Home › Drivetrain · U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

AUTOMATIC TRANSAXLE SYSTEM > Shift Paddle Switch Circuit

for Preparation Click here


DESCRIPTION

Moving the shift lever to S enables gear selection. The driver can select the gear optionally by shifting the paddle to "+" or "-".

WIRING DIAGRAM


C239279E03


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SHIFT PADDLE SWITCH CIRCUIT)


    C233487E14
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A25- 50 (SFTD) - Body ground
    Pull "-" continuously
    (Down-shift)
    Below 1 Ω
    Release
    10 kΩ or higher
    A25-34 (SFTU) - Body ground
    Pull "+" continuously
    (Up-shift)
    Below 1 Ω
    Release
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
Go to step 2
OK

GO TO TRANSMISSION CONTROL SWITCH CIRCUIT (Click here)  

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BODY GROUND)
  1. Disconnect the negative (-) terminal cable from the battery.

  1. Wait for at least 90 seconds.

  1. Remove the steering wheel assembly.

  1. Remove the steering column cover.



    C136967E01
  1. Disconnect the spiral cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I28-2 (ECC) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Spiral Cable Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A25-50 (SFTD) - I28-7 (SDN)
    Always
    Below 1 Ω
    A25-50 (SFTD) or I28-7 (SDN) - Body ground
    Always
    10 kΩ or higher
    A25-34 (SFTU) - I28-14 (SUP)
    Always
    Below 1 Ω
    A25-34 (SFTU) or I28-14 (SUP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - SHIFT PADDLE SWITCH)


    C245153E01
  1. Remove the horn button assembly.

  1. Disconnect the steering pad switch connector from the spiral cable sub-assembly.

  1. Measure the resistance according to the value(s) in the table below when the shift paddle switch is moved to each position.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    z3-6 (SUP) - z3-7 (ECC)
    Pull "+" continuously
    (Up-shift)
    Below 1 Ω
    Release
    10 kΩ or higher
    z3-12 (SDN) - z3-7 (ECC)
    Pull "-" continuously
    (Down-shift)
    Below 1 Ω
    Release
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Spiral Cable Sub-assembly)



NG
Go to step 6
OK


5.INSPECT SPIRAL CABLE SUB-ASSEMBLY


    C249692E01
  1. Disconnect the steering pad switch connector from the spiral cable sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-7 (ECC) - I28-2 (ECC)
    Always
    Below 3 Ω
    z3-6 (SUP) - I28-14 (SUP)
    Always
    Below 3 Ω
    z3-12 (SDN) - I28-7 (SDN)
    Always
    Below 3 Ω
    z3-7 (ECC) or I28-2 (ECC) - All other terminals
    Always
    10 kΩ or higher
    z3-6 (SUP) or I28-14 (SUP) - All other terminals
    Always
    10 kΩ or higher
    z3-12 (SDN) or I28-7 (SDN) - All other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Spiral Cable Sub-assembly)
    *b
    Steering Pad Switch Side
    *c
    Vehicle Side



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

6.INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY (SHIFT PADDLE SWITCH)


    C207558E08
  1. Disconnect the connector from the transmission shift switch LH and RH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Transmission Shift Switch LH: 
    Tester Connection
    Switch Condition
    Specified Condition
    C-3 (ECC) - C-2 (SFTD)
    Pull "-" continuously
    (Down-shift)
    Below 1 Ω
    Release
    10 kΩ or higher
    C-4 (ECC1) - C-2 (SFTD)
    Pull "-" continuously
    (Down-shift)
    Below 1 Ω
    Release
    10 kΩ or higher
    Transmission Shift Switch RH: 
    Tester Connection
    Switch Condition
    Specified Condition
    B-3 (SFTU) - B-2 (ECC1)
    Pull "+" continuously
    (Up-shift)
    Below 1 Ω
    Release
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Shift paddle switch LH)
    *b
    Component without harness connected
    (Shift paddle switch RH)



NG
REPLACE TRANSMISSION SHIFT SWITCH ASSEMBLY (SHIFT PADDLE SWITCH) (Click here)
OK


7.INSPECT NO. 1 SWITCH WIRE
  1. Connect the transmission shift switch LH and RH connector.



    C245155E01
  1. Disconnect the No.1 switch wire from steering pad switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A-3 (SFTD) - A-7 (ECC)
    Pull "-" continuously
    (Down-shift)
    Below 1 Ω
    Release
    10 kΩ or higher
    A-2 (SFTU) - A-7 (ECC)
    Pull "+" continuously
    (Down-shift)
    Below 1 Ω
    Release
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Pad Switch Connector)



NG
REPLACE NO. 1 SWITCH WIRE (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 SWITCH WIRE - SPIRAL CABLE SUB-ASSEMBLY)