Home › General › INTRODUCTION › REPAIR INSTRUCTION

REPAIR INSTRUCTION > CUSTOMIZE PARAMETERS



1. CUSTOMIZE INTUITIVE PARKING ASSIST SYSTEM
  1. Customizing with the Techstream

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Be sure to make a note of the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Connect the Techstream to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the clearance sonar main switch on.

    4. Turn the Techstream on.

    5. Enter the following menus: Body Electrical / Utility / Customize / Sensor

    6. Select the setting by referring to the table below.

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Rr Sensor Onset Range
      Wide
      Sets the buzzer activation range for the rear center sensors.
      Narrow or Wide
      1. Narrow: 600 mm (23.6 in.)
      2. Wide: 1000 mm (39.4 in.) (Pole)
      3. Wide: 1500 mm (59.1 in.) (Wall)
      Clearance warning ECU assembly
      Keep Sense Buzzer
      Avail
      Sounds the buzzer when the distance between the vehicle and obstacle does not change for more than 3 seconds.
      Not Avail or Avail
      1. Not Avail: Not Available
      2. Avail: Available
      Clearance warning ECU assembly
      Fr & Rr Buzzer Volume
      M2
      Changes the buzzer volume setting.
      L, M1, M2, M3 or H
      1. L: Low volume
      2. M1: Medium low volume
      3. M2: Medium volume
      4. M3: Medium high volume
      5. H: High volume
      Clearance warning ECU assembly

      Sensor 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Sensor Condition N
      Avail
      Makes the front sensors available when the shift lever is in N.
      Not Avail or Avail
      1. Not Avail: Not Available
      2. Avail: Available
      Clearance warning ECU assembly
      Reverse Range Front Sensor
      F
      Changes the operation setting for the front sensors when the shift lever is in R.
      F or F Stop
      1. F: Front sensors are available
      2. F Stop: Front sensors are not available
      Clearance warning ECU assembly
      Non P/R Range Rear Sensor
      R Stop
      Changes the operation setting for the rear sensors when the shift lever is in any position other than P or R.
      R, Rcrn or R Stop
      1. R: All rear sensors are available
      2. Rcrn: Rear corner sensors are available
      3. R Stop: All rear sensors are not available
      Clearance warning ECU assembly



2. CUSTOMIZE POWER DOOR LOCK CONTROL SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the Techstream

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Customize Setting / Door Lock.

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Unlock Key Twice
      ON
      Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlocks all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Auto Lock
      ON*1
      OFF*2
      Function that locks all doors when the vehicle speed reaches a certain level.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Auto Lock/Shift
      ON*2
      OFF*1
      Function that locks all doors when the shift lever is moved out of P, with the ignition switch ON and all doors closed.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Auto Unlock/Shift
      ON
      Function that unlocks all doors when the shift lever is moved to P from any position other than P with the ignition switch ON.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      All Unlock/Open-Close
      OFF
      Function that unlocks the other doors when the driver door is opened within 10 seconds after the ignition switch is turned off.
      OFF or ON
      Main body ECU (Multiplex network body ECU)

      1. *1: w/o Daytime Running Light Control
      2. *2: w/ Daytime Running Light Control

  1. Customizing with the Multi-display (w/ Navigation System (for Navigation Receiver Type) or Audio and Visual System (for Radio and Display Type with Intuitive Parking Assist System))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: SET UP/ Vehicle / Vehicle Customization / Door Lock Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Unlock on Second Key Turn
      On
      Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlocks all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto Lock by Speed
      On*1
      Off*2
      Function that locks all doors when the vehicle speed reaches a certain level.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto Lock by Shift from P
      On*2
      Off*1
      Function that locks all doors when the shift lever is moved out of P, with the ignition switch ON and all doors closed.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto Unlock by Shift to P
      On
      Function that unlocks all doors when the shift lever is moved to P from any position other than P with the ignition switch ON.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto Unlock by Driver Door
      Off
      Function that unlocks the other doors when the driver door is opened within 10 seconds after the ignition switch is turned off.
      On or Off
      Main body ECU (Multiplex network body ECU)

      1. *1: w/o Daytime Running Light Control
      2. *2: w/ Daytime Running Light Control

