ring
    *2
    Planetary Ring Gear Flange
    *3
    Planetary Ring Gear

  1. Using a screwdriver, install the snap ring to the planetary ring gear.

    NOTICE:
    Confirm that the snap ring is correctly located in the groove of the planetary ring gear.



14. INSTALL ONE-WAY CLUTCH ASSEMBLY


    C201345E02
  1. Install the outer race retainer to the one-way clutch assembly.
    Text in Illustration 
    *1
    One-way Clutch Assembly
    *2
    Outer Race Retainer
    *3
    Planetary Ring Gear

  1. Install the one-way clutch assembly to the planetary ring gear.

    NOTICE:
    Make sure that the one-way clutch assembly is positioned in the correct direction as shown in the illustration.



    C201491E02
  1. Coat the thrust needle roller bearing with ATF, and install it onto the front planetary gear assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    Bearing Diameter 
    -
    Inside [mm (in.)]
    Outside [mm (in.)]
    Bearing
    56.1 (2.21)
    81.1 (3.19)

    NOTICE:
    Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.

  1. Install the one-way clutch assembly with the planetary ring gear to the transaxle case sub-assembly.

    NOTICE:
    Make sure that there is no clearance between the retainer and the claw on the one-way clutch assembly. If there is any clearance, the spring of the retainer will be deformed.



    C136477
  1. Using a screwdriver, install the snap ring to the transaxle case sub-assembly.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.
    2. Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case sub-assembly as shown in the illustration.



15. INSTALL DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING LH (OUTER RACE)


    C137443E01
  1. Using SST and a hammer, install a new differential drive pinion tapered roller bearing LH (outer race) to the transaxle case sub-assembly.

    SST
    09950-60010   (09951-00630)
    09950-70010   (09951-07100)

    NOTICE:
    Be sure to install the differential drive pinion tapered roller bearing so that there is no clearance between the bearing outer race and the transaxle case sub-assembly. If there is any clearance, the turning torque of the counter drive gear cannot be measured correctly.



16. INSTALL PARKING LOCK PAWL


    C201343E02
  1. Install the parking lock pawl to the transaxle case sub-assembly with the parking lock pawl shaft.
    Text in Illustration 
    *1
    Parking Lock Pawl Pin
    *2
    Parking Lock Pawl Shaft
    *3
    Spring
    *4
    Parking Lock Pawl

  1. Install the parking lock pawl pin to the transaxle case sub-assembly.



    C137444
  1. Install the torsion spring to the parking lock pawl.

    NOTICE:
    Make sure that one end of the spring is secured in the hole of the transaxle case sub-assembly and the other end is positioned on the parking lock pawl as shown in the illustration.



17. INSTALL PARKING LOCK SLEEVE


    C201342
  1. Install the parking lock sleeve to the transaxle case sub-assembly.



18. INSTALL PAWL STOPPER PLATE


    C201341
  1. Install the pawl stopper plate to the transaxle case sub-assembly with the 2 bolts.

    Torque:
    23 N*m{ 231 kgf*cm , 17 ft.*lbf }



19. INSTALL NO. 1 TRANSMISSION CASE PLATE


    C203287E01
  1. Clean and degrease the bolt and the installation hole in the transaxle case sub-assembly.

  1. Apply adhesive to 2 or 3 threads on the ends of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the No. 1 transmission case plate to the transaxle case sub-assembly with the bolt.

    Torque:
    23 N*m{ 231 kgf*cm , 17 ft.*lbf }

    HINT:
    Tighten the bolt while part A of the No. 1 transmission case plate contacts the transaxle case sub-assembly as shown in the illustration.



20. INSTALL PAWL SHAFT CLAMP


    C201339
  1. Install the pawl shaft clamp to the transaxle case sub-assembly with the bolt.

    Torque:
    23 N*m{ 231 kgf*cm , 17 ft.*lbf }



21. INSTALL DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING RH (INNER RACE)


    C138250E01
  1. Using SST and a press, install a new differential drive pinion tapered roller bearing RH (inner race) to the counter driven gear sub-assembly.

