Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)

AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Speaker Circuit

for Preparation Click here


DESCRIPTION

The sound signals amplified by the radio receiver assembly are sent to the speakers from the radio receiver assembly via the speaker circuit.
If there is a short in a speaker circuit, the radio receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly or speakers.
If a short is detected in a speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM


E177570E12


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the radio receiver assembly and speakers.

  1. Measure the resistance between each of the front No. 2 speaker assemblies and the radio receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I148-1 (FR+) - I83-4 (TWR+)
    Always
    Below 1 Ω
    I148-5 (FR-) - I83-2 (TWR-)
    Always
    Below 1 Ω
    I148-2 (FL+) - I1-4 (TWL+)
    Always
    Below 1 Ω
    I148-6 (FL-) - I1-2 (TWL-)
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I1-3 (+) - K5-1
    Always
    Below 1 Ω
    I1-1 (-) - K5-2
    Always
    Below 1 Ω
    I83-3 (+) - J5-1
    Always
    Below 1 Ω
    I83-1 (-) - J5-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear speaker assemblies and the radio receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I149-1 (RR+) - O18-1
    Always
    Below 1 Ω
    I149-3 (RR-) - O18-2
    Always
    Below 1 Ω
    I149-2 (RL+) - O21-1
    Always
    Below 1 Ω
    I149-6 (RL-) - O21-2
    Always
    Below 1 Ω

  1. Measure the resistance between the radio receiver assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I148-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    I148-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    I148-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    I148-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    I149-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    I149-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    I149-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    I149-6 (RL-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I1-3 (+) - Body ground
    Always
    10 kΩ or higher
    I1-1 (-) - Body ground
    Always
    10 kΩ or higher
    I83-3 (+) - Body ground
    Always
    10 kΩ or higher
    I83-1 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E219303E36
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K5-1 - K5-2
      Always
      3.2 to 4.8 Ω
      J5-1 - J5-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E226097E13
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I83-4 (TWR+) - I83-2 (TWR-)
      Always
      10 kΩ or higher
      I83-3 (+)- I83-4 (TWR+)
      Always
      Below 1 Ω
      I83-1 (-) - I83-2 (TWR-)
      Always
      Below 1 Ω
      I1-4 (TWL+) - I1-2 (TWL-)
      Always
      10 kΩ or higher
      I1-3 (+) - I1-4 (TWL+)
      Always
      Below 1 Ω
      I1-1 (-) - I1-2 (TWL-)
      Always
      Below 1 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
  1. Check that the malfunction disappears when a known good speaker is installed (Click here).

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 5
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE) 

5.INSPECT REAR SPEAKER ASSEMBLY


    E219303E37
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O21-1 - O21-2
      Always
      3.2 to 4.8 Ω
      O18-1 - O18-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)