Home › Power Source / Network · NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B2321    Driver Side Door ECU Communication Stop

for Preparation Click here


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (for driver side) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No.
DTC Detection Condition
Trouble Area
B2321
No communication between power window regulator motor assembly (for driver side) and main body ECU (multiplex network body ECU) for 10 seconds or more.
  1. Power window regulator motor assembly (for driver side)
  2. Main body ECU (multiplex network body ECU)
  3. Wire harness or connector
  4. DOOR No. 2 fuse

WIRING DIAGRAM


B274860E08


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When the power window regulator motor assembly (for driver side) is replaced or removed and reinstalled, it requires initialization (Click here).
  3. When using the Techstream to troubleshoot with the ignition switch off:
    Connect the Techstream to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.

1.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)
  1. Disconnect the 3B instrument panel junction block assembly connector.

  1. Disconnect the K9 power window regulator motor (for driver side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-30 (LIN2) - K9-9 (LIN)
    Always
    Below 1 Ω
    3B-30 (LIN2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Remove the instrument panel junction block assembly (Click here).


    B274862E03

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3B-30 (LIN2) - MB-16 (LIN2)
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    *b
    Component without harness connected
    (Instrument Panel Junction Block Assembly)



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - BATTERY, BODY GROUND)


    E175952E08
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    K9-2 (B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K9-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER SIDE)
  1. Replace the power window regulator motor assembly (for driver side) (Click here).


NEXT


5.CHECK DTC OUTPUT
  1. Clear the DTC (Click here).

  1. Check for DTCs.

    OK:
    DTC B2321 is not output.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY WAS DEFECTIVE)