Home › Engine / Hybrid System · 2GR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P050B    Cold Start Ignition Timing Performance

for Preparation Click here


MONITOR DESCRIPTION

This monitor will run when the engine is started at an engine coolant temperature of -10 to 50°C (14 to 122°F). The DTC is stored after the engine idles for 13 seconds (2 trip detection logic).
The DTC is designed to monitor the ignition timing at cold start. When the engine is started at an engine coolant temperature of less than 50°C (122°F), the ECM checks the ignition timing during engine idling. If the ignition timing advances beyond the specified level within 10 seconds, the ECM interprets this as a malfunction. The MIL is illuminated and a DTC is stored when the malfunction is detected in consecutive driving cycles (2 trip detection logic).

NOTICE:
The idle speed control learned values are cleared by performing a learned value reset. Idle speed control learning needs to be performed before this DTC can be stored.

HINT:
Idle speed control learning is performed when the engine is warmed up and has been idling for 5 minutes (Click here).


A235493E04


DTC No.
DTC Detection Condition
Trouble Area
P050B
Insufficient ignition timing retard at cold start (2 trip detection logic).
  1. Throttle with motor body assembly
  2. Mass air flow meter sub-assembly
  3. PCV system
  4. Air cleaner filter element sub-assembly
  5. Intake system
  6. VVT system
  7. Wire harness or connector
  8. ECM

MONITOR STRATEGY


Related DTCs
P050B: Cold start ignition timing performance
Required Sensors/Components (Main)
Throttle with motor body assembly
Required Sensors/Components (Related)
Engine coolant temperature sensor
Mass air flow meter sub-assembly
Frequency of Operation
Once per driving cycle
Duration
10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever the following DTCs are not stored
P0010, P0020 (Camshaft timing oil control valve bank 1, 2)
P0011, P0021 (VVT system bank 1, 2 - advance)
P0012, P0022 (VVT system bank 1, 2 - retard)
P0013, P0023 (Exhaust camshaft timing oil control valve bank 1, 2)
P0014, P0024 (Exhaust VVT system bank 1, 2 - advance)
P0015, P0025 (Exhaust VVT system bank 1, 2 - retard)
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0500 (Vehicle speed sensor)
P0705 (Shift lever position switch)
P219A, P219B (Air-fuel ratio imbalance)
Battery voltage
8 V or higher
Time after engine start
3 seconds or more
Starter
Off
Engine coolant temperature at engine start
-10°C (14°F) or more
Engine coolant temperature
-10°C (14°F) or higher, and less than 50°C (122°F)
Engine idling time
3 seconds or more
Fuel-cut
Off
Vehicle speed
Less than 3 km/h (1.875 mph)
Atmospheric pressure
76 kPa(abs) [570 mmHg(abs)] or higher

TYPICAL MALFUNCTION THRESHOLDS


Accumulated time when ignition timing retard is cut off
5 seconds or more

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the engine switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the Techstream on [A].
  6. Enter the following menus: Powertrain / Engine / Data List / Primary / Coolant Temp.
  7. Check that "Coolant Temp" in the Data List is within the range of -10 to 50°C (14 to 122°F).
  8. Start the engine and warm it up until the coolant temperature is the same as the coolant temperature in the freeze frame data.
  9. Idle the engine for 1 minute or more [B].
  10. Enter the following menus: Powertrain / Engine / Trouble Codes [C].
  11. Read the pending DTC.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  13. Input the DTC: P050B.
  14. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, idle the engine for 3 minutes, let the engine cool down, and then perform steps [A] through [C] again.

  15. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0102 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. DTC P050B may be set when the engine has the symptoms listed below. If necessary, check the trouble areas listed below.

    Symptoms
    Factor
    Trouble Area
    Low idle speed when engine is cold
    (immediately after engine start)
    Excessive engine friction
    1. Engine oil deterioration
    2. Drive belt tension
    3. A/C compressor
    4. Generator
    Rough idle when engine is cold
    (immediately after engine start)
    Abnormal combustion
    Fuel quality
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050B)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P050B is output
    A
    DTC P050B and other DTCs are output
    B

    HINT:
    If any DTCs other than P050B are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (FUEL TRIM)

HINT:
Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter sub-assembly.

