AUTOMATIC TRANSAXLE SYSTEM > Shift Paddle Switch Circuit |

| 1.READ VALUE USING TECHSTREAM (SPORT SHIFT SWITCH STATUS) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
In accordance with the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Sports Shift Up SW | Sport shift up switch status/ ON or OFF |
| - |
| Sports Shift Down SW | Sport shift down switch status/ ON or OFF |
| - |
| Result | Proceed to |
| Data display is not within Normal Condition range | A |
| Data display is within Normal Condition range | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (SHIFT PADDLE SWITCH CIRCUIT) |
![]() |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A25- 43 (SFTD) - Body ground | Pull "-" continuously (Down-shift) | Below 1 Ω |
| Release | 10 kΩ or higher | |
| A25-42 (SFTU) - Body ground | Pull "+" continuously (Up-shift) | Below 1 Ω |
| Release | 10 kΩ or higher |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BODY GROUND) |
Disconnect the negative (-) terminal cable from the battery.
Wait for at least 90 seconds.
Remove the steering wheel assembly.
Remove the steering column cover.
![]() |
Disconnect the spiral cable connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I28-2 (ECC) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Spiral Cable Sub-assembly) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A25-43 (SFTD) - I28-7 (SDN) | Always | Below 1 Ω |
| A25-43 (SFTD) or I28-7 (SDN) - Body ground | Always | 10 kΩ or higher |
| A25-42 (SFTU) - I28-14 (SUP) | Always | Below 1 Ω |
| A25-42 (SFTU) or I28-14 (SUP) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - SHIFT PADDLE SWITCH) |
Remove the horn button assembly.
Disconnect the steering pad switch connector from the spiral cable sub-assembly.
![]() |
Measure the resistance according to the value(s) in the table below when the shift paddle switch is moved to each position.
| Tester Connection | Switch Condition | Specified Condition |
| z3-6 (SUP) - z3-7 (ECC) | Pull "+" continuously (Up-shift) | Below 1 Ω |
| Release | 10 kΩ or higher | |
| z3-12 (SDN) - z3-7 (ECC) | Pull "-" continuously (Down-shift) | Below 1 Ω |
| Release | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Spiral Cable Sub-assembly) |
|
| ||||
| OK | |
| 6.INSPECT SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Disconnect the steering pad switch connector from the spiral cable sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z3-7 (ECC) - I28-2 (ECC) | Always | Below 3 Ω |
| z3-6 (SUP) - I28-14 (SUP) | Always | Below 3 Ω |
| z3-12 (SDN) - I28-7 (SDN) | Always | Below 3 Ω |
| z3-7 (ECC) or I28-2 (ECC) - All other terminals | Always | 10 kΩ or higher |
| z3-6 (SUP) or I28-14 (SUP) - All other terminals | Always | 10 kΩ or higher |
| z3-12 (SDN) or I28-7 (SDN) - All other terminals | Always | 10 kΩ or higher |
| *a | Component without harness connected (Spiral Cable Sub-assembly) |
| *b | Steering Pad Switch Side |
| *c | Vehicle Side |
|
| ||||
| OK | ||
| ||
| 7.INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY (SHIFT PADDLE SWITCH) |
![]() |
Disconnect the connector from the transmission shift switch LH and RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C-3 (ECC) - C-2 (SFTD) | Pull "-" continuously (Down-shift) | Below 1 Ω |
| Release | 10 kΩ or higher | |
| C-4 (ECC1) - C-2 (SFTD) | Pull "-" continuously (Down-shift) | Below 1 Ω |
| Release | 10 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
| B-3 (SFTU) - B-2 (ECC1) | Pull "+" continuously (Up-shift) | Below 1 Ω |
| Release | 10 kΩ or higher |
| *a | Component without harness connected (Shift paddle switch LH) |
| *b | Component without harness connected (Shift paddle switch RH) |
|
| ||||
| OK | |
| 8.INSPECT NO. 1 SWITCH WIRE |
Connect the transmission shift switch LH and RH connector.
![]() |
Disconnect the No.1 switch wire from steering pad switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A-3 (SFTD) - A-7 (ECC) | Pull "-" continuously (Down-shift) | Below 1 Ω |
| Release | 10 kΩ or higher | |
| A-2 (SFTU) - A-7 (ECC) | Pull "+" continuously (Down-shift) | Below 1 Ω |
| Release | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Steering Pad Switch Connector) |
|
| ||||
| OK | ||
| ||