Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER

FRONT BUMPER > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT BUMPER SIDE RETAINER LH


    B279848
  1. Engage the claw.

  1. Install the front bumper side retainer LH with the bolt.

    Torque:
    4.1 N*m{ 42 kgf*cm , 36 in.*lbf }



2. INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:
Use the same procedure as for the LH side.



3. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    B279849
  1. Install the front bumper reinforcement sub-assembly with the 6 bolts.

    Torque:
    61 N*m{ 622 kgf*cm , 45 ft.*lbf }

  1. Engage the 5 clamps.



4. INSTALL FRONT BUMPER ENERGY ABSORBER


    B279850
  1. Engage the 2 guides to install the front bumper energy absorber.



5. INSTALL NO. 1 LOWER RADIATOR GRILLE


  1. for Standard:



      B279845
    1. Engage the 2 guides and 16 claws to install the No. 1 lower radiator grille.



  1. for Sport Package:



      B280503
    1. Engage the 2 guides and 6 claws to install the No. 1 lower radiator grille.



6. INSTALL FRONT BUMPER HOLE COVER LH (for Standard)


  1. w/ Fog Light:



      B281522
    1. Engage the 2 claws and 2 guides to install the fog light mounting bracket LH.



    B279847
  1. Engage the 5 claws to install the front bumper hole cover LH.



7. INSTALL FRONT BUMPER HOLE COVER RH (for Standard)

HINT:
Use the same procedure as for the LH side.



8. INSTALL FRONT BUMPER HOLE COVER LH (for Sport Package)


    B280505
  1. Engage the 3 claws and guide to install the fog light mounting bracket LH.



    B280504
  1. Engage the 2 claws to install the front bumper side moulding LH.

  1. Install the 2 screws.



    B280502
  1. Engage the 7 claws to install the front bumper hole cover LH.

  1. Install the 2 screws.



9. INSTALL FRONT BUMPER HOLE COVER RH (for Sport Package)

HINT:
Use the same procedure as for the LH side.



10. INSTALL FRONT FENDER LINER RETAINER


    B279846
  1. Engage the claw to install the front fender liner retainer.

    HINT:
    Use the same procedure for the RH side and LH side.



11. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (for Standard)


  1. w/o Side Turn Signal Light:



      B281520E01
    1. Engage the 2 hooks.
      Text in Illustration 
      *1
      Hook

    2. Install the front bumper extension mounting bracket with the 2 screws.



  1. w/ Side Turn Signal Light:



      B295694
    1. Engage the 2 hooks.
      Text in Illustration 
      *1
      Hook

    2. Install the front bumper extension mounting bracket with the 2 screws.



12. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (for Sport Package)


    B281521E01
  1. Engage the 2 hooks.
    Text in Illustration 
    *1
    Hook

  1. Install the front bumper extension mounting bracket with the 2 screws.



13. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)
  1. Engage the 2 guides.

  1. Install the fog light assembly with the screw.

    Torque:
    1.6 N*m{ 16 kgf*cm , 14 in.*lbf }



14. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure as for the LH side.



15. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)


    E232468E01
  1. Engage the 2 claws to install the No. 1 ultrasonic sensor retainer to the front bumper assembly.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side
    *a
    Keyhole
    *b
    Snap

    NOTICE:
    1. Do not damage the front bumper with the protrusion when installing the retainer.
    2. Securely install the No. 1 ultrasonic sensor retainer so that there are no gaps between the retainer and surface of the front bumper.

    HINT:
    When installing the retainer, align the keyhole and snap as shown in the illustration.



16. INSTALL NO. 1 ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)


    E228019E01
  1. Engage the 2 claws to install the No. 1 ultrasonic sensor to the No. 1 ultrasonic sensor retainer.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

    NOTICE:
    Push the No. 1 ultrasonic sensor retainer from the outside of the bumper when there is a gap between the retainer and the bumper surface. In this case, do not push on the ultrasonic sensor.