ENGINE UNIT > DISASSEMBLY |
| 1. REMOVE ENGINE COVER JOINT |
![]() |
Remove the 3 joints.
| 2. REMOVE SPARK PLUG |
![]() |
Using a spark plug wrench, remove the 4 spark plugs.
| 3. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
Camshaft timing oil control valve assembly (for exhaust side)
![]() |
Disconnect the oil control valve connector.
Remove the bolt and oil control valve.
![]() |
Remove the O-ring from the oil control valve.
| *1 | O-ring |
Camshaft timing oil control valve assembly (for intake side)
![]() |
Disconnect the oil control valve connector.
Remove the bolt and oil control valve.
![]() |
Remove the O-ring from the oil control valve.
| *1 | O-ring |
| 4. REMOVE CAMSHAFT POSITION SENSOR |
Camshaft position sensor (for Exhaust Side)
![]() |
Disconnect the sensor connector.
Remove the bolt and sensor.
Camshaft position sensor (for Intake Side)
![]() |
Disconnect the sensor connector.
Remove the bolt and sensor.
| 5. REMOVE OIL FILLER CAP SUB-ASSEMBLY |
Remove the oil filler cap from the cylinder head.
Remove the gasket from the oil filler cap.
| 6. REMOVE CRANKSHAFT POSITION SENSOR |
![]() |
Disconnect the sensor connector.
Remove the bolt and sensor.
| 7. REMOVE VENTILATION VALVE SUB-ASSEMBLY |
![]() |
Disconnect the No. 2 ventilation hose from the ventilation valve sub-assembly.
![]() |
Using a 19 mm deep socket wrench, remove the ventilation valve sub-assembly.
| *1 | 19 mm Deep Socket Wrench |
| 8. REMOVE VENTILATION CASE SUB-ASSEMBLY |
![]() |
Remove the 8 bolts and 2 nuts.
![]() |
Remove the ventilation case by prying between the ventilation case and cylinder block with a screwdriver.
| 9. REMOVE SEPARATOR CASE |
![]() |
Remove the 2 bolts, separator case and gasket.
| 10. REMOVE NO. 1 WATER BY-PASS PIPE |
![]() |
Remove the bolt, 2 nuts, water by-pass pipe and gasket.
| 11. REMOVE WATER INLET |
![]() |
Remove the 2 nuts and water inlet.
| 12. REMOVE THERMOSTAT |
Remove the thermostat.
Remove the gasket from the thermostat.
| 13. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the bolt and V-ribbed belt tensioner.
| 14. REMOVE ENGINE WATER PUMP ASSEMBLY |
![]() |
Remove the 7 bolts, engine water pump and gasket.
| 15. REMOVE WATER INLET HOUSING |
![]() |
Remove the 4 bolts, nut, inlet water housing and gasket.
| 16. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, hold the crankshaft pulley and loosen the pulley bolt. Further loosen the bolt until 2 or 3 threads are screwed into the crankshaft.
| *a | Hold |
| *b | Turn |
![]() |
Using SST and the pulley bolt, remove the crankshaft pulley.
| *1 | Pulley Bolt |
| *a | Hold |
| *b | Turn |
| 17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the 16 bolts, 3 seal washers, cylinder head cover and gasket.
![]() |
Remove the 3 gaskets from the camshaft bearing caps.
| 18. REMOVE SPARK PLUG TUBE GASKET |
![]() |
Using a screwdriver, pry out the 4 plug tube gaskets.
| 19. REMOVE ENGINE MOUNTING BRACKET RH |
![]() |
Remove the 5 bolts and engine mounting bracket RH.
| 20. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Remove the 17 bolts and 2 nuts.
![]() |
Remove the timing chain cover by prying between the timing chain cover and cylinder head, camshaft housing, cylinder block and stiffening crankcase with a screwdriver as shown in the illustration.
![]() |
Remove the 3 gaskets from the stiffening crankcase.
| 21. REMOVE TIMING CHAIN COVER TIGHT PLUG |
![]() |
Using a 14 mm hexagon wrench, remove the plug and gasket.
| 22. REMOVE TIMING CHAIN COVER PLATE |
![]() |
Remove the 4 bolts, timing chain cover plate and gasket.
| 23. REMOVE TIMING CHAIN COVER OIL SEAL |
![]() |
Using a screwdriver and wooden block, pry out the oil seal.
| *1 | Wooden Block |
| 24. SET NO. 1 CYLINDER TO TDC/COMPRESSION |
Temporarily install the crankshaft pulley bolt.

| *a | Approximately 7° | *b | Approximately 32° |
| *c | Timing Mark | *d | Key |
Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.
