Home › Drivetrain ยท U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > REASSEMBLY

for Preparation Click here



1. BEARING POSITION


  1. Check bearing position and installation direction.


    C153478E01



    C138529E01


    Mark
    Front Race Diameter
    Inside / Outside mm (in.)
    Thrust Bearing Diameter
    Inside / Outside mm (in.)
    Rear Race Diameter
    Inside / Outside mm (in.)
    A
    -
    57.7 (2.27) / 75.2 (2.96)
    -
    B
    -
    29.1 (1.15) / 48.6 (1.91)
    30.7 (1.21) / 48.3 (1.90)
    C
    65.9 (2.59) / 80.3 (3.16)
    62.6 (2.47) / 82.4 (3.24)
    -
    D
    59.4 (2.34) / 77 (3.03)
    53.1 (2.09) / 79 (3.11)
    -
    E
    -
    56.1 (2.21) / 80.9 (3.19)
    -
    F
    -
    61.2 (2.41) / 79 (3.11)
    -
    G
    -
    28 (1.10) / 47.1 (1.85)
    26.1 (1.03) / 44 (1.73)
    H
    52.2 (2.06) / 70.4 (2.77)
    48.9 (1.93) / 72.0 (2.84)
    -



2. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL


    C188148E01
  1. Coat the lip of a new manual valve lever shaft oil seal with MP grease.

  1. Using SST and a hammer, install the manual valve lever shaft oil seal to the transaxle case.

    SST
    09950-60010   (09951-00230)
    09950-70010   (09951-07100)

    Oil seal driven in depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



3. INSTALL MANUAL VALVE LEVER SHAFT
  1. Install a new spacer to the parking lock lever sub-assembly.

  1. Install the parking lock lever sub-assembly to the manual valve lever shaft.

  1. Install a new spacer to the manual valve lever sub-assembly.

  1. Install the manual valve lever sub-assembly to the manual valve lever shaft.



    C137428
  1. Install the manual valve lever shaft to the transaxle case.

    NOTICE:
    Do not damage the manual valve lever shaft oil seal while installing the manual valve lever shaft to the transaxle case.



    C137417
  1. Using a pin punch (3 mm) and hammer, install a new slotted spring pin into the parking lock lever sub-assembly.



    C137429
  1. Turn the spacer and the lever shaft to align the smaller hole of the spacer with the staking position mark on the lever shaft.

  1. Using a pin punch, stake the spacer through the small hole.

  1. Check that the spacer does not turn.



    C136702
  1. Using a pin punch (3 mm) and hammer, install a new slotted spring pin into the manual valve lever sub-assembly.



    C137430
  1. Turn the spacer and the lever shaft to align the smaller hole of the spacer with the staking position mark on the lever shaft.

  1. Using a pin punch, stake the spacer through the small hole.

  1. Check that the spacer does not turn.



    C136680E01
  1. Using needle-nose pliers, install the manual valve shaft retainer spring to the transaxle case.



4. INSTALL PARKING LOCK ROD SUB-ASSEMBLY


    C136683
  1. Align the slot with the notches on the parking lock lever sub-assembly and install the parking lock rod sub-assembly.



5. INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY


    C134953E01
  1. Install the manual detent spring sub-assembly and cover to the transaxle case with the bolt.

    Torque:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }

    NOTICE:
    Make sure to install the manual detent spring first and then the cover.



6. INSTALL NO. 3 BRAKE PISTON


    C137432
  1. Coat the contact surface of the transaxle case with ATF.

  1. Coat the lip of the No. 3 brake piston with ATF.



    C137431
  1. Temporarily install the pawl stopper plate to the transaxle case with the 2 bolts.



    C141536E02
  1. Press the No. 3 brake piston into the transaxle case.
    Text in Illustration 
    *1
    Brake Piston Return Spring
    *2
    No. 3 Brake Piston

    NOTICE:
    1. Make sure that the lip of the No. 3 brake piston is not twisted and does not get caught in the transaxle case.
    2. After installation, make sure that the protrusions on the No. 3 brake piston and the grooves on the pawl stopper plate are aligned.

    HINT:
    Use the installation surface of the return spring to press the piston into the transaxle case.

  1. Install the return spring to the transaxle case.



    C137422E01
  1. Remove the 2 bolts and pawl stopper plate from the transaxle case.



    C138725E01
  1. Place SST on the brake piston return spring and compress the brake piston return spring using a press.

    SST
    09387-00070  

    NOTICE:
    Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.

  1. Using a screwdriver, install the snap ring to the transaxle case as shown in the illustration.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case.
    2. Be sure to align the opening of the snap ring with one of the protrusions on the brake piston return spring as shown in the illustration.



7. INSTALL COUNTER DRIVE GEAR

NOTICE:
Perform this procedure only when the counter drive gear bearing or transaxle case is replaced.



