Home › Engine / Hybrid System ยท 2AR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REMOVAL

for Preparation Click here



1. REMOVE ENGINE HANGERS


    A264710E01
  1. Remove the 2 bolts and 2 engine hangers.
    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No .2 Engine Hanger



2. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    A195867
  1. Remove the engine oil level dipstick.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



3. REMOVE MANIFOLD STAY


    A195975
  1. Remove the bolt, nut and manifold stay.



4. REMOVE NO. 2 MANIFOLD STAY


    A209598
  1. Remove the bolt, nut and No. 2 manifold stay.



5. REMOVE EGR INLET EXHAUST MANIFOLD PLATE (for PZEV)


    A254733
  1. Remove the bolt and EGR inlet exhaust manifold plate.



6. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (except PZEV)


    A209579
  1. Remove the 4 bolts and No. 1 exhaust manifold heat insulator.



7. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY


    A195979
  1. Remove the 5 nuts and exhaust manifold converter sub-assembly (except PZEV).



    A254734
  1. Remove the 5 nuts and exhaust manifold converter sub-assembly (for PZEV).



    A195981E01
  1. Remove the exhaust manifold to head gasket (except PZEV).



    A254735E01
  1. Remove the exhaust manifold to head gasket (for PZEV).



8. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET


    A210230
  1. Remove the 4 bolts and bracket.



9. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY


    A254781
  1. Disconnect the fuel tube from the clamp.

  1. Disconnect the throttle body connector.



    A254780
  1. Disconnect the water by-pass hose from the throttle with motor body assembly.

  1. Disconnect the No. 2 water by-pass hose from the throttle with motor body assembly.



    A195069
  1. Remove the 4 bolts and throttle with motor body assembly with fuel tube bracket.



    A195070
  1. Remove the bolt and fuel tube bracket.



    A195071
  1. Remove the gasket from the intake manifold.



10. REMOVE WATER BY-PASS HOSE


    A196855
  1. Remove the No. 1 and No. 2 water by-pass hoses.



11. REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)


    A254745
  1. Disconnect the union to connector tube hose and wire harness clamp.

  1. Disconnect the 2 vacuum hoses and connector.

  1. Remove the bolt and vacuum switching valve assembly.



12. DISCONNECT NO. 2 VENTILATION HOSE


    A196046
  1. Disconnect the No. 2 ventilation hose from the intake manifold.



13. REMOVE UNION TO CONNECTOR TUBE HOSE


    A196048
  1. Disconnect the union to connector tube hose from the intake manifold.



14. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    A252631
  1. Remove the 2 bolts, and then remove the fuel delivery pipe together with the 4 fuel injectors.

    NOTICE:
    Be careful not to drop the fuel injectors when removing the fuel delivery pipe.



    A211217
  1. Remove the 2 fuel delivery spacers from the cylinder head.

  1. Remove the 4 injector vibration insulators from the cylinder head.



15. REMOVE INTAKE MANIFOLD


    A205609
  1. Remove the 2 bolts and 2 wire harness clamp brackets.



    A254751
  1. Disconnect the fuel vapor feed hose.

  1. Disconnect the 3 wire harness clamps and connector.

  1. Remove the bolt and wire harness clamp bracket.



    A199910
  1. Apply battery voltage to the terminals of the connector to close the tumble control valves.

    Standard:
    Tester Connection
    Specified Condition
    Positive (+) battery voltage applied to terminal 8 (M-), and negative (-) battery voltage applied to terminal 4 (M+)
    Open → Closed

    NOTICE:
    1. If this procedure is not performed, the tumble control valves may be damaged when the intake manifold is removed.
    2. Apply battery voltage for 1 to 3 seconds.
    3. If battery voltage is applied for more than 3 seconds, the actuator may be damaged.
    4. Do not allow the lead wires to contact the other terminals.



    A256256
  1. Remove the bolt and separate the wire harness.

  1. Disconnect the 2 wire harness clamps and intake air control valve actuator connector.



    A254722
  1. Remove the 6 bolts and intake manifold.

    NOTICE:
    The tumble control valves may be damaged if they are not closed before removing the intake manifold.

    HINT:
    Connect the battery to the terminals of the actuator to operate the motor and close the valves .



    A207714
  1. Remove the intake manifold gasket from the intake manifold.



    A196049
  1. Disconnect the 2 vacuum hoses from the intake manifold and remove the No. 1 check valve.



    A196050
  1. Remove the bolt and wire harness clamp bracket.



16. REMOVE SENSOR WIRE


    A256483
  1. Disconnect the knock control sensor connector.

  1. Remove the bolt and knock control sensor wire.



17. REMOVE KNOCK CONTROL SENSOR


    A212472
  1. Disconnect the sensor connector.

  1. Remove the bolt and knock control sensor.



18. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY


    A194913
  1. Disconnect the connector.

  1. Using a 24 mm deep socket wrench, remove the oil pressure switch.



19. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


    A254801
  1. Disconnect the engine coolant temperature sensor connector.



    A254800
  1. Remove the 2 bolts and disconnect the wire harness.



    A255139E01
  1. Using a 19 mm ball joint lock nut wrench, remove the engine coolant temperature sensor.
    Text in Illustration 
    *1
    Ball Joint Lock Nut Wrench
    *2
    Gasket

  1. Remove the gasket from the engine coolant temperature sensor.



20. REMOVE IGNITION COIL ASSEMBLY
  1. Disconnect the 4 ignition coil assembly connectors.



    A207955
  1. Remove the 4 bolts and 4 ignition coil assemblies.