Home › Audio/Visual/Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Harness or connector
  2. Speaker
  3. DCM (telematics transceiver)*1
  4. Stereo component amplifier assembly
  1. *1: w/ Manual (SOS) Switch

WIRING DIAGRAM


E226482E02


E226483E02


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the stereo component amplifier assembly, DCM (telematics transceiver)*1 and speakers.

    1. *1: w/ Manual (SOS) Switch

  1. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-15 (FR+) - Body ground
    Always
    10 kΩ or higher
    I68-30 (FR-) - Body ground
    Always
    10 kΩ or higher
    I68-11 (FL+) - Body ground
    Always
    10 kΩ or higher
    I68-26 (FL-) - Body ground
    Always
    10 kΩ or higher
    I68-12 (TWR+) - Body ground
    Always
    10 kΩ or higher
    I68-27 (TWR-) - Body ground
    Always
    10 kΩ or higher
    I68-14 (TWL+) - Body ground
    Always
    10 kΩ or higher
    I68-29 (TWL-) - Body ground
    Always
    10 kΩ or higher
    I68-13 (CTR+) - Body ground
    Always
    10 kΩ or higher
    I68-28 (CTR-) - Body ground
    Always
    10 kΩ or higher
    I68-10 (SR+) - Body ground
    Always
    10 kΩ or higher
    I68-25 (SR-) - Body ground
    Always
    10 kΩ or higher
    I68-9 (SL+) - Body ground
    Always
    10 kΩ or higher
    I68-24 (SL-) - Body ground
    Always
    10 kΩ or higher
    I68-8 (WF1+) - Body ground
    Always
    10 kΩ or higher
    I68-23 (WF1-) - Body ground
    Always
    10 kΩ or higher

  1. w/ Manual (SOS) Switch
    Measure the resistance between the DCM (telematics transceiver) and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I135-5 (SPO+) - Body ground
    Always
    10 kΩ or higher
    I135-6 (SPO-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E219303E40
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J5-1 (+) - J5-2 (-)
      Always
      4.6 to 6.6 Ω
      K5-1 (+) - K5-2 (-)
      Always
      4.6 to 6.6 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E219304E15
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I84-4 - I84-3
      Always
      3.4 to 5.2 Ω
      I2-4 - I2-3
      Always
      3.4 to 5.2 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    E222247E10
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I60-1 - I60-2
      Always
      6.8 to 10.2 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front No. 3 Speaker Assembly)



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


5.INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    E222247E11
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O19-1 - O19-2
      Always
      6.8 to 10.2 Ω
      O20-1 - O20-2
      Always
      6.8 to 10.2 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear No. 2 Speaker Assembly)



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK


6.INSPECT REAR SPEAKER ASSEMBLY


    E219303E16
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O22-1 - O22-2
      Always
      4.8 to 6.8 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Rear Speaker Assembly)

  1. Proceed to the next step based on the inspection result.

    Result:
    Condition
    Proceed to
    OK (w/ Manual (SOS) Switch)
    A
    OK (w/o Manual (SOS) Switch)
    B
    NG
    C



B
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

C
REPLACE REAR SPEAKER ASSEMBLY (Click here)
A


7.INSPECT DCM (TELEMATICS TRANSCEIVER)


    E169849E15
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I135-2 (SPI+) - I135-5 (SPO+)
      Always
      Below 1 Ω
      I135-3 (SPI-) - I135-6 (SPO-)
      Always
      Below 1 Ω
      I135-2 (SPI+) - I135-3 (SPI-)
      Always
      10 kΩ or higher
      I135-5 (SPO+) - I135-6 (SPO-)
      Always
      10 kΩ or higher
      I135-2 (SPI+) - Body ground
      Always
      10 kΩ or higher
      I135-3 (SPI-) - Body ground
      Always
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (DCM (Telematics Transceiver))



NG
REPLACE DCM (TELEMATICS TRANSCEIVER) (Click here)
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)