    C138721E01
  1. Using SST and a press, install a new counter drive gear bearing and snap ring to the transaxle case.

    SST
    09950-60020   (09951-01030)
    09950-70010   (09951-07100)



    C137424E01
  1. Using SST, install a new bearing inner race (rear side) and counter drive gear to the transaxle case.

    SST
    09223-15030  
    09527-17011  09950-60020   (09951-00810)
    09950-70010   (09951-07100)

    NOTICE:
    There should not be any clearance between the bearing inner race (front side) and counter drive gear.



8. INSTALL FRONT PLANETARY GEAR ASSEMBLY


    C137425E01
  1. Using SST and a press, press the planetary gear assembly onto the transaxle case.

    SST
    09223-15030  
    09527-17011  
    09951-01100  



9. INSTALL NO. 2 BRAKE PISTON


    C136673E03
  1. Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Ensure that the 2 O-rings are not twisted.



    C138726
  1. Install the No. 2 brake piston to the transaxle case.

    NOTICE:
    Be careful not to damage the O-rings.



10. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
  1. Install the 1st and reverse brake return spring to the transaxle case.



    C137434E01
  1. Place SST on the 1st and reverse brake return spring and compress the 1st and reverse brake return spring using a press.

    SST
    09387-00060  

    NOTICE:
    Stop the press when the 1st and reverse brake return spring is flush with the snap ring groove. This prevents the 1st and reverse brake return spring from being deformed.

  1. Using a screwdriver, install the snap ring to the transaxle case as shown in the illustration.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case.
    2. Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case as shown in the illustration.



11. INSTALL NO. 2 BRAKE DISC


    C136483E02
  1. Install the 5 brake discs, 5 brake plates and brake flange to the transaxle case.
    Text in Illustration 
    *1
    Brake Flange
    *2
    Brake Plate
    *3
    Brake Disc

    NOTICE:
    Make sure that the discs, plates and flange are installed in the correct order.



    C136481
  1. Using a screwdriver, install the snap ring to the transaxle case.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case.
    2. Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case as shown in the illustration.



12. INSPECT CLEARANCE OF NO. 2 BRAKE


    C137439
  1. Using a dial indicator, measure the clearance of the No. 2 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

    Standard clearance:
    0.884 to 1.196 mm (0.0348 to 0.0471 in.)

    HINT:
    Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.

    If the clearance is not as specified, select an appropriate No. 2 brake flange so that the clearance will be within the specified range.

    HINT:
    There are 5 flanges of different thicknesses.

    No. 2 Brake Flange Thickness: mm (in.) 
    Mark
    Thickness
    40
    4.0 (0.157)
    41
    4.1 (0.161)
    42
    4.2 (0.165)
    43
    4.3 (0.169)
    44
    4.4 (0.173)



13. INSTALL PLANETARY RING GEAR FLANGE


    C136480E02
  1. Install the planetary ring gear flange to the planetary ring gear.
    Text in Illustration 
    *1
    Snap Ring
    *2
    Planetary Ring Gear Flange
    *3
    Planetary Ring Gear

  1. Using a screwdriver, install the snap ring to the planetary ring gear.

    NOTICE:
    Confirm that the snap ring is correctly located in the groove of the planetary ring gear.



14. INSTALL PLANETARY RING GEAR


    C136479E02
  1. Install the planetary ring gear to the one-way clutch assembly.
    Text in Illustration 
    *1
    One-way Clutch Assembly
    *2
    Planetary Ring Gear

    NOTICE:
    Make sure that the one-way clutch assembly is positioned in the correct direction as shown in the illustration.



15. INSTALL ONE-WAY CLUTCH ASSEMBLY


    C141546E02
  1. Coat the thrust needle roller bearing with ATF, and install it onto the planetary gear assembly.
    Text in Illustration 
    *1
    One-way Clutch Assembly
    *2
    Thrust Needle Roller Bearing
    Bearing Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    56.1 (2.21)
    80.9 (3.19)

    NOTICE:
    Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.

  1. Install the one-way clutch assembly to the transaxle case.

    NOTICE:
    Make sure that there is no clearance between the retainer and the claw on the one-way clutch assembly. If there is any clearance, the spring of the retainer will be deformed.



    C136477
  1. Using a screwdriver, install the snap ring to the transaxle case.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case.
    2. Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case as shown in the illustration.



16. INSTALL COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING OUTER RACE


    C194899E01
  1. Using SST and a hammer, install a new counter driven gear rear tapered roller bearing outer race to the transaxle case.

    SST
    09950-60010   (09951-00650)
    09950-70010   (09951-07100)

    NOTICE:
    Be sure to install the counter driven gear rear tapered roller bearing outer race so that there is no clearance between the bearing outer race and the transaxle case. If there is any clearance, the turning torque of the counter drive gear cannot be measured correctly.



