Home › Audio/Visual/Telematics › CELLULAR COMMUNICATION › SAFETY CONNECT SYSTEM

DTC    B1572    Telephone Microphone Error

for Preparation Click here


DESCRIPTION

This DTC is set when the DCM (Telematics Transceiver) detects a malfunction in the telephone microphone circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1572
Current of MCVD reaches malfunction criteria for 10 seconds while engine switch is on (IG).
  1. Wire harness or connector
  2. Telephone microphone (Roof console box assembly)
  3. DCM (Telematics Transceiver)

WIRING DIAGRAM


B278893E04


INSPECTION PROCEDURE

1.CHECK DTC
  1. Turn the engine switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG) and wait for 10 seconds.

  1. Turn the Techstream on.

  1. Perform "Health Check" and check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1572 is output
    A
    DTC B1572 is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE POWER SOURCE)


    B234642E20
  1. Remove the roof console box assembly but do not disconnect the connectors (Click here).

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S12-14 (MACC) - Body ground
    Engine switch on (ACC)
    4 to 6 V

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S12-12 (MCO-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Roof Console Box Assembly)



NG
Go to step 4
OK


3.CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - ROOF CONSOLE BOX ASSEMBLY)
  1. Disconnect the I135 DCM (Telematics Transceiver) connector.

  1. Disconnect the S12 roof console box assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I135-34 (MCI+) - S12-13 (MCO+)
    Always
    Below 1 Ω
    I135-35 (MCI-) - S12-12 (MCO-)
    Always
    Below 1 Ω
    I135-34 (MCI+) - Body ground
    Always
    10 kΩ or higher
    I135-35 (MCI-) - Body ground
    Always
    10 kΩ or higher
    I135-32 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TELEPHONE MICROPHONE (ROOF CONSOLE BOX ASSEMBLY) (Click here)  

4.INSPECT DCM (TELEMATICS TRANSCEIVER) (TELEPHONE MICROPHONE POWER SOURCE)


    B235166E76
  1. Remove the DCM (Telematics Transceiver) but do not disconnect the connectors (Click here).

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I135-33 (MCVD) - Body ground
    Engine switch on (ACC)
    4 to 6 V

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    I135-35 (MCI-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (DCM (Telematics Transceiver))



NG
Go to step 5
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

5.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The engine switch must be off.
    2. Do not swap the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)