Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > CUSTOMIZE PARAMETERS

for Preparation Click here



1. CUSTOMIZE LIGHTING SYSTEM (EXT)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the Techstream

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Body Electrical / Main Body / Utility / Customize / Light Control.

    5. Select the setting by referring to the table below.

      Light Control 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Disp Ex ON Sen
      NORMAL
      Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*A
      LIGHT2, LIGHT1, NORMAL, DARK1 or DARK2
      Main Body ECU (Multiplex Network Body ECU)
      Disp Ex OFF Sen
      NORMAL
      Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*B
      LIGHT2, LIGHT1, NORMAL, DARK1 or DARK2
      Light Auto OFF Delay
      30 s
      Keeps the headlights on for a certain period of time after turning the ignition switch off and closing all doors with the low beam headlights on.
      OFF, 30 s, 60 s or 90 s
      Response Time*1
      Normal
      Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position.
      Normal or Long
      Sensitivity
      Normal
      Adjusts the sensitivity of the automatic light control system.*C
      Light2, Light1, Normal, Dark1 or Dark2
      DRL Function*2
      ON
      ON/OFF of the DRL function
      ON or OFF

      1. *1: w/o DRL
      2. *2: Headlight dimmer switch with DRL OFF function.

      HINT:
      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


      *A 
      Brightness level required to dim the lights

      E107164

      Setting
      DARK2
      DARK1
      NORMAL
      LIGHT1
      LIGHT2

      *B 
      Brightness level required to cancel the dimming of the lights

      E107164

      Setting
      DARK2
      DARK1
      NORMAL
      LIGHT1
      LIGHT2

      *C 
      Sensitivity of the automatic light control system

      E107164

      Setting
      Dark2
      Dark1
      Normal
      Light1
      Light2

  1. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type) or w/ Audio and Visual System (for Radio and Display Type with Intuitive Parking Assist System))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Light Settings.

    3. Select the setting by referring to the table below.

      Light Settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Headlamps-On Sensitivity
      0
      Adjusts the sensitivity of the automatic light control system.*A
      -2, -1, 0, +1 or +2
      Main Body ECU (Multiplex Network Body ECU)
      Headlamps Auto-Off Timer
      30 sec.
      Keeps the headlights on for a certain period of time after turning the ignition switch off and closing all doors with the low beam headlights on.
      Off, 30 sec., 60 sec. or 90 sec.
      Daytime Running Lights*1
      On
      ON/OFF of the DRL function
      On or Off

      1. *1: Headlight dimmer switch with DRL OFF function.

      HINT:
      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


      *A 
      Sensitivity of the automatic light control system

      E107164

      Setting
      -2
      -1
      0
      +1
      +2

  1. Customizing with the multi-display (w/ Navigation System (for Radio and Display Type) or w/ Audio and Visual System (for Radio and Display Type without Intuitive Parking Assist System))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: SETUP / Vehicle.

    3. Select the setting by referring to the table below.

      Vehicle Settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Light Sensor Sensitivity
      0
      Adjusts the sensitivity of the automatic light control system.*A
      -2, -1, 0, +1 or +2
      Main Body ECU (Multiplex Network Body ECU)
      Headlight Off Time Adjust
      30 sec.
      Keeps the headlights on for a certain period of time after turning the ignition switch off and closing all doors with the low beam headlights on.
      Off, 30 sec., 60 sec. or 90 sec.
      Daytime Running Lights*1
      On
      ON/OFF of the DRL function
      On or Off

      1. *1: Headlight dimmer switch with DRL OFF function.

      HINT:
      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


      *A 
      Sensitivity of the automatic light control system

      E107164

      Setting
      -2
      -1
      0
      +1
      +2