17. INSTALL PARKING LOCK PAWL


    C136475E02
  1. Install the parking lock pawl to the transaxle case with the parking lock pawl shaft.
    Text in Illustration 
    *1
    Parking Lock Pawl Shaft
    *2
    Parking Lock Pawl
    *3
    Spring
    *4
    Parking Lock Pawl Pin

  1. Install the parking lock pawl pin to the transaxle case.



    C137444
  1. Install the spring to the parking lock pawl.

    NOTICE:
    Make sure that one end of the spring is set in the hole of the transaxle case and the other end is positioned on the parking lock pawl as shown in the illustration.



18. INSTALL PARKING LOCK SLEEVE


    C136474
  1. Install the parking lock sleeve to the transaxle case.



19. INSTALL PAWL STOPPER PLATE


    C136473
  1. Install the pawl stopper plate to the transaxle case with the 2 bolts.

    Torque:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }



20. INSTALL PAWL SHAFT CLAMP


    C136472
  1. Install the pawl shaft clamp to the transaxle case with the bolt.

    Torque:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }



21. INSTALL COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING


    C194897E01
  1. Using SST and a press, install a new counter driven gear rear tapered roller bearing to the counter driven gear sub-assembly.

    SST
    09950-60010   (09951-00420)

    NOTICE:
    Be sure to install the counter driven gear rear tapered roller bearing and the differential drive pinion so that there is no clearance between each of them and the counter driven gear.



22. INSTALL COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING


    C194896E01
  1. Using SST and a press, install a new counter driven gear front tapered roller bearing to the counter driven gear sub-assembly.

    SST
    09950-60010   (09951-00530)

    NOTICE:
    Be sure to install the counter driven gear front tapered roller bearing so that there is no clearance between the bearing and the counter driven gear. If there is any clearance, the turning torque of the counter drive gear cannot be measured correctly.



23. INSTALL COUNTER DRIVEN GEAR


    C136469
  1. Install the counter driven gear sub-assembly to the transaxle case.



24. INSTALL COUNTER DRIVE GEAR NUT


    C136700E01
  1. Turn the manual valve lever 2 notches counterclockwise to set it to the P position as shown in the illustration.



    C136468E01
  1. Using SST, install a new counter drive gear nut.

    SST
    09387-00130  

    Torque:
    120 N*m{ 1223 kgf*cm , 88 ft.*lbf }



    C136699E01
  1. Turn the manual valve lever 2 notches clockwise to set it to the N position as shown in the illustration.



    C138252E01
  1. Using SST and a torque wrench, measure the turning torque of the bearing while rotating SST at 60 rpm.

    SST
    09387-00130  

    Turning torque:
    0.1 to 0.2 N*m (1 to 2 kgf*cm, 0.9 to 1.9 in.*lbf)

    If the measured value is not within the specified range, gradually tighten the nut until the turning toque falls within the specified range.

    Maximum torque:
    180 N*m (1835 kgf*cm, 132 ft.*lbf)



    C136698E01
  1. Using SST and a hammer, stake the planetary gear assembly.

    SST
    09930-00010  



25. INSPECT DIFFERENTIAL SIDE GEAR BACKLASH


    C083562
  1. Hold the differential case in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Place a dial indicator at a right angle to one of the side gear teeth.

  1. Hold the pinion gear in the differential case and measure the backlash of the side gear.

    Standard backlash:
    0.05 to 0.15 mm (0.00197 to 0.00591 in.)

    Thrust Washer Thickness 
    Thickness
    Thickness
    1.50 mm (0.0591 in.)
    1.75 mm (0.0689 in.)
    1.55 mm (0.0610 in.)
    1.80 mm (0.0709 in.)
    1.60 mm (0.0630 in.)
    1.85 mm (0.0728 in.)
    1.65 mm (0.0650 in.)
    1.90 mm (0.0748 in.)
    1.70 mm (0.0669 in.)
    -
    If the backlash is not within the standard range, select another side gear thrust washer.



26. INSTALL FRONT DIFFERENTIAL CASE


    C136467
  1. Install the front differential case to the transaxle case.



27. INSTALL NO. 1 BRAKE PISTON


    C136466E03
  1. Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Ensure that the O-rings are not twisted.



    C138253
  1. Install the No. 1 brake piston to the oil pump assembly.

    NOTICE:
    Be careful not to damage the O-rings.



28. INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C136464
  1. Install the 3 2nd brake piston return springs to the oil pump assembly.

    NOTICE:
    Make sure that the 3 2nd brake piston return springs are installed onto the protrusions on the oil pump assembly.



