DTC B1570 Manual (SOS) Switch Red Indicator Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1570 | Current for manual (SOS) switch red indicator reaches malfunction criteria for 10 seconds when engine switch is on (IG). |
|

| 1.CHECK DTC |
Turn the engine switch off.
Connect the Techstream to the DLC3.
Turn the engine switch on (IG) and wait for 10 seconds.
Turn the Techstream on.
Perform "Health Check" and check for current DTCs (Click here).
| Result | Proceed to |
| DTC B1570, B1571 and B15C5 are output | A |
| DTC B1570 is output (DTC B1571 and B15C5 are not output) | B |
|
| ||||
| A | |
| 2.INSPECT ROOF CONSOLE BOX ASSEMBLY (RED INDICATOR) |
![]() |
Disconnect the S12 roof console box assembly connector.
Connect 2 dry-cell batteries (1.5 V each) in series.
Connect the positive (+) lead to terminal S12-19 (IND1) and the negative (-) lead to terminal S12-16 (GND3) of the roof console box assembly connectors.
Check if the illumination for the manual (SOS) switch red indicator comes on.
| *a | Component without harness connected (Roof Console Box Assembly) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - ROOF CONSOLE BOX ASSEMBLY) |
Disconnect the I135 DCM (Telematics Transceiver) connector.
Disconnect the S12 roof console box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I135-26 (SIG-) - S12-16 (GND3) | Always | Below 1 Ω |
| I135-26 (SIG-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.REPLACE DCM (TELEMATICS TRANSCEIVER) |
Replace the DCM (Telematics Transceiver) (Click here).
| NEXT | ||
| ||
| 5.INSPECT ROOF CONSOLE BOX ASSEMBLY (MANUAL (SOS) SWITCH RED INDICATOR CONDITION) |
Confirm the red indicator status after the engine switch is turned on (IG) (Click here).
| Result | Proceed to |
| Red indicator remains off. | A |
| Red indicator remains on. | B |
|
| ||||
| A | |
| 6.INSPECT ROOF CONSOLE BOX ASSEMBLY (RED INDICATOR INPUT VOLTAGE) |
![]() |
Remove the roof console box assembly but do not disconnect the connectors (Click here).
Connect the positive lead of a voltmeter to terminal S12-19 (IND1), and the negative lead to terminal S12-16 (GND3).
Measure the voltage.
| *a | Component with harness connected (Roof Console Box Assembly) |
|
| ||||
| OK | ||
| ||
| 7.INSPECT DCM (TELEMATICS TRANSCEIVER) (RED INDICATOR OUTPUT VOLTAGE) |
![]() |
Remove the DCM (Telematics Transceiver) but do not disconnect the connectors (Click here).
Connect the positive lead of a voltmeter to terminal I135-11 (IND1), and the negative lead to body ground.
Measure the voltage.
| *a | Component with harness connected (DCM (Telematics Transceiver)) |
|
| ||||
| OK | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - BODY GROUND) |
![]() |
Remove the DCM (Telematics Transceiver) but do not disconnect the connectors (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I135-11 (IND1) - Body ground | Always | 10 kΩ or higher |
| *a | Component with harness connected (DCM (Telematics Transceiver)) |
|
| ||||
| OK | |
| 9.REPLACE DCM (TELEMATICS TRANSCEIVER) |
Replace the DCM (Telematics Transceiver) (Click here).
| NEXT | ||
| ||