Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY

CENTER AIRBAG SENSOR ASSEMBLY > REMOVAL

for Preparation Click here



1. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY
(Click here)


2. REMOVE REAR CONSOLE BOX ASSEMBLY
(Click here)


3. REMOVE FRONT DOOR SCUFF PLATE LH


    B278977
  1. Disengage the 10 claws and remove the front door scuff plate LH.



4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B278978
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.



5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Disconnect the front door opening trim weatherstrip LH to the extent that allows the removal of the instrument side panel LH.



6. REMOVE INSTRUMENT SIDE PANEL LH


    B278008
  1. Using a moulding remover, disengage the 4 claws as shown in the illustration.



    B278010
  1. Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.



7. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B279865
  1. Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.



8. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    B279867
  1. Remove the bolt <B> and screw <C> or <D>.



    B279868
  1. Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.



9. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B280314
  1. Remove the 2 screws <C> or <D>.

  1. Open the lower instrument panel door.



    B280315
  1. Remove the 3 screws <C> or <D>.



    B280312
  1. Disengage the 2 clips and guide.



    B284908
  1. Disengage the glove compartment light as shown in the illustration.

  1. Disconnect each connector and remove the lower instrument panel sub-assembly.



10. REMOVE BOX BOTTOM MAT


    B279879
  1. Remove the box bottom mat.



11. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B279880
  1. Remove the 2 screws <C> or <D>.



    B279881
  1. Disengage the 4 clips and guide as shown in the illustration.

  1. Disconnect each connector to remove the upper console panel sub-assembly.



12. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    B280290
  1. Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.



    B280291
  1. Remove the 2 screws <C> or <D>.



    B280292
  1. Disengage the clip and 3 guides to remove the front No. 2 console box insert as shown in the illustration.



13. REMOVE CONSOLE BOX INSERT


    B279900
  1. Remove the 2 screws <C> or <D>.



    B279901
  1. Disengage the clip and 3 guides to remove the console box insert as shown in the illustration.



14. REMOVE FLOOR CARPET BRACKET LH


    E227160
  1. Remove the 2 clips.

  1. Disengage the 2 guides to remove the floor carpet bracket LH.



15. REMOVE FLOOR CARPET BRACKET RH


    E227159
  1. Remove the 2 clips.

  1. Disengage the 2 guides to remove the floor carpet bracket RH.



16. REMOVE NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)


    E227163
  1. Remove the clip and the No. 1 console box duct.



17. REMOVE AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Turn back the carpet.



    B278814
  1. Disconnect the connectors from the airbag sensor assembly as shown in the illustration.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  1. Remove the 3 bolts and airbag sensor assembly.