Home › Drivetrain ยท U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE FLUID

AUTOMATIC TRANSAXLE FLUID > REPLACEMENT

for Preparation Click here



1. REPLACE AUTOMATIC TRANSAXLE FLUID
  1. Lift the vehicle. [*1]

    NOTICE:
    Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the tilt angle from the front to rear of the vehicle is within +/- 1°).

  1. Remove the front wheel opening extension pad LH, engine under cover LH and front fender apron seal LH.



    C201682
  1. Remove the refill plug and gasket from the automatic transaxle assembly. [*2]



    C201683E03
  1. Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle assembly. [*3]
    Text in Illustration 
    *1
    No. 1 Transmission Oil Filler Tube
    *2
    Overflow Plug
    *3
    Hexagon Socket Wrench



    C201684E04
  1. Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle oil pan sub-assembly and drain the automatic transaxle fluid. [*4]
    Text in Illustration 
    *1
    No. 1 Transmission Oil Filler Tube
    *2
    Hexagon Socket Wrench
    *a
    Overflow Plug Hole



    C239510
  1. Measure the amount of fluid drained. [*5]

    HINT:
    Add the same amount of fluid in step [*8].

  1. Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle oil pan sub-assembly. [*6]

    Torque:
    0.8 N*m{ 8 kgf*cm , 7 in.*lbf }



    C201687
  1. Temporarily install the gasket and the overflow plug. [*7]

    HINT:
    Reuse the old gasket as the plug will be removed again to adjust the fluid level.



    C239936
  1. Add fluid to the refill hole using the same amount of fluid drained in step [*5]. [*8]

    NOTICE:
    Use Toyota Genuine ATF WS.



    C201682
  1. Temporarily install the gasket and refill plug to avoid fluid spillage. [*9]

    HINT:
    Reuse the old gasket as the plug will be removed again to adjust the fluid level.

  1. Lower the vehicle. [*10]

  1. Start the engine. [*11]

  1. Slowly move the shift lever from P to D, then back to P (keep the shift lever in each position for approximately 3 seconds). [*12]

    HINT:
    Slowly move the shift lever to circulate the fluid through each part of the automatic transaxle assembly.

  1. Allow the engine to idle for 30 seconds to warm it up. [*13]

  1. Turn the ignition switch off. [*14]

  1. Repeat steps [*1] to [*14].

  1. Repeat steps [*1] to [*10].



2. ADJUST FLUID TEMPERATURE (for Using the Techstream)

HINT:
The actual ATF temperature can be checked on the Data List using the Techstream.

  1. Connect the Techstream to the DLC3 with the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

    NOTICE:
    To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, are off.

  1. Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1

  1. Select the Data List menu: A/T Oil Temperature 1

  1. Select the Active Test menu: Connect the TC and TE1 / ON

  1. Check the ATF temperature.

    NOTICE:
    1. If the fluid temperature is below 45°C (113°F), proceed to the next step. [Recommended ATF temperature: 35°C (95°F) or less]
    2. If the fluid temperature is 45°C (113°F) or more, turn the ignition switch off and wait until the fluid temperature drops below 45°C (113°F).

  1. Depress and hold the brake pedal.

  1. Start the engine.

  1. Slowly move the shift lever from P to D, then back to P (keep the shift lever in each position for approximately 3 seconds).

    HINT:
    Slowly move the shift lever to circulate the fluid through each part of the automatic transaxle assembly.



    C240096E01
  1. While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.
    Text in Illustration 
    *a
    Optitron and Analog Type
    *b
    Analog Type

    NOTICE:
    Do not pause for more than 1.5 seconds.

    HINT:
    Performing this operation will cause the vehicle to enter fluid temperature detection mode.

  1. Check that the D shift indicator comes on for 2 seconds.

    HINT:
    1. When fluid temperature detection mode is activated, the D shift indicator on the combination meter comes on for 2 seconds.
    2. If the D shift indicator does not come on for 2 seconds, return to the first step and perform the procedure again.

  1. Move the shift lever from N to P.

  1. Release the brake pedal.

  1. Select the Active Test menu: Connect the TC and TE1 / OFF

    NOTICE:
    Be sure that terminals TC and TE1 are off. If the terminals are on, the fluid level cannot be precisely adjusted due to fluctuations in engine speed.

    HINT:
    1. Disconnecting terminals TC and TE1 activates engine idle speed control mode.
    2. In engine idle speed control mode, engine idle speed control starts when the fluid temperature becomes 35°C (95°F) or more and the engine speed is maintained at approximately 800 rpm.
    3. Even after terminals TC and TE1 are disconnected, fluid temperature detection mode is active until the ignition switch is turned off.



    C240097E01
  1. Warm up the engine with the engine idling until the fluid temperature reaches the fluid level adjustment temperature [35 to 45°C (95 to 113°F)].
    Below Fluid Level Adjustment Temperature
    Fluid Level Adjustment Temperature
    Above Fluid Level Adjustment Temperature
    35°C or less (95°F or less)
    35 to 45°C (95 to 113°F)
    45°C or more (113°F or more)
    Shift Indicator (D)
    Turned off
    Shift Indicator (D)
    Turned on
    Shift Indicator (D)
    Blinking
    Text in Illustration 
    *a
    Optitron and Analog Type
    *b
    Analog Type
    *c
    Turned Off
    *d
    Turned On
    *e
    Blinking

    NOTICE:
    1. If the fluid temperature is within the fluid level adjustment temperature range, immediately proceed to the "Adjust Fluid Level" procedure.
    2. If the fluid temperature is 45°C (113°F) or more, stop the engine and wait until the fluid temperature drops to 35°C (95°F) or less. Then perform the "Adjust Fluid Temperature" procedure again from the beginning.