  1. Customizing with the Multi-display (w/ Navigation System (for Radio and Display Type) or w/ Audio and Visual System (for Radio and Display Type without Intuitive Parking Assist System))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: SET UP/ Vehicle.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Speed Sensitive Auto Lock
      Off
      Function that locks all doors when the vehicle speed reaches a certain level.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Shift- Linked Auto Lock
      Off
      Function that locks all doors when the shift lever is moved out of P, with the ignition switch ON and all doors closed.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Shift-Linked Auto Unlock
      On
      Function that unlocks all doors when the shift lever is moved to P from any position other than P with the ignition switch ON.
      On or Off
      Main body ECU (Multiplex network body ECU)



3. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Key System)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the Techstream

    1. Connect the Techstream to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the Techstream on.

    4. Enter the following menus: Customize Setting / Wireless Door Lock.

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Wireless Control
      ON
      Function that turns wireless door lock
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Hazard Answer Back
      ON
      When the doors are locked by wireless operation, the hazard warning lights flash once.
      When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Open Door Warning
      ON
      The buzzer sounds when lock is pressed when any of the doors are ajar.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Unlock 2 Operation
      ON
      Function that unlocks driver door when unlock switch on electrical key transmitter sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Panic Function
      ON
      Function to operate theft deterrent system by continuously pressing panic switch on electrical key transmitter sub-assembly for 0.8 seconds
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Trunk Lid Operation
      Long1
      Function to change the operation method of opening the luggage compartment door by the electrical key transmitter sub-assembly.
      1tim ON: Push the luggage open switch once
      2tim ON: Push the luggage open switch twice
      Long1: Push the luggage open switch for 0.8 seconds
      Long2: Push the luggage open switch for 1.6 seconds
      Prohibit: Wireless luggage compartment door open function is off
      1tim ON, 2tim ON, Long1, Long2 or Prohibit
      Main body ECU (Multiplex network body ECU)
      Auto Lock Time
      60 s*1
      30 s*2
      Function that regulates the interval between unlocking and automatic relocking of doors
      30 s, 60 s or 120 s
      Main body ECU (Multiplex network body ECU)
      Wireless Auto Lock*1
      ON
      This function turns the wireless auto lock function on or off.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Resp
      ON
      Wireless door lock buzzer response
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      P/W Wireless Ope Buzz*1
      ON
      Wireless power window buzzer response
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Vol
      Level 5
      Wireless door lock buzzer volume
      Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level0
      Main body ECU (Multiplex network body ECU)

      1. *1: w/ Daytime Running Light Control
      2. *2: w/o Daytime Running Light Control

  1. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type) or Audio and Visual System (for Radio and Display Type and with Intuitive Parking Assist System))

    1. Turn the engine switch on (IG).

    2. Enter the following menus: SET UP/ Vehicle / Vehicle Customization / Door Lock Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Remote 2-Press Unlock
      On
      Function that unlocks driver door when unlock switch on electrical key transmitter sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto Relock Timer*
      60 s
      Function that regulates the interval between unlocking and automatic relocking of doors
      30 s, 60 s or 120 s
      Main body ECU (Multiplex network body ECU)
      Lock/Unlock Feedback-Lights
      On
      When the doors are locked by wireless operation, the hazard warning lights flash once.
      When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock/Unlock Feedback-Tone
      5
      Wireless door lock buzzer volume
      0, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)

      1. *: w/ Daytime Running Light Control

  1. Customizing with the multi-display (w/ Navigation System (for Radio and Display Type) or w/ Audio and Visual System (for Radio and Display Type and without Intuitive Parking Assist System))

    1. Turn the engine switch on (IG).

    2. Enter the following menus: SET UP / Vehicle.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Remote 2-Press Unlock
      On
      Function that unlocks driver door when unlock switch on electrical key transmitter sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock Feedback Volume
      5
      Wireless door lock buzzer volume
      0, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)



4. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the Techstream

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Customize Setting / Wireless Door Lock.