29. INSTALL NO. 1 BRAKE DISC


    C141545E02
  1. Install the 4 No. 1 brake discs, 4 No. 1 brake plates and No. 1 brake flange to the oil pump assembly.
    Text in Illustration 
    *1
    No. 1 Brake Flange
    *2
    No. 1 Brake Plate
    *3
    No. 1 Brake Disc

    NOTICE:
    1. Make sure that the discs, plates, and flange are installed in the correct order.
    2. Be sure to install the flange in the correct direction.

  1. Place SST on the flange and compress the flange using a press.

    SST
    09387-00070  
    09495-65040  

    NOTICE:
    Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.



    C189783E01
  1. Using a screwdriver, install the snap ring to the oil pump assembly as shown in the illustration (#1).

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the oil pump.
    2. Make sure to align the protruding part of the snap ring with the indented part (#1) of the front oil pump assembly shown in the illustration to install the snap ring.



    C176220
  1. Install the brake snap ring stopper to the oil pump assembly.

    NOTICE:
    Be sure to install the brake snap ring stopper in the correct direction.



    C189784E01
  1. Using a screwdriver, install the snap ring to the oil pump assembly as shown in the illustration (#2).

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the oil pump.
    2. Make sure to align the protruding part of the snap ring with the indented part (#2) of the front oil pump assembly shown in the illustration to install the snap ring.



    C153481E04
  1. Check that the brake snap ring stopper can be turned by hand.
    Text in Illustration 
    *1
    Snap Ring
    *2
    Brake Snap Ring Stopper
    *a
    Correctly installed

    NOTICE:
    If the brake snap ring stopper cannot be turned by hand, the brake snap ring stopper may have been installed upside down, or the snap ring may not have been completely located in the groove on the oil pump. Remove and reinstall the snap ring and the brake snap ring stopper.



30. INSPECT CLEARANCE OF NO. 1 BRAKE


    C138258
  1. Using a dial indicator, measure the clearance of the No. 1 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

    Standard clearance:
    0.807 to 0.974 mm (0.0318 to 0.0383 in.)

    HINT:
    Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.

    If the clearance is not as specified, select an appropriate No. 1 brake flange so that the clearance will be within the specified range.

    HINT:
    There are 6 flanges of different thicknesses.

    No. 1 Brake Flange Thickness: mm (in.) 
    Mark
    Thickness
    30
    3.0 (0.118)
    31
    3.1 (0.122)
    32
    3.2 (0.126)
    33
    3.3 (0.130)
    34
    3.4 (0.134)
    35
    3.5 (0.138)



31. INSTALL UNDERDRIVE PLANETARY SUN GEAR


    C141538E01
  1. Coat the thrust needle roller bearing with ATF, and install it to the oil pump assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Underdrive Planetary Sun Gear
    Bearing Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    57.7 (2.27)
    75.2 (2.96)

    NOTICE:
    Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.

  1. Install the underdrive planetary sun gear to the oil pump assembly.



32. INSTALL INPUT SHAFT SUB-ASSEMBLY


    C141539E02
  1. Coat 3 new input shaft oil seal rings with ATF and install them to the input shaft.
    Text in Illustration 
    *1
    Thrust Needle Roller Race
    *2
    Thrust Needle Roller Bearing
    *3
    Input Shaft Oil Seal Ring
    *4
    Input Shaft

    NOTICE:
    Do not expand the gap of the oil seal ring excessively.

  1. Coat the thrust needle roller bearing and thrust needle roller race with ATF, and install them on the oil pump assembly.
    Bearing and Race Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    29.1 (1.15)
    48.6 (1.91)
    Race
    30.7 (1.21)
    48.3 (1.90)

    NOTICE:
    Be sure to install the thrust needle roller bearing in the correct direction.



    C136459
  1. Install the input shaft to the oil pump assembly.



33. INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY


    C136457E02
  1. Using a snap ring expander, install the snap ring to the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Planetary Sun Gear Sub-assembly
    *2
    Underdrive Planetary Gear Assembly
    *3
    Snap Ring

  1. Using a snap ring expander, install the planetary sun gear sub-assembly to the underdrive planetary gear assembly with the snap ring expanded.



34. INSTALL UNDERDRIVE PLANETARY RING GEAR


    C136456E03
  1. Install the underdrive planetary ring gear to the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Snap Ring
    *2
    Underdrive Planetary Ring Gear

  1. Using needle-nose pliers, install the snap ring to the underdrive planetary ring gear.

    NOTICE:
    Confirm that the snap ring is correctly located in the groove of the underdrive planetary ring gear.