    SST
    09950-60010   (09951-00490)

    NOTICE:
    Be sure to install the differential drive pinion tapered roller bearing so that there is no clearance between the bearing and the counter driven gear. If there is any clearance, the turning torque of the counter drive gear cannot be measured correctly.



22. INSTALL DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING LH (INNER RACE)


    C138251E01
  1. Using SST and a press, install a new differential drive pinion tapered roller bearing LH (inner race) to the counter driven gear sub-assembly.

    SST
    09950-60010   (09951-00400)

    NOTICE:
    Be sure to install the differential drive pinion tapered roller bearing so that there is no clearance between the bearing and the counter driven gear. If there is any clearance, the turning torque of the counter drive gear cannot be measured correctly.



23. INSTALL COUNTER DRIVEN GEAR


    C201336
  1. Install the counter driven gear to the transaxle case sub-assembly.



24. INSTALL COUNTER DRIVE GEAR NUT


    C201334E01
  1. Turn the manual valve lever shaft counterclockwise to set it to the P position as shown in the illustration.



    C201527E01
  1. Using SST, install a new counter drive gear nut.

    SST
    09387-00130  

    Torque:
    120 N*m{ 1224 kgf*cm , 88 ft.*lbf }



    C201335E01
  1. Turn the manual valve lever shaft 2 notches clockwise to set it to the N position as shown in the illustration.



    C138252E01
  1. Using SST and a torque wrench, measure the turning torque of the bearing while rotating SST at 60 rpm.

    SST
    09387-00130  

    Turning torque:
    0.1 to 0.8 N*m (1 to 8 kgf*cm, 1 to 7 in.*lbf)

    If the measured value is not within the specified range, gradually tighten the nut until the turning torque falls within the specified range.

    Maximum torque:
    180 N*m (1835 kgf*cm, 132 ft.*lbf)



    C201333E01
  1. Using SST and a hammer, stake the counter drive gear nut.

    SST
    09930-00010  



25. INSTALL FRONT DIFFERENTIAL CASE


    C201332
  1. Install the front differential case to the transaxle case sub-assembly.



26. INSTALL NO. 1 BRAKE PISTON


    C136466E04
  1. Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.

    NOTICE:
    Ensure that the 2 O-rings are not twisted.



    C138253
  1. Install the No. 1 brake piston to the front oil pump assembly.

    NOTICE:
    Be careful not to damage the O-rings.



27. INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C136464
  1. Install the 3 2nd brake piston return springs to the front oil pump assembly.

    NOTICE:
    Make sure that the 3 2nd brake piston return springs are installed onto the protrusions on the front oil pump assembly.



28. INSTALL NO. 1 BRAKE DISC


    C201529E03
  1. Install the 3 No. 1 brake discs, 3 No. 1 brake plates, and No. 1 brake flange to the front oil pump assembly.
    Text in Illustration 
    *1
    No. 1 Brake Flange
    *2
    No. 1 Brake Plate
    *3
    No. 1 Brake Disc

    NOTICE:
    1. Make sure that the discs, plates, and flange are installed in the correct order.
    2. Be sure to install the flange in the correct direction.



    C189783E01
  1. Place SST on the flange and compress the flange with a press.

    SST
    09387-00070  
    09495-65040  

    NOTICE:
    Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.

  1. Using a screwdriver, install the snap ring to the front oil pump assembly as shown in the illustration.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the oil pump.
    2. Make sure to align the protruding part of the snap ring with the indented part (#1) of the front oil pump and gear body assembly shown in the illustration to install the snap ring.



    C176220
  1. Install the brake snap ring stopper to the front oil pump assembly.

    NOTICE:
    Be sure to install the brake snap ring stopper in the correct direction.



    C201519E01
  1. Using a screwdriver, install the snap ring to the front oil pump assembly as shown in the illustration.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the oil pump.
    2. Make sure to align the protruding part of the snap ring with the indented part (#2) of the front oil pump assembly shown in the illustration to install the snap ring.