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Wireless Control
      ON
      Function that turns wireless door lock
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Hazard Answer Back
      ON
      When the doors are locked by wireless operation, the hazard warning lights flash once.
      When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Open Door Warning
      ON
      The buzzer sounds when lock is pressed when any of the doors are ajar.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Unlock 2 Operation
      ON
      Function that unlocks driver door when unlock switch on door control transmitter module set sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Panic Function
      ON
      Function to operate theft deterrent system by continuously pressing panic switch on door control transmitter module set sub-assembly for 0.8 seconds
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Trunk Lid Operation
      Long1
      Function to change the operation method of opening the luggage compartment door by the door control transmitter module set sub-assembly.
      1tim ON: Push the luggage open switch once
      2tim ON: Push the luggage open switch twice
      Long1: Push the luggage open switch for 0.8 seconds
      Long2: Push the luggage open switch for 1.6 seconds
      Prohibit: Wireless luggage compartment door open function is off
      1tim ON, 2tim ON, Long1, Long2 or Prohibit
      Main body ECU (Multiplex network body ECU)
      Auto Lock Time
      60 s
      Function that regulates the interval between unlocking and automatic relocking of doors
      30 s, 60 s or 120 s
      Main body ECU (Multiplex network body ECU)
      Wireless Auto Lock
      ON
      This function turns the wireless auto lock function on or off.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Resp
      ON
      Wireless door lock buzzer response
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      P/W Wireless Ope Buzz
      ON
      Wireless power window buzzer response
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Vol
      Level 5
      Wireless door lock buzzer volume
      Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level 0
      Main body ECU (Multiplex network body ECU)

  1. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: SET UP / Vehicle / Vehicle Customization / Door Lock Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Remote 2-Press Unlock
      On
      Function that unlocks driver door when unlock switch on door control transmitter module set sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is off, pressing unlock switch once makes all doors unlock.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto Relock Timer
      60 s
      Function that regulates the interval between unlocking and automatic relocking of doors
      30 s, 60 s or 120 s
      Main body ECU (Multiplex network body ECU)
      Lock/Unlock Feedback-Lights
      On
      When the doors are locked by wireless operation, the hazard warning lights flash once.
      When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock/Unlock Feedback-Tone
      5
      Wireless door lock buzzer volume
      0, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)

  1. Customizing with the multi-display (w/ Navigation System (for Radio and Display Type) or w/ Audio and Visual System (for Radio and Display Type and without Intuitive Parking Assist System))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: SET UP / Vehicle.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Remote 2-Press Unlock
      On
      Function that unlocks driver door when unlock switch on door control transmitter module set sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is off, pressing unlock switch once makes all doors unlock.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock Feedback Volume
      5
      Wireless door lock buzzer volume
      0, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)



5. CUSTOMIZE SMART KEY SYSTEM (for Entry Function)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Record the current settings before customizing.

  1. Customizing with the Techstream

    1. Connect the Techstream to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the Techstream on.

    4. Enter the following menus: Customize Setting / Wireless Door Lock, Smart Key/Access or Warning.

    5. Select the setting by referring to the table below.

      Wireless Door Lock 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Hazard Answer Back
      ON
      When the doors are locked by entry function, the hazard warning lights flash once.
      When the doors are unlocked by entry function, the hazard warning lights flash twice.
      OFF or ON
      Main body ECU (multiplex network body ECU)
      Open Door Warning
      ON
      The buzzer sounds when the lock sensor on the door outside handle assembly is touched to perform entry lock with a door open.
      OFF or ON
      Main body ECU (multiplex network body ECU)
      Auto Lock Time
      30 s*1
      60 s*2
      Function that regulates the interval between unlocking and automatic relocking of doors.
      30 s, 60 s or 120 s
      Main body ECU (multiplex network body ECU)
      Wireless Auto Lock*2
      ON
      This function turns the auto lock function on or off.
      OFF or ON
      Main body ECU (multiplex network body ECU)
      Wireless Buzzer Resp
      ON
      Function that sounds the answer-back buzzer when an entry lock or unlock operation is performed.
      OFF or ON
      Main body ECU (multiplex network body ECU)
      Wireless Buzzer Vol
      Level 5
      Buzzer answer back volume
      Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level0
      Main body ECU (multiplex network body ECU)

      1. *1: w/o Daytime Running Light Control
      1. *2: w/ Daytime Running Light Control