Remove the crankshaft pulley bolt.
| 25. REMOVE TIMING CHAIN GUIDE |
![]() |
Remove the bolt and timing chain guide.
| 26. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Allow the plunger to extend slightly, and then rotate the stopper plate counterclockwise to release the lock. Once the lock is released, push the plunger into the tensioner.
| *1 | Stopper Plate |
| *2 | Plunger |
![]() |
Move the stopper plate clockwise to set the lock, and insert a pin into the stopper plate hole.
| *1 | Pin |
![]() |
Remove the 2 bolts, chain tensioner and gasket.
| 27. REMOVE CHAIN TENSIONER SLIPPER |
![]() |
Remove the bolt and chain tensioner slipper.
| 28. REMOVE CHAIN SUB-ASSEMBLY |
Remove the chain sub-assembly.
| 29. REMOVE NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Remove the 2 bolts and chain vibration damper.
| 30. REMOVE CRANKSHAFT TIMING SPROCKET |
![]() |
Remove the crankshaft timing sprocket from the crankshaft.
| 31. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Hold the hexagonal portion of the camshaft with a wrench and remove the bolt and camshaft timing gear assembly.
| *a | Hold |
| *b | Turn |
| 32. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
![]() |
Hold the hexagonal portion of the camshaft with a wrench and remove the bolt and camshaft timing exhaust gear assembly.
| *a | Hold |
| *b | Turn |
| 33. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY |
![]() |
Uniformly loosen and remove the 20 bearing cap bolts in the sequence shown in the illustration.
![]() |
Remove the camshaft housing by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver.
| 34. REMOVE CAMSHAFT BEARING CAP |
![]() |
Remove the 11 bearing cap bolts in the sequence shown in the illustration.
Remove the 5 bearing caps.
| 35. REMOVE OIL CONTROL VALVE FILTER |
![]() |
Remove the oil control valve filter from the No. 1 camshaft bearing cap.
| 36. REMOVE CAMSHAFT |
Remove the camshaft and No. 2 camshaft.
| 37. REMOVE NO. 1 CAMSHAFT BEARING |
![]() |
Remove the No. 1 camshaft bearing.
| 38. REMOVE NO. 2 CAMSHAFT BEARING |
![]() |
Remove the No. 2 camshaft bearing.
| 39. REMOVE CAMSHAFT HOUSING STUD BOLT |
| 40. REMOVE CAMSHAFT BEARING CAP SETTING RING PIN |
| 41. REMOVE CAMSHAFT HOUSING STRAIGHT PIN |
| 42. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
Remove the 16 valve rocker arms from the cylinder head sub-assembly.
| 43. REMOVE VALVE LASH ADJUSTER ASSEMBLY |
Remove the 16 valve lash adjusters from the cylinder head sub-assembly.
| 44. REMOVE VALVE STEM CAP |
Remove the 16 valve stem caps from the cylinder head sub-assembly.
| 45. REMOVE CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.
Remove the cylinder head sub-assembly.
| 46. REMOVE CYLINDER HEAD GASKET |
Remove the cylinder head gasket from the cylinder block.
| 47. REMOVE CYLINDER BLOCK WATER JACKET SPACER |
![]() |
Remove the cylinder block water jacket spacer from the cylinder block.
| 48. REMOVE OIL FILTER CAP ASSEMBLY |
![]() |
Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
| *1 | Pipe |
| *2 | Hose |
![]() |
Remove the oil filter drain plug from the oil filter cap.
![]() |
Install the pipe to the oil filter cap.
| *1 | Valve |
| *2 | Cap |
| *3 | O-ring |
| *4 | Pipe |
![]() |
Check that the oil is drained from the oil filter. Then disconnect the pipe as shown in the illustration and remove the O-ring.
![]() |
Using SST, remove the oil filter cap.
| *1 | Oil Filter Bracket Clip |
![]() |
Remove the oil filter element and O-ring from the oil filter cap.
| *1 | Oil Filter Element |
| *2 | Oil Filter Cap |
| *3 | O-ring |
| 49. REMOVE OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 11 bolts and 2 nuts.
| *1 | Nut |
![]() |
Insert the blade of an oil pan seal cutter between the oil pan and stiffening crankcase, cut off the applied sealer and remove the oil pan.
| 50. REMOVE OIL STRAINER SUB-ASSEMBLY |
![]() |
Remove the 3 bolts, oil strainer and gasket.
| 51. REMOVE NO. 1 OIL PAN BAFFLE PLATE |
![]() |
Remove the 5 bolts and oil pan baffle plate.
| 52. INSPECT CRANKSHAFT BACKLASH |
![]() |
Using a dial indicator, measure the backlash of the crankshaft and balance shaft as shown in the illustration.
| 53. REMOVE ENGINE BALANCER ASSEMBLY |
![]() |
Remove the 7 bolts and engine balancer.
| 54. INSPECT BALANCE SHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the No. 1 balance shaft back and forth.
| 55. REMOVE STIFFENING CRANKCASE ASSEMBLY |
![]() |
Remove the 7 bolts.
![]() |
Using a screwdriver, remove the stiffening crankcase by prying between the stiffening crankcase and cylinder block at the places shown in the illustration.
| *a | LH Side: |
| *b | RH Side: |
| 56. REMOVE STIFFENING CRANKCASE STUD BOLT |
| 57. REMOVE STIFFENING CRANKCASE RING PIN |
| 58. REMOVE REAR ENGINE OIL SEAL |
![]() |
Remove the rear engine oil seal from the cylinder block.