    C153481E03
  1. Check that the brake snap ring stopper can be turned by hand.
    Text in Illustration 
    *1
    Brake Snap Ring Stopper
    *2
    Snap Ring
    *a
    Correctly Installed

    NOTICE:
    If the brake snap ring stopper cannot be turned by hand, the brake snap ring stopper may have been installed upside down, or the snap ring may not have been completely located in the groove on the oil pump. Remove and reinstall the snap ring and the brake snap ring stopper.



29. INSPECT CLEARANCE OF NO. 1 BRAKE


    C138258
  1. Using a dial indicator, measure the clearance of the No. 1 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

    Standard clearance:
    0.601 to 0.819 mm (0.0237 to 0.0322 in.)

    HINT:
    Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.

    If the clearance is not as specified, select an appropriate No. 1 brake flange so that the clearance will be within the specified range.
    No. 1 Brake Flange Thickness 
    Mark
    Thickness [mm (in.)]
    30
    3.0 (0.118)
    31
    3.1 (0.122)
    32
    3.2 (0.126)
    33
    3.3 (0.130)
    34
    3.4 (0.134)
    35
    3.5 (0.138)



30. INSTALL UNDERDRIVE PLANETARY SUN GEAR


    C202904E02
  1. Coat the thrust needle roller bearing with ATF, and install it to the front oil pump assembly.
    Text in Illustration 
    *1
    Underdrive Planetary Sun Gear
    *2
    Thrust Needle Roller Bearing
    Bearing Diameter 
    -
    Inside [mm (in.)]
    Outside [mm (in.)]
    Bearing
    57.7 (2.27)
    75.2 (2.96)

    NOTICE:
    Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.

  1. Install the underdrive planetary sun gear to the front oil pump assembly.



31. INSTALL INPUT SHAFT SUB-ASSEMBLY


    C202905E02
  1. Coat 3 new oil seal rings with ATF and install them to the input shaft sub-assembly.
    Text in Illustration 
    *1
    Thrust Bearing Race
    *2
    Thrust Needle Roller Bearing
    *3
    Input Shaft
    *4
    Oil Seal Ring

    NOTICE:
    Do not expand the gap of the oil seal ring too much.

  1. Coat the thrust needle roller bearing and thrust bearing race with ATF, and install them on the input shaft sub-assembly.
    Bearing and Race Diameter 
    -
    Inside [mm (in.)]
    Outside [mm (in.)]
    Bearing
    29.1 (1.15)
    48.6 (1.91)
    Race
    30.7 (1.21)
    48.3 (1.90)

    NOTICE:
    Be sure to install the thrust needle roller bearing in the correct direction.



    C136459
  1. Install the input shaft to the front oil pump assembly.



32. INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY


    C201331E02
  1. Using a snap ring expander, install the snap ring to the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Planetary Sun Gear Sub-assembly
    *2
    Underdrive Planetary Gear Assembly
    *3
    Snap Ring

  1. Using a snap ring expander, install the planetary sun gear sub-assembly to the underdrive planetary gear assembly with the snap ring expanded.



33. INSTALL NO. 3 BRAKE HUB


    C202906E02
  1. Coat the thrust needle roller bearing with ATF and install it on the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Thrust Bearing Race
    *2
    Thrust Needle Roller Bearing
    Bearing and Race Diameter 
    -
    Inside [mm (in.)]
    Outside [mm (in.)]
    Bearing
    62.6 (2.47)
    82.4 (3.24)
    Race
    65.9 (2.59)
    82.3 (3.24)

    NOTICE:
    Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.

  1. Coat the thrust bearing race with MP grease and install it to the No. 3 brake hub.



    C136454
  1. Install the No. 3 brake hub to the underdrive planetary gear assembly.



34. INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY


    C136458
  1. Install the underdrive planetary gear assembly to the front oil pump assembly.



35. INSTALL NO. 3 BRAKE DISC


    C136452E02
  1. Install the 2 No. 3 brake flanges, 3 No. 3 brake discs, and 2 No. 3 brake plates to the front oil pump assembly.
    Text in Illustration 
    *1
    No. 3 Brake Flange
    *2
    No. 3 Brake Plate
    *3
    No. 3 Brake Disc

    NOTICE:
    Make sure that the discs, plates, and flanges are installed in the correct order.