35. INSTALL NO. 3 BRAKE HUB


    C141540E02
  1. Coat the thrust needle roller bearing with ATF and install it on the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    Bearing and Race Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    62.6 (2.46)
    82.9 (3.26)
    Race
    65.9 (2.59)
    80.3 (3.16)

    NOTICE:
    Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



    C141537E02
  1. Coat the thrust needle roller race with MP grease and install it to the No. 3 brake hub.
    Text in Illustration 
    *1
    Thrust Needle Roller Race



    C136454
  1. Install the No. 3 brake hub to the underdrive planetary gear assembly.



36. INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY


    C136458
  1. Install the underdrive planetary gear assembly to the oil pump assembly.



37. INSTALL NO. 3 BRAKE DISC


    C136452E02
  1. Install the 2 No. 3 brake flanges, 3 No. 3 brake discs and 2 No. 3 brake plates to the oil pump assembly.
    Text in Illustration 
    *1
    No. 3 Brake Flange
    *2
    No. 3 Brake Plate
    *3
    No. 3 Brake Disc

    NOTICE:
    Make sure that the discs, plates and flanges are installed in the correct order.



    C136451E02
  1. Using a screwdriver, install the snap ring to the oil pump assembly.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the oil pump.
    2. Make sure that the snap ring ends are positioned as shown in the illustration (A).



38. INSPECT CLEARANCE OF NO. 3 BRAKE


    C138724E04
  1. Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension A) while a load of 500 N (51 kgf, 112.4 lbf) is being applied to the flange.
    Text in Illustration 
    *1
    Front Oil Pump Assembly
    *2
    No. 3 Brake Piston
    *a
    Dimension A
    *b
    Dimension B
    *c
    Contact surface of front oil pump assembly

    HINT:
    Measure dimension A at 3 points where the flange diameter is approximately 166 mm (6.54 in.) and calculate the average.

  1. Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).

    HINT:
    Measure dimension B at 3 points where the No. 3 brake diameter is approximately 166 mm (6.54 in.) and calculate the average.

  1. Calculate the clearance value using the following formula:
    Clearance = Dimension B - Dimension A

    Standard clearance:
    0.599 to 0.761 mm (0.0236 to 0.0300 in.)

    If the clearance is not as specified, select an appropriate brake flange so that the clearance will be within the specified range.

    HINT:
    There are 6 flanges of different thicknesses.

    No. 3 Brake Flange Thickness: mm (in.) 
    Mark
    Thickness
    38
    3.80 (0.150)
    39
    3.90 (0.154)
    40
    4.00 (0.157)
    41
    4.10 (0.161)
    42
    4.20 (0.165)
    43
    4.30 (0.169)



39. INSTALL FRONT OIL PUMP ASSEMBLY


    C141541E02
  1. Coat a new O-ring with ATF and install it to the transaxle case.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Needle Roller Race
    *3
    O-ring

  1. Coat the thrust needle roller bearing and thrust needle roller race with ATF and install them on the underdrive planetary gear assembly.
    Bearing and Race Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    53.1 (2.09)
    79 (3.11)
    Race
    59.4 (2.34)
    77 (3.03)

    NOTICE:
    Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



    C136450E02
  1. Coat a new O-ring with ATF and install it to the oil pump.
    Text in Illustration 
    *1
    O-ring

  1. Install the oil pump assembly to the transaxle case with the 7 bolts.

    Torque:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }



40. INSTALL FRONT OIL PUMP BODY O-RING


    C138278
  1. Coat a new O-ring with ATF and install it to the front oil pump body sub-assembly.



41. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE


    C136449E01
  1. Install the differential gear lube apply tube to the transaxle housing.

    NOTICE:
    Insert the differential gear lube apply tube into the transaxle case until it makes contact with the stopper.

  1. Install the apply tube clamp to the differential gear lube apply tube with the bolt.

    Torque:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }

    NOTICE:
    There should be clearance between the differential lube apply tube and apply tube clamp.



42. INSTALL COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING OUTER RACE


    C194900E01
  1. Install the shim to the transaxle housing.

  1. Using SST, install a new counter driven gear front tapered roller bearing outer race to the transaxle housing.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07100)

    NOTICE:
    Be sure to install the counter driven gear front tapered roller bearing outer race so that there is no clearance between the shim and the transaxle housing.



43. INSTALL TRANSAXLE HOUSING
  1. Remove any packing material from the contact surfaces between the transaxle housing and case.

    NOTICE:
    Make sure that there is no ATF on the contact surfaces.



    C138263E04
  1. Apply FIPG to the transaxle case.
    Text in Illustration 
    *a
    FIPG

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    Apply FIPG in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.



    C136447E02
  1. Install the transaxle housing to the transaxle case with the 20 bolts.

    Torque:
    Bolt A:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }
    Bolt B:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }



44. ADJUST COUNTER DRIVEN GEAR PRELOAD


    C138262E01
  1. Using SST and a torque wrench, measure the turning torque of the counter driven gear while rotating SST at 10 rpm.