    HINT:
    In fluid temperature detection mode, the D shift indicator comes on, goes off, or blinks depending on the fluid temperature.



3. ADJUST FLUID TEMPERATURE (for not Using the Techstream)


    C101492E05
  1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the ignition switch off.
    Text in Illustration 
    *1
    DLC3

    SST
    09843-18040  

  1. Depress and hold the brake pedal.

  1. Start the engine.

    NOTICE:
    To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, are off.

    HINT:
    The indicator lights on the combination meter blink to indicate the DTC output when terminals TC and CG are connected.

  1. Slowly move the shift lever from P to D, then back to P.

    HINT:
    Slowly move the shift lever to circulate the fluid through each part of the automatic transaxle assembly.



    C240096E01
  1. While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.
    Text in Illustration 
    *a
    Optitron and Analog Type
    *b
    Analog Type

    NOTICE:
    Do not pause for more than 1.5 seconds.

    HINT:
    Performing this operation will cause the vehicle to enter fluid temperature detection mode.

  1. Check that the D shift indicator comes on for 2 seconds.

    HINT:
    1. When fluid temperature detection mode is activated, the D shift indicator on the combination meter comes on for 2 seconds.
    2. If the D shift indicator does not come on for 2 seconds, return to the first step and perform the procedure again.

  1. Move the shift lever from N to P.

  1. Release the brake pedal.

  1. Remove SST from terminals 13 (TC) and 4 (CG).

    NOTICE:
    Be sure that terminals TC and CG are not connected. If the terminals are connected, the fluid level cannot be precisely adjusted due to fluctuations in engine speed.

    HINT:
    1. Disconnecting terminals TC and CG activates engine idle speed control mode.
    2. In engine idle speed control mode, engine idle speed control starts when the fluid temperature becomes 35°C (95°F) or more and the engine speed is maintained at approximately 800 rpm.
    3. Even after terminals TC and CG are disconnected, fluid temperature detection mode is active until the ignition switch is turned off.



    C240097E01
  1. Allow the engine to idle until the D shift indicator comes on again.
    Below Fluid Level Adjustment Temperature
    Fluid Level Adjustment Temperature
    Above Fluid Level Adjustment Temperature
    35°C or less (95°F or less)
    35 to 45°C (95 to 113°F)
    45°C or more (113°F or more)
    Shift Indicator (D)
    Turned off
    Shift Indicator (D)
    Turned on
    Shift Indicator (D)
    Blinking
    Text in Illustration 
    *a
    Optitron and Analog Type
    *b
    Analog Type
    *c
    Turned Off
    *d
    Turned On
    *e
    Blinking

    NOTICE:
    1. If the D shift indicator is on, immediately proceed to the "Adjust Fluid Level" procedure.
    2. If the D shift indicator blinks, stop the engine and wait until the fluid temperature drops to 35°C (95°F) or less (the indicator goes off). Then perform the "Adjust Fluid Temperature" procedure again from the beginning.

    HINT:
    1. In fluid temperature detection mode, the D shift indicator comes on, goes off, or blinks depending on the fluid temperature.
    2. Fluid filling procedure should be performed when the D shift indicator is on (the fluid temperature is within the fluid level adjustment temperature range).



4. ADJUST FLUID LEVEL

CAUTION:
Use caution while the engine is idling and the radiator fan is operating.

  1. Lift the vehicle.

    NOTICE:
    Set the vehicle on a lift so that the vehicle is kept level when it is lifted up.



    C201683E03
  1. Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket.
    Text in Illustration 
    *1
    No. 1 Transmission Oil Filler Tube
    *2
    Overflow Plug
    *3
    Hexagon Socket Wrench

    CAUTION:
    Be careful as the fluid coming out of the overflow plug hole is hot.

  1. Check the amount of fluid that comes out of the overflow plug hole.

    NOTICE:
    If only a small amount of fluid (approximately 1 cc) comes out of the overflow plug hole, then only fluid remaining in the No. 1 transmission oil filler tube has come out. This condition is not considered as overflow, so it is necessary to add fluid.



  1. If the fluid overflows



      C201682
    1. Remove the refill plug and gasket.



    2. C201690
    3. Wait until the fluid flow slows and only drips come out.



  1. If the fluid does not overflow



      C201682
    1. Remove the refill plug and gasket.



    2. C201685
    3. Add transaxle fluid through the refill hole until fluid comes out of the overflow plug hole.



    4. C201686
    5. Wait until the fluid flow slows and only drips come out.



    C201683E03
  1. Install the overflow plug with a new gasket.
    Text in Illustration 
    *1
    No. 1 Transmission Oil Filler Tube
    *2
    Overflow Plug
    *3
    Hexagon Socket Wrench

    Torque:
    40 N*m{ 408 kgf*cm , 29 ft.*lbf }



    C201682
  1. Install the refill plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Lower the vehicle.

  1. Turn the ignition switch off.

    HINT:
    Turning the ignition switch off exits fluid temperature detection mode.

  1. Remove the Techstream from the DLC3 (when using the Techstream).



5. REBUILD WORK
  1. Lift the vehicle.

  1. Clean each part.

  1. Check for fluid leaks.

  1. Install the front wheel opening extension pad LH, engine under covers LH and front fender apron seal LH.

  1. Lower the vehicle.