    C136451E02
  1. Using a screwdriver, install the snap ring to the front oil pump assembly.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the oil pump.
    2. Make sure that the snap ring ends are positioned as shown in the illustration (A).



36. INSPECT CLEARANCE OF NO. 3 BRAKE


    C238854E01
  1. Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension A) while a load of 500 N (51 kgf, 112.4 lbf) is being applied to the flange.
    Text in Illustration 
    *1
    Front Oil Pump Assembly
    *2
    No. 3 Brake
    *a
    Dimension A
    *b
    Dimension B
    *c
    Contact Surface of Front Oil Pump Assembly

    HINT:
    Measure dimension A at 3 points where the flange diameter is approximately 166 mm (6.54 in.) and calculate the average.

  1. Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).

    HINT:
    Measure dimension B at 3 points where the No. 3 brake diameter is approximately 166 mm (6.54 in.) and calculate the average.

  1. Calculate the clearance value using the following formula:
    Clearance = Dimension B - Dimension A - Flange Thickness

    Standard clearance:
    0.599 to 0.799 mm (0.0236 to 0.0315 in.)

    If the clearance is not as specified, select an appropriate brake flange so that the clearance will be within the specified range.
    No. 3 Brake Flange Thickness 
    Mark
    Thickness [mm (in.)]
    38
    3.80 (0.150)
    39
    3.90 (0.154)
    40
    4.00 (0.157)
    41
    4.10 (0.161)
    42
    4.20 (0.165)
    43
    4.30 (0.169)



37. INSTALL FRONT OIL PUMP ASSEMBLY


    C201330E02
  1. Coat a new O-ring with ATF and install it to the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Thrust Bearing Race
    *2
    Thrust Needle Roller Bearing
    *3
    O-ring

  1. Coat the thrust needle roller bearing and thrust bearing race with ATF and install them on the counter drive gear nut.
    Bearing and Race Diameter 
    -
    Inside [mm (in.)]
    Outside [mm (in.)]
    Bearing
    53.46 (2.10)
    79 (3.11)
    Race
    59.4 (2.34)
    76 (2.99)

    NOTICE:
    Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



    C201329
  1. Coat a new O-ring with ATF and install it to the front oil pump assembly.



    C201328E02
  1. Install the front oil pump assembly to the transaxle case sub-assembly with the 7 bolts.
    Text in Illustration 
    *1
    O-ring

    Torque:
    23 N*m{ 231 kgf*cm , 17 ft.*lbf }

  1. Coat a new O-ring with ATF and install it to the front oil pump assembly.



38. INSTALL TRANSAXLE HOUSING OIL SEPARATOR


    C201327
  1. Clean and degrease the 3 bolts and the installation holes in the transaxle housing.

  1. Apply adhesive to 2 or 3 threads on the ends of the 3 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the transaxle housing oil separator to the transaxle housing with the 3 bolts.

    Torque:
    23 N*m{ 231 kgf*cm , 17 ft.*lbf }



39. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE


    C201326
  1. Install the differential gear lube apply tube to the transaxle housing.

    NOTICE:
    Insert the differential gear lube apply tube into the transaxle housing until it makes contact with the stopper.

  1. Clean and degrease the bolt and the installation hole in the transaxle housing.

  1. Apply adhesive to 2 or 3 threads on the ends of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the apply tube clamp to the differential gear lube apply tube with the bolt.

    Torque:
    23 N*m{ 231 kgf*cm , 17 ft.*lbf }

    NOTICE:
    There should be clearance between the differential lube apply tube and apply tube clamp.



40. INSTALL DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING RH (OUTER RACE)


    C138261E01
  1. Install the shim to the transaxle housing.

  1. Using SST, install a new differential drive pinion tapered roller bearing RH (outer race) to the transaxle housing.

    SST
    09950-60020   (09951-00710)
    09950-70010   (09951-07100)

    NOTICE:
    Be sure to install the differential drive pinion tapered roller bearing so that there is no clearance between the bearing outer race, shim and the transaxle housing. If there is any clearance, the turning torque of the counter drive gear cannot be measured correctly.