    SST
    09564-33010  

    Turning torque:
    Differential side bearing preload 3.3 to 6.0 N*m (34 to 61 kgf*cm, 29 to 53 in.*lbf)

    If the turning torque is not within the specified range, refer to the table below to select a shim of the counter driven gear front tapered roller bearing outer race so that the turning torque is within the specified range.
    Shim Thickness: mm (in.) 
    Thickness
    Thickness
    Thickness
    Thickness
    2.000 (0.0787)
    2.275 (0.0896)
    2.525 (0.0994)
    2.775 (0.109)
    2.025 (0.0797)
    2.300 (0.0906)
    2.550 (0.100)
    2.800 (0.110)
    2.050 (0.0807)
    2.325 (0.0915)
    2.575 (0.101)
    2.825 (0.111)
    2.075 (0.0817)
    2.350 (0.0925)
    2.600 (0.102)
    2.850 (0.112)
    2.100 (0.0827)
    2.375 (0.0935)
    2.625 (0.103)
    2.875 (0.113)
    2.125 (0.0837)
    2.400 (0.0945)
    2.650 (0.104)
    2.900 (0.114)
    2.150 (0.0846)
    2.425 (0.0955)
    2.675 (0.105)
    2.925 (0.115)
    2.175 (0.0856)
    2.450 (0.0965)
    2.700 (0.106)
    2.950 (0.116)
    2.200 (0.0866)
    2.475 (0.0974)
    2.725 (0.107)
    2.975 (0.117)
    2.225 (0.0876)
    2.500 (0.0984)
    2.750 (0.108)
    3.000 (0.118)
    2.250 (0.0886)
    -
    -
    -



45. INSTALL NO. 1 CLUTCH DISC


    C136446E03
  1. Install the clutch flange, 4 clutch discs and 4 clutch plates to the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Clutch Flange
    *2
    Clutch Plate
    *3
    Clutch Disc

    NOTICE:
    Make sure that the flange, discs and plates are installed in the correct order.



    C136445
  1. Using a screwdriver, install the 2 snap rings to the direct multiple disc clutch assembly.

    NOTICE:
    Confirm that the snap rings are correctly located in the groove of the direct multiple disc clutch assembly.



46. INSPECT CLEARANCE OF NO. 1 CLUTCH DISC


C239101E01

NOTICE:
There are two different types of rear multiple disc clutch assembly. Refer to the illustration and visually inspect the rear multiple disc clutch assembly to determine if it is transaxle serial number 2########## or transaxle serial number 3##########.

Text in Illustration 
*a
Transaxle serial number 2##########
*b
Transaxle serial number 3##########


    C138728
  1. Install the direct multiple disc clutch assembly onto the rear transaxle cover sub-assembly.

  1. Using a dial indicator, measure the No. 1 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

    HINT:
    Measure the clearance at 3 points where the flange diameter is approximately 152 mm (5.98 in.) and calculate the average.

    Pack clearance:
    0.606 to 0.774 mm (0.0238 to 0.0305 in.)

    If the pack clearance is not as specified, select an appropriate No. 1 clutch flange so that the pack clearance will be within the specified range.

    HINT:
    There are 7 flanges of different thicknesses.

    No. 1 Clutch Flange Thickness: mm (in.) 
    Mark
    Thickness
    30
    3.0 (0.118)
    31
    3.1 (0.122)
    32
    3.2 (0.126)
    33
    3.3 (0.130)
    34
    3.4 (0.134)
    35
    3.5 (0.138)
    36*
    3.6 (0.142)*

    HINT:
    *Transaxle serial number 3########## only



47. INSTALL REAR PLANETARY SUN GEAR ASSEMBLY


    C141542E02
  1. Coat the thrust needle roller bearing and thrust needle roller race with ATF, and install them to the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Needle Roller Race
    Bearing and Race Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    28 (1.10)
    47.1 (1.85)
    Race
    26.1 (1.03)
    44 (1.73)

    NOTICE:
    Install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



    C136437
  1. Install the rear planetary sun gear assembly to the direct multiple disc clutch assembly.



    C136436
  1. Using a snap ring expander, install the snap ring to the direct multiple disc clutch assembly.



48. INSTALL NO. 2 CLUTCH DISC


    C136435E03
  1. Install the clutch flange, 3 clutch discs and 3 clutch plates to the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Clutch Plate
    *2
    Clutch Disc
    *3
    Clutch Flange

    NOTICE:
    Make sure that the flange, discs and plates are installed in the correct order.



49. INSTALL DIRECT MULTIPLE DISC CLUTCH SNAP RING


    C136428E04
  1. Coat a new O-ring with ATF and install it to the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Intermediate Shaft Oil Seal
    *2
    O-ring

  1. Coat a new intermediate shaft oil seal with ATF and install it to the direct multiple disc clutch assembly.



    C141535
  1. Install the No. 2 direct clutch piston to the direct multiple disc clutch assembly.

