Home › Audio/Visual/Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type)

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Harness or connector
  2. Speaker
  3. DCM (Telematics transceiver)*1
  4. Stereo component amplifier assembly*2
  5. Radio and display receiver assembly*3
  1. *1: w/ Manual (SOS) Switch
  2. *2: for 10 Speakers
  3. *3: for 6 Speakers

WIRING DIAGRAM


for 6 Speakers

E226481E10


for 10 Speakers

E226482E05


E226483E06


INSPECTION PROCEDURE

NOTICE:
After replacing the radio and display receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).

1.CONFIRM MODEL

Result:
Result
Proceed to
for 6 Speakers
A
for 10 Speakers
B



B
Go to step 7
A


2.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the radio and display receiver assembly and speakers.

  1. Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I152-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    I152-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    I152-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    I152-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    I153-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    I153-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    I153-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    I153-6 (RL-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I83-3 (+) - Body ground
    Always
    10 kΩ or higher
    I83-1 (-) - Body ground
    Always
    10 kΩ or higher
    I1-3 (+) - Body ground
    Always
    10 kΩ or higher
    I1-1 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


  1. Resistance check



      E219303E36
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J5-1 - J5-2
      Always
      3.2 to 4.8 Ω
      K5-1 - K5-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


  1. Resistance check



      E226097E13
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I83-2 (TWR-) - I83-4 (TWR+)
      Always
      10 kΩ or higher
      I83-1 (-) - I83-2 (TWR-)
      Always
      Below 1 Ω
      I83-3 (+) - I83-4 (TWR+)
      Always
      Below 1 Ω
      I1-2 (TWL-) - I1-4 (TWL+)
      Always
      10 kΩ or higher
      I1-1 (-) - I1-2 (TWL-)
      Always
      Below 1 Ω
      I1-3 (+) - I1-4 (TWL+)
      Always
      Below 1 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


5.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
  1. Check that the malfunction disappears when a known good speaker is installed (Click here).

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 6
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE) 

6.INSPECT REAR SPEAKER ASSEMBLY


  1. Resistance check



      E219303E37
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O18-1 - O18-2
      Always
      3.2 to 4.8 Ω
      O21-1 - O21-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)  

7.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the stereo component amplifier assembly, DCM (telematics transceiver)*1 and speakers.

    1. *1: w/ Manual (SOS) Switch

  1. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-15 (FR+) - Body ground
    Always
    10 kΩ or higher
    I68-30 (FR-) - Body ground
    Always
    10 kΩ or higher
    I68-11 (FL+) - Body ground
    Always
    10 kΩ or higher
    I68-26 (FL-) - Body ground
    Always
    10 kΩ or higher
    I68-12 (TWR+) - Body ground
    Always
    10 kΩ or higher
    I68-27 (TWR-) - Body ground
    Always
    10 kΩ or higher
    I68-14 (TWL+) - Body ground
    Always
    10 kΩ or higher
    I68-29 (TWL-) - Body ground
    Always
    10 kΩ or higher
    I68-13 (CTR+) - Body ground
    Always
    10 kΩ or higher
    I68-28 (CTR-) - Body ground
    Always
    10 kΩ or higher
    I68-10 (SR+) - Body ground
    Always
    10 kΩ or higher
    I68-25 (SR-) - Body ground
    Always
    10 kΩ or higher
    I68-9 (SL+) - Body ground
    Always
    10 kΩ or higher
    I68-24 (SL-) - Body ground
    Always
    10 kΩ or higher
    I68-8 (WF1+) - Body ground
    Always
    10 kΩ or higher
    I68-23 (WF1-) - Body ground
    Always
    10 kΩ or higher

  1. w/ Manual (SOS) Switch
    Measure the resistance between the DCM (telematics transceiver) and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I135-5 (SPO+) - Body ground
    Always
    10 kΩ or higher
    I135-6 (SPO-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E219303E38
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J5-1 (+) - J5-2 (-)
      Always
      4.6 to 6.6 Ω
      K5-1 (+) - K5-2 (-)
      Always
      4.6 to 6.6 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


9.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E219304E20
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I84-4 - I84-3
      Always
      3.4 to 5.2 Ω
      I2-4 - I2-3
      Always
      3.4 to 5.2 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


10.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    E222247E16
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I60-2 - I60-1
      Always
      6.8 to 10.2 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front No. 3 Speaker Assembly)



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


11.INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    E222247E17
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O19-2 - O19-1
      Always
      6.8 to 10.2 Ω
      O20-2 - O20-1
      Always
      6.8 to 10.2 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear No. 2 Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


12.INSPECT REAR SPEAKER ASSEMBLY


    E219303E39
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O22-1 - O22-2
      Always
      4.8 to 6.8 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Rear Speaker Assembly)

  1. Proceed to the next step based on the inspection result.

    Result:
    Condition
    Proceed to
    OK (w/ Manual (SOS) Switch)
    A
    OK (w/o Manual (SOS) Switch)
    B
    NG
    C



B
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

C
REPLACE REAR SPEAKER ASSEMBLY (Click here)
A


13.INSPECT DCM (TELEMATICS TRANSCEIVER)


    E169849E18
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I135-2 (SPI+) - I135-5 (SPO+)
      Always
      Below 1 Ω
      I135-3 (SPI-) - I135-6 (SPO-)
      Always
      Below 1 Ω
      I135-2 (SPI+) - I135-3 (SPI-)
      Always
      10 kΩ or higher
      I135-5 (SPO+) - I135-6 (SPO-)
      Always
      10 kΩ or higher
      I135-2 (SPI+) - Body ground
      Always
      10 kΩ or higher
      I135-3 (SPI-) - Body ground
      Always
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (DCM (Telematics Transceiver))



NG
REPLACE DCM (TELEMATICS TRANSCEIVER) (Click here)
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)