41. ADJUST COUNTER DRIVEN GEAR PRELOAD


    C205232E01
  1. Remove packing material from the contact surfaces between the transaxle housing and transaxle case sub-assembly.

  1. Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

    Torque:
    Bolt A:
    23 N*m{ 231 kgf*cm , 17 ft.*lbf }
    except Bolt A:
    31 N*m{ 312 kgf*cm , 22 ft.*lbf }



    C138262E01
  1. Using SST and a torque wrench, measure the turning torque of the counter driven gear while rotating SST at 10 rpm.

    SST
    09564-33010  

    Turning torque:
    Differential side bearing preload + 2.68 to 5.85 N*m (27.33 to 59.65 kgf*cm, 23.73 to 51.77 in.*lbf)

    If the turning torque is not within the specified range, refer to the table below to select a shim of the counter driven gear front tapered roller bearing (outer race) so that the turning torque is within the specified range.
    Shim Thickness 
    Thickness
    Thickness
    Thickness
    Thickness
    2.000 (0.0787)
    2.275 (0.0896)
    2.550 (0.100)
    2.825 (0.111)
    2.025 (0.0797)
    2.300 (0.0906)
    2.575 (0.101)
    2.850 (0.112)
    2.050 (0.0807)
    2.325 (0.0915)
    2.600 (0.102)
    2.875 (0.113)
    2.075 (0.0817)
    2.350 (0.0925)
    2.625 (0.103)
    2.900 (0.114)
    2.100 (0.0827)
    2.375 (0.0935)
    2.650 (0.104)
    2.925 (0.115)
    2.125 (0.0837)
    2.400 (0.0945)
    2.675 (0.105)
    2.950 (0.116)
    2.150 (0.0846)
    2.425 (0.0955)
    2.700 (0.106)
    2.975 (0.117)
    2.175 (0.0856)
    2.450 (0.0965)
    2.725 (0.107)
    3.000 (0.118)
    2.200 (0.0866)
    2.475 (0.0974)
    2.750 (0.108)
    -
    2.225 (0.0876)
    2.500 (0.0984)
    2.775 (0.109)
    -
    2.250 (0.0886)
    2.525 (0.0994)
    2.800 (0.110)
    -



    C205232
  1. Remove the 20 bolts and the transaxle housing.



42. INSTALL TRANSAXLE HOUSING


    C201495
  1. Clean and degrease the contact surfaces between the transaxle housing and transaxle case sub-assembly.

    NOTICE:
    Make sure that there is no ATF on the contact surfaces.

  1. Apply FIPG to the transaxle case sub-assembly.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    1. Apply FIPG in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.
    2. After applying FIPG, install the transaxle housing to the transaxle case sub-assembly within 3 minutes and tighten the bolts within 20 minutes.



    C205494
  1. Install the transaxle housing to the transaxle case sub-assembly with the 17 bolts.

    Torque:
    31 N*m{ 312 kgf*cm , 22 ft.*lbf }



    C205495
  1. Clean and degrease the 3 bolts and the installation holes in the automatic transaxle assembly.

  1. Apply adhesive to 2 or 3 threads on the ends of the 3 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the 3 bolts.

    Torque:
    23 N*m{ 231 kgf*cm , 17 ft.*lbf }



43. INSPECT CLEARANCE OF NO. 1 CLUTCH


    C201532
  1. Install the direct multiple disc clutch assembly onto the rear transaxle cover sub-assembly.

  1. Check that the piston moves when compressed air (200 kPa, 2.0 kgf/cm2, 29 psi) is applied to the oil hole.



    C201533E02
  1. Using a feeler gauge, measure the No. 1 clutch pack clearance.
    Text in Illustration 
    *1
    Feeler Gauge

    HINT:
    Measure the clearance at 3 points where the flange diameter is approximately 152 mm (5.98 in.) and calculate the average.

    Standard pack clearance:
    0.601 to 0.819 mm (0.0237 to 0.0322 in.)

    If the pack clearance is not as specified, replace the rear multiple disc clutch assembly.