    NOTICE:
    Be sure to engage the claws on the direct multiple disc clutch assembly in the grooves on the No. 2 direct clutch piston.



    C136433E01
  1. Using a screwdriver, install the snap ring to the direct multiple disc clutch assembly.

    NOTICE:
    1. Position the opening of the snap ring as shown in the illustration.
    2. Confirm that the snap ring is correctly located in the groove of the direct multiple disc clutch assembly.



50. INSPECT CLEARANCE OF NO. 2 CLUTCH DISC


    C138727
  1. Install the direct multiple disc clutch assembly onto the rear transaxle cover sub-assembly.

  1. Using a dial indicator, measure the No. 2 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

    HINT:
    Measure the clearance at 3 points where the diameter of the No. 2 direct multiple clutch piston is approximately 152 mm (5.98 in.) and calculate the average.

    Pack clearance:
    0.544 to 0.744 mm (0.0214 to 0.0293 in.)

    If the pack clearance is not as specified, select an appropriate No. 2 clutch flange so that the pack clearance will be within the specified range.

    HINT:
    There are 7 flanges of different thicknesses.

    No. 2 Clutch Flange Thickness: mm (in.) 
    Mark
    Thickness
    30
    3.0 (0.118)
    31
    3.1 (0.122)
    32
    3.2 (0.126)
    33
    3.3 (0.130)
    34
    3.4 (0.134)
    35
    3.5 (0.138)
    36*
    3.6 (0.142)*

    HINT:
    *Transaxle serial number 3########## only



51. INSTALL DIRECT MULTIPLE DISC CLUTCH ASSEMBLY


    C141543E01
  1. Coat the thrust needle roller bearing with ATF and install it on the transaxle case.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Direct Multiple Disc Clutch Assembly
    Bearing Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    61.2 (2.41)
    79 (3.11)

  1. Install the direct multiple disc clutch assembly to the transaxle case.

  1. Clean the contact surfaces of the transaxle case and rear transaxle cover sub-assembly.



    C138269E03
  1. As shown in the illustration, place a straightedge on the multiple direct clutch drum and measure the distance between the transaxle case and the straightedge using a vernier caliper (Dimension A).
    Text in Illustration 
    *a
    Dimension A



    C138268E04
  1. Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).
    Text in Illustration 
    *a
    Dimension B

  1. Calculate the end play value using the following formula:
    End play = Dimension B - Dimension A - Thrust needle roller bearing thickness

    End play:
    0.007 to 1.113 mm (0.000275 to 0.0438 in.)



52. INSTALL REAR TRANSAXLE COVER SUB-ASSEMBLY


    C194898E01
  1. Using SST and a hammer, install a new needle roller bearing into the rear transaxle cover sub-assembly.

    SST
    09950-60010   (09951-00220)
    09950-70010   (09951-07100)

    Installation depth:
    21.5 to 21.9 mm (0.846 to 0862 in.)

  1. Apply adhesive to the 2 "TORX" screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    C162442E01
  1. Using a "TORX" socket wrench (T30), install the rear transaxle cover plate to the rear transaxle cover sub-assembly with the 2 "TORX" screws.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    C141544E02
  1. Coat the thrust needle roller bearing and thrust needle roller race with ATF and install them on the transaxle case.
    Text in Illustration 
    *1
    Oil Seal Ring
    *2
    Thrust Needle Roller Bearing
    *3
    Thrust Needle Roller Race
    Bearing and Race Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    48.9 (1.93)
    72.0 (2.84)
    Race
    52.2 (2.06)
    70.4 (2.77)

  1. Coat 2 new oil seal rings with ATF and install them to the rear transaxle cover sub-assembly.



    C136432E01
  1. Coat 3 new O-rings with ATF and install them to the transaxle case.

    NOTICE:
    Ensure that the O-rings are not twisted.



    C138271
  1. Remove packing material from the contact surfaces between the rear transaxle cover sub-assembly and transaxle case.

    NOTICE:
    Make sure that there is no ATF on the contact surfaces.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



    C162440E01
  1. Install the rear transaxle cover sub-assembly to the transaxle case with the 14 bolts.

    Torque:
    Bolt A:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }
    Bolt B:
    17 N*m{ 173 kgf*cm , 12 ft.*lbf }



    C162439
  1. Install a new gasket to the refill plug.

  1. Install the refill plug to the rear transaxle cover sub-assembly.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



    C134960
  1. Coat 2 new O-rings with ATF and install them to the 2 No. 1 automatic transaxle case plugs.