  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Data List / Gas AF Control / Short FT #1, Long FT #1, Short FT #2 and Long FT #2.

  1. Read the values displayed on the Techstream at engine idle.

  1. Add together the Short FT #1 and Long FT #1 values, and the Short FT #2 and Long FT #2 values to obtain the total fuel trim.

    Standard:
    The total of the Short FT #1 and Long FT #1 values, and the total of the Short FT #2 and Long FT #2 values is between -20% and 20%.



NG
Go to step 5
OK


3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)
  1. Inspect that there are no deposits around the throttle valve and throttle valve condition.

    OK:
    No deposits around the throttle valve and throttle valve moves smoothly.


    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 15
A


4.REPAIR OR REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Repair or replace the throttle with motor body assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the throttle with motor body assembly (Click here).



NEXT
Go to step 14

5.CHECK PCV SYSTEM
  1. Check the PCV hose connections (Click here).

    OK:
    PCV valve and hose are connected correctly and are not damaged.



NG
Go to step 10
OK


6.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks from intake system.



NG
Go to step 11
OK


7.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Visually check that the air cleaner filter element sub-assembly is not excessively contaminated with dirt or oil.

    OK:
    The air cleaner filter element sub-assembly is not excessively contaminated with dirt or oil.



NG
Go to step 12
OK


8.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VVT LINEAR)
  1. Operate the VVT system through the Active test, and check if the VVT system is operating normally.

    1. Perform the Active Test, referring to DTC P0011 inspection procedure (VVT system for intake camshaft) .

    2. Perform the Active Test, referring to DTC P0014 inspection procedure (VVT system for exhaust camshaft) .



NG
Go to step 13
OK


9.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Data List / Primary / MAF, Coolant Temp and Engine Speed.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 2500 rpm.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    MAF
    Shift lever position: N
    A/C: Off
    Engine Speed: 2500 rpm
    Between 8 gm/sec and 19 gm/sec



OK
Go to step 15

NG
Go to step 16

10.REPAIR OR REPLACE PCV HOSE
  1. Repair or replace the PCV valve or hose.



NEXT
Go to step 14

11.REPAIR OR REPLACE INTAKE SYSTEM
  1. Repair or replace the intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NEXT
Go to step 14

12.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Replace the air cleaner filter element sub-assembly.



NEXT
Go to step 14

13.CHECK AND REPAIR VVT SENSOR
  1. Check and repair the VVT system.

    HINT:
    1. Refer to DTC P0011 Inspection Procedure (VVT system for intake camshaft) .
    2. Refer to DTC P0014 Inspection Procedure (VVT system for exhaust camshaft) .


NEXT


14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)

NOTICE:
In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG) and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Data List / Primary / Coolant Temp.

  1. Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F)

  1. Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  1. Input the DTC: P050B.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P050B is output)
    B



B
Go to step 16
A

END 

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)

NOTICE:
In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG) and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Data List / Primary / Coolant Temp.

  1. Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F)

  1. Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  1. Input the DTC: P050B.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P050B is output)
    B



B
Go to step 16
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

16.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


17.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)

NOTICE:
In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG) and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Data List / Primary / Coolant Temp.

  1. Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F)

  1. Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  1. Input the DTC: P050B.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    ABNORMAL (DTC P050B is output)
    A
    NORMAL (DTC is not output)
    B



B
END
A


18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E14-5 (VG) - E26-98 (VG)
    Always
    Below 1 Ω
    E14-4 (E2G) - E26-130 (E2G)
    Always
    Below 1 Ω
    E14-5 (VG) or E26-98 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


19.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
  1. Replace the mass air flow meter sub-assembly (Click here).

    HINT:
    1. If the result of the inspection performed in step 9 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.
    2. Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (Click here).


NEXT


20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NOTICE:
In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG) and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Data List / Primary / Coolant Temp.

  1. Check that the engine coolant temperature is between -10 and 50°C (14 and 122°F).

  1. Start the engine and warm it up until the engine coolant temperature is the same as the engine coolant temperature in the freeze frame data.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  1. Input the DTC: P050B.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P050B is output)
    B



B
REPLACE ECM (Click here)
A

END