44. INSTALL REAR PLANETARY SUN GEAR ASSEMBLY


    C201526E02
  1. Coat the thrust needle roller bearing and thrust bearing race with ATF, and install them to the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Bearing Race
    Bearing and Race Diameter 
    -
    Inside [mm (in.)]
    Outside [mm (in.)]
    Bearing
    28 (1.10)
    47.1 (1.85)
    Race
    26.1 (1.03)
    44 (1.73)

    NOTICE:
    Install the rear planetary sun gear thrust needle roller bearing properly so that the temper colored side of the race will be visible.



    C201321E02
  1. Install the rear planetary sun gear assembly to the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Rear Planetary Sun Gear



    C202900
  1. Using a snap ring expander, install the snap ring to the direct multiple disc clutch assembly.



    C224456E01
  1. Coat a new O-ring with ATF and install it to the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    O-ring
    *2
    Oil Seal Ring

    NOTICE:
    Ensure that the O-ring is not twisted.

  1. Coat a new oil seal ring with ATF and install it to the intermediate shaft.



45. INSPECT CLEARANCE OF NO. 2 CLUTCH


    C202899
  1. Install the direct multiple disc clutch assembly onto the rear transaxle cover sub-assembly.

  1. Using a dial indicator, measure the No. 2 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

    HINT:
    Measure the clearance at 3 points where the diameter of the No. 2 direct multiple clutch piston is approximately 152 mm (5.98 in.) and calculate the average.

    Standard pack clearance:
    0.394 to 0.605 mm (0.0155 to 0.0238 in.)

    If the pack clearance is not as specified, replace the rear multiple disc clutch assembly.



46. INSTALL REAR MULTIPLE DISC CLUTCH ASSEMBLY


    C202901E02
  1. Coat the rear thrust needle roller bearing with ATF and install it on the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Rear Multiple Disc Clutch Assembly
    Bearing Diameter 
    -
    Inside [mm (in.)]
    Outside [mm (in.)]
    Bearing
    61.2 (2.41)
    79 (3.11)

  1. Install the direct multiple disc clutch assembly to the transaxle case sub-assembly.



47. INSPECT INTERMEDIATE SHAFT END PLAY


    C201496E02
  1. Clean the contact surfaces of the transaxle case sub-assembly and rear transaxle cover sub-assembly.

  1. As shown in the illustration, place a straightedge on the multiple direct clutch drum and measure the distance between the transaxle case sub-assembly and the straightedge using a vernier caliper (Dimension A).
    Text in Illustration 
    *a
    Dimension A



    C138268E03
  1. Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).
    Text in Illustration 
    *a
    Dimension B

  1. Calculate the end play value using the following formula:
    End play = Dimension B - Dimension A - Thrust needle roller bearing thickness

    Standard end play:
    0.022 to 1.099 mm (0.000867 to 0.0432 in.)



48. INSTALL REAR TRANSAXLE COVER SUB-ASSEMBLY


    C205308E01
  1. Using SST and a hammer, install a new needle roller bearing into the rear transaxle cover sub-assembly.

    SST
    09950-60010   (09951-00220)
    09950-70010   (09951-07100)

    Installation depth:
    21.5 to 21.9 mm (0.846 to 0.862 in.)



    C201318
  1. Clean and degrease the 2 "TORX" screws and the installation holes in the rear transaxle cover sub-assembly.

  1. Apply adhesive to 2 or 3 threads on the ends of the 2 "TORX" screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using a T30 "TORX" socket wrench, install the rear transaxle cover plate to the rear transaxle cover sub-assembly with the 2 "TORX" screws.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    C202908E02
  1. Coat the thrust needle roller bearing and thrust bearing race with ATF and install them on the rear transaxle cover sub-assembly.
    Text in Illustration 
    *1
    Oil Seal Ring
    *2
    Thrust Needle Roller Bearing
    *3
    Thrust Bearing Race
    Bearing and Race Diameter 
    -
    Inside [mm (in.)]
    Outside [mm (in.)]
    Bearing
    48.9 (1.93)
    72.0 (2.83)
    Race
    52.2 (2.06)
    70.4 (2.77)

  1. Coat 2 new oil seal rings with ATF and install them to the rear transaxle cover sub-assembly.



    C136432E01
  1. Coat 3 new O-rings with ATF and install them to the transaxle case sub-assembly.