  1. Install the 2 No. 1 automatic transaxle case plugs to the rear transaxle cover sub-assembly.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



53. INSPECT INPUT SHAFT END PLAY


    C136696
  1. Using a dial indicator, measure the input shaft end play.

    End play:
    0.012 to 1.250 mm (0.000473 to 0.0492 in.)



54. INSTALL TRANSAXLE CASE GASKET


    C136429E01
  1. Coat 2 new gaskets with ATF and install them to the transaxle case.



55. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


    C136689E01
  1. Install the valve body assembly to the transaxle case with the 11 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    -
    -
    Bolt Length
    Bolt Length
    Bolt A
    25 mm (0.984 in.)
    Bolt B
    30 mm (1.18 in.)
    Bolt C
    35 mm (1.38 in.)
    Bolt D
    45 mm (1.77 in.)
    Bolt E
    55 mm (2.17 in.)

    NOTICE:
    1. When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case to interfere with each other.
    2. Be sure to insert the pin of the manual valve lever into the groove on the end of the manual valve.
    3. First, temporarily tighten the bolts marked by *1 in the illustration because they are positioning bolts.



56. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


    C136688E05
  1. Coat a new O-ring with ATF and install it to the oil strainer assembly.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Ensure that the O-ring is not twisted or pinched.



    C136687
  1. Install the oil strainer assembly to the valve body assembly with the 2 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



57. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    C134963E04
  1. Install the 2 magnets in the automatic transaxle oil pan sub-assembly.
    Text in Illustration 
    *1
    Magnet

  1. Install a new gasket to the oil pan.



    C243139
  1. Install the oil pan to the automatic transaxle with the 17 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    C243140
  1. Clean and degrease the bolt and the installation hole in the automatic transaxle.

  1. Apply adhesive to the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    1. In order to ensure proper sealing of the transmission oil pan bolts, apply adhesive to the bolts and install them within 10 minutes of adhesive application.
    2. Completely remove any oil or grease from the contact surface of the transaxle case and oil pan sub-assembly with the gasket before installation.



    C141531
  1. Using a hexagon socket wrench (6 mm), install the No. 1 oil filler tube to the automatic transaxle assembly.

    Torque:
    1.7 N*m{ 17 kgf*cm , 15 in.*lbf }



    C134961
  1. Using a hexagon socket wrench (6 mm), install the overflow plug and a new gasket to the oil pan sub-assembly.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



58. INSTALL NO. 1 TRANSAXLE CASE PLUG
  1. Install 3 new gaskets to the 3 hexagon bolts.

  1. Apply adhesive to the 3 hexagon bolts.

    Adhesive:
    Toyota Genuine Seal Packing 1344, Three Bond 1344 or equivalent

    NOTICE:
    In order to ensure proper sealing of the hexagon bolts, apply adhesive to the bolts and install them within 10 minutes of adhesive application.



    C134959
  1. Using a hexagon socket wrench (6 mm), install the 3 hexagon bolts to the transaxle housing with the gaskets.

    Torque:
    17 N*m{ 173 kgf*cm , 12 ft.*lbf }



    C162438
  1. Coat 3 new O-rings with ATF and install them to the 3 No. 1 transaxle case plugs.

  1. Install the 3 No. 1 transaxle case plugs to the transaxle case.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



59. INSTALL OIL COOLER TUBE UNION (INLET OIL COOLER UNION)


    C239679
  1. Coat a new O-ring with ATF and install it to the oil cooler tube union (inlet oil cooler union).

  1. Install the oil cooler tube union (inlet oil cooler union) to the transaxle case.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



60. INSTALL OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)


    C239730
  1. Coat a new O-ring with ATF and install it to the oil cooler tube union (outlet oil cooler union).

  1. Install the oil cooler tube union (outlet oil cooler union) to the transaxle case.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



61. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C135733E11
  1. Align the protrusions of the park/neutral position switch.
    Text in Illustration 
    *a
    Protrusion



    C136686
  1. Install the park/neutral position switch to the control shaft with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    1. Before installing the park/neutral position switch, remove any dirt or rust on the control shaft. Be sure to install the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch cannot be reinstalled correctly.
    2. After installing the park/neutral position switch, confirm that the 2 protrusions on the switch are aligned.



    C136685
  1. Install the control shaft lever to the control shaft with the washer and nut.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



62. INSTALL BREATHER PLUG HOSE


    C134952E04
  1. Coat a new O-ring with ATF and install it to the No. 2 breather plug (ATM).
    Text in Illustration 
    *1
    No. 1 Breather Plug (ATM)
    *2
    Breather Plug Hose
    *3
    No. 2 Breather Plug (ATM)
    *4
    O-ring

  1. Install the No. 1 breather plug (ATM) and No. 2 breather plug (ATM) to the breather plug hose.



    C190663
  1. Install the breather plug hose to the transaxle case.