Home › Power Source / Network · NETWORKING › LIN COMMUNICATION SYSTEM

LIN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


  1. Disconnect the MB and 3D instrument panel junction block assembly connectors.


    B278841E31

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3D-31 (BECU) - Body ground
    V - Body ground
    Battery power supply
    Always
    11 to 14 V
    MB-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the MB and 3D instrument panel junction block assembly connectors.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3B-30 (LIN2) - 3B-7 (GND1)
    P - W-B
    LIN communication line
    Ignition switch ON
    Pulse generation
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may be malfunctioning.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)


  1. Disconnect the K9 power window regulator motor assembly (for driver side) connector.


    B270965E15

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K9-2 (B) - K9-1 (E)
    W - W-B
    Battery power supply
    Always
    11 to 14 V
    K9-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the K9 power window regulator motor assembly (for driver side) connector.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K9-9 (LIN) - K9-1 (E)
    P - W-B
    LIN communication line
    Ignition switch ON
    Pulse generation
    If the result is not as specified, the power window regulator motor assembly (for driver side) may be malfunctioning.


CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (w/ Sliding Roof System)


  1. Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


    B270994E01

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S4-8 (B) - S4-12 (E)
    B - W-B
    Battery power supply
    Always
    11 to 14 V
    S4-12 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.

  4. Check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S4-11 (MPX1) - S4-12 (E)
    P - W-B
    LIN communication line
    Ignition switch ON
    Pulse generation
    If the result is not as specified, the sliding roof ECU (sliding roof drive gear sub-assembly) may be malfunctioning.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


  1. Disconnect the A43 certification ECU (smart key ECU assembly) connector.


    B264892E30

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A43-2 (+B) - A43-11 (E)
    W - W
    Battery power supply
    Always
    11 to 14 V
    A43-11 (E) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the A43 certification ECU (smart key ECU assembly) connector.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I78-5 (IG) - A43-11 (E)
    LG - W
    IG power supply
    Ignition switch ON
    11 to 14 V
    I78-5 (IG) - A43-11 (E)
    LG - W
    IG power supply
    Ignition switch off
    Below 1 V
    I78-17 (LIN) - A43-11 (E)
    V - W
    LIN communication line
    Ignition switch ON
    Pulse generation
    If the result is not as specified, the certification ECU (smart key ECU assembly) may be malfunctioning.


CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)


    C211401E16
  1. Disconnect the I24 steering lock ECU (steering lock actuator assembly) connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I24-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    I24-7 (B) - Body ground
    B - Body ground
    Battery power supply
    Always
    11 to 14 V
    I24-6 (IG2) - Body ground
    LG - Body ground
    IG power supply
    Ignition switch ON
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the I24 steering lock ECU (steering lock actuator assembly) connector.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I24-5 (LIN) - I24-1 (GND)
    V - W-B
    LIN communication line
    Ignition switch ON
    Pulse generation
    If the result is not as specified, the steering lock ECU (steering lock actuator assembly) may be malfunctioning.