    C138271
  1. Remove packing material from the contact surfaces between the rear transaxle cover sub-assembly and transaxle case sub-assembly.

    NOTICE:
    Make sure that there is no ATF on the contact surfaces.

  1. Apply FIPG to the transaxle case sub-assembly.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent.

    NOTICE:
    1. Apply FIPG in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.
    2. After applying FIPG, install the rear transaxle cover sub-assembly to the transaxle case sub-assembly within 3 minutes and tighten the bolts within 20 minutes.



    C136431E03
  1. Install the rear transaxle cover sub-assembly to the transaxle case sub-assembly with the 12 bolts.

    Torque:
    23 N*m{ 231 kgf*cm , 17 ft.*lbf }



    C136431E04
  1. Clean and degrease the 2 bolts and the installation holes in the transaxle case sub-assembly.

  1. Apply adhesive to 2 or 3 threads on the ends of the 2 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the 2 bolts.

    Torque:
    17 N*m{ 172 kgf*cm , 12 ft.*lbf }



49. INSTALL REAR TRANSAXLE COVER PLUG


    C201317
  1. Coat 3 new O-rings with ATF and install them to the 3 rear transaxle cover plugs.

    NOTICE:
    Ensure that the 3 O-rings are not twisted.

  1. Install the 3 rear transaxle cover plugs to the rear transaxle cover sub-assembly.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



50. INSTALL REFILL PLUG


    C162439
  1. Install a new gasket to the refill plug.

  1. Install the refill plug to the rear transaxle cover sub-assembly.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



51. INSPECT INPUT SHAFT END PLAY


    C136696
  1. Using a dial indicator, measure the input shaft end play.

    Standard end play:
    0.020 to 1.242 mm (0.000788 to 0.0488 in.)



52. INSTALL NO. 1 GOVERNOR APPLY GASKET


    C201316
  1. Coat 2 new No. 1 governor apply gaskets with ATF.

  1. Install the 2 No. 1 governor apply gaskets onto the transaxle case sub-assembly.



53. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


    C201704E03
  1. Coat the O-ring of the transmission wire with ATF.

  1. Insert the pin of the manual valve lever into the groove on the end of the manual valve and install the transmission valve body assembly onto the automatic transaxle assembly with the 11 bolts.
    Text in Illustration 
    *a
    Positioning Bolt
    Bolt Length 
    Bolt
    Length [mm (in.)]
    A
    25 (0.984)
    B
    30 (1.18)
    C and D
    35 (1.38)

    Torque:
    Bolt A, B, C:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }
    Bolt D:
    9.6 N*m{ 98 kgf*cm , 85 in.*lbf }

    NOTICE:
    1. When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and automatic transaxle assembly to interfere with each other.
    2. First, temporarily tighten the bolts marked (*a) in the illustration because they are positioning bolts.



54. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


    C201703
  1. Coat a new O-ring with ATF.

  1. Install the O-ring onto the valve body oil strainer assembly.

    NOTICE:
    Ensure that the O-ring is not twisted.



    C201702
  1. Install the valve body oil strainer assembly onto the transmission valve body assembly with the 2 bolts.

    Torque:
    9.6 N*m{ 98 kgf*cm , 85 in.*lbf }



55. INSTALL TRANSMISSION OIL CLEANER MAGNET


    C201701E04
  1. Install the 2 transmission oil cleaner magnets onto the automatic transaxle oil pan sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Transmission Oil Cleaner Magnet



56. INSTALL AUTOMATIC TRANSAXLE OIL PAN GASKET
  1. Install a new automatic transaxle oil pan gasket onto the automatic transaxle oil pan sub-assembly.



57. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    C202902
  1. Install the automatic transaxle oil pan sub-assembly with the automatic transaxle oil pan gasket onto the automatic transaxle assembly with the 17 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    NOTICE:
    Completely remove any oil or grease from the contact surfaces of the transaxle case sub-assembly and oil pan sub-assembly with the gasket before installation.



    C202903
  1. Clean and degrease the 2 bolts and the installation holes in the transaxle case sub-assembly.

  1. Apply adhesive to 2 or 3 threads on the ends of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



58. INSTALL NO. 1 TRANSMISSION OIL FILLER TUBE


    C201310
  1. Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly.

    Torque:
    0.8 N*m{ 8 kgf*cm , 7 in.*lbf }



59. INSTALL OVERFLOW PLUG


    C201309
  1. Using a 6 mm hexagon socket wrench, install the overflow plug and a new gasket to the automatic transaxle oil pan sub-assembly.

    Torque:
    40 N*m{ 408 kgf*cm , 29 ft.*lbf }



60. INSTALL NO. 2 TRANSAXLE CASE PLUG


    C134959
  1. Clean and degrease the 3 No. 2 transaxle case plugs and the installation holes in the transaxle housing.

  1. Apply adhesive to 2 or 3 threads on the ends of the 3 No. 2 transaxle case plugs.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the 3 new gaskets to the 3 No. 2 transaxle case plugs.

  1. Using a 6 mm hexagon socket wrench, install the 3 No. 2 transaxle case plugs to the transaxle housing with the gaskets.

    Torque:
    17 N*m{ 173 kgf*cm , 12 ft.*lbf }



61. INSTALL NO. 1 TRANSAXLE CASE PLUG


    C162438
  1. Coat 3 new O-rings with ATF and install them to the 3 No. 1 transaxle case plugs.

    NOTICE:
    Ensure that the 2 O-rings are not twisted.

  1. Install the 3 No. 1 transaxle case plugs to the transaxle case sub-assembly.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



62. INSTALL OIL COOLER TUBE UNION (INLET)


    C205116
  1. Coat a new O-ring with ATF and install it to the oil cooler tube union (inlet).

    NOTICE:
    Ensure that the O-ring is not twisted.

  1. Install the oil cooler tube union (inlet) to the transaxle case sub-assembly as shown in the illustration.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



63. INSTALL OIL COOLER TUBE UNION (OUTLET)


    C205117
  1. Coat a new O-ring with ATF and install it to the oil cooler tube union (outlet).

    NOTICE:
    Ensure that the O-ring is not twisted.

  1. Install the oil cooler tube union (outlet) to the transaxle case sub-assembly.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



64. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C136686
  1. Temporarily install the park/neutral position switch assembly to the transaxle case sub-assembly with the 2 bolts.

    NOTICE:
    Before installing the park/neutral position switch assembly, remove any dirt or rust on the manual valve lever shaft sub-assembly. Be sure to install the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.



    C135733E06
  1. Align the protrusions of the park/neutral position switch assembly as shown in the illustration.
    Text in Illustration 
    *1
    Protrusion

  1. Tighten the 2 bolts

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    After installing the park/neutral position switch assembly, confirm that the 2 protrusions on the switch are aligned.



65. INSTALL TRANSMISSION CONTROL SHAFT LEVER


    C136685
  1. Install the transmission control shaft lever to the manual valve lever shaft sub-assembly with the washer and nut.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



66. INSTALL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY


    C134952E04
  1. Coat a new O-ring with ATF and install it to the No. 2 breather plug.
    Text in Illustration 
    *1
    No. 1 Breather Plug
    *2
    Breather Plug Hose
    *3
    No. 2 Breather Plug
    *4
    O-ring

    NOTICE:
    Ensure that the O-ring is not twisted.

  1. Install the No. 2 breather plug to the breather plug hose.

  1. Install the No. 1 breather plug to the breather plug hose.



    C238851E01
  1. Install the transmission breather plug hose sub-assembly to the transaxle case sub-assembly.
    Text in Illustration 
    *1
    No. 2 Breather Plug
    *a
    Boss

    NOTICE:
    Ensure that the stopper on the No. 2 breather plug is in contact with the side of the boss on the transaxle case sub-assembly.