      Smart Key/Access 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Park Wait Time (Waiting time to permit unlocking door after locking)
      2.5s
      Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed.
      0.5s, 1.5s, 2.5s or 5s
      Certification ECU (smart key ECU assembly)
      Ignition Available Area
      (Entry ignition available area)
      All
      Function that sets the area that the key must be in before the engine switch can be operated.
      Front or All
      Certification ECU (smart key ECU assembly)
      Trunk Open Mode
      ON
      Function that opens the luggage compartment door when the driver has the electrical key transmitter sub-assembly and presses the luggage door opening switch assembly.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      Door Unlock Mode2
      Driver
      Function that chooses the doors to be operated by entry unlock operation.
      All or Driver
      Certification ECU (smart key ECU assembly)
      Auto Entry Cancel SW*
      OFF
      Function that enables or disables the smart key system.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      Touch Activation Over Threshold
      Active
      The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed.
      Active or Not Active
      Certification ECU (smart key ECU assembly)
      Engine Start Indicator
      ON
      Function that turns the smart warning light on the combination meter assembly on or off.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      1. *: w/o Daytime Running Light Control

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Key Low Battery Warning (Warn when key battery becomes weak)
      ON
      Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more.
      OFF or ON
      Certification ECU (smart key ECU assembly)

  1. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type) or w/ Audio and Visual System (for Radio and Display Type with Intuitive Parking Assist System))

    1. Turn the engine switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Select Doors to Unlock
      Driver's Door
      Function that sets which doors are unlocked by the entry unlock function.
      All Doors or Driver's Door
      Certification ECU (smart key ECU assembly)
      Entry and Start System*
      On
      Function that enables or disables the smart key system.
      On or Off
      Certification ECU (smart key ECU assembly)

      1. *: w/o Daytime Running Light Control



  1. Entry unlock mode switching function (manual operation)

    1. The following entry unlock modes can be selected when using the entry unlock mode switching function.

      1. All door unlock mode: When the sensor of a front door outside handle assembly is touched, an entry unlock operation is performed simultaneously for all doors.
      2. Driver door unlock mode: When the sensor of the driver side door outside handle assembly is touched, an entry unlock operation is performed for the driver door only. If any other door handle is touched, an entry unlock operation is performed simultaneously for all doors.



    2. When customizing through manual operation:

      1. Turn the engine switch off.
      2. Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock buttons of the electrical key transmitter sub-assembly for 5 seconds or more while the electrical key transmitter sub-assembly is in the actuation area.
      3. Check the current setting.

        HINT:
        1. The mode changes from all door unlock mode to driver door unlock mode and then back to all door unlock mode.
        2. The answer-back (wireless buzzer, buzzer in the combination meter assembly) operation for each mode is indicated in the table below.

          Currently Selected Mode
          Answer-back (Wireless Buzzer)
          Answer-back (Buzzer in Combination Meter Assembly)
          All door unlock mode
          Buzzer sounds twice (short beeps)
          Buzzer sounds once
          Driver door unlock mode
          Buzzer sounds 3 times (short beeps)
          Buzzer sounds once

      4. Release the lock and unlock buttons of the electrical key transmitter sub-assembly.
      5. Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock buttons of the electrical key transmitter sub-assembly for 5 seconds or more to change the mode.

        HINT:
        Repeat the procedure as necessary to select the desired mode.

      6. Unlock the doors with the wireless operation, and then open any door


      B274853E01

  1. Entry cancel function (manual operation)

    HINT:
    While the smart key system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.


    1. The following functions are disabled when the smart key system is canceled.

      1. Entry unlock/lock functions
      2. Entry luggage compartment door open function
      3. Push start function
      4. Key lock-in prevention function
      5. Entry warning functions

    2. When canceling the system through manual operation:

      1. Make sure the following conditions are met:
        1. The engine switch is off.
        2. The driver door is closed.
        3. The driver door is unlocked.
      2. Press the unlock button of the electrical key transmitter sub-assembly.
      3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).
      4. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      5. Close and open the driver door twice completing the above step (driver door: open condition → closed → opened → closed → opened).
      6. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      7. Close and open the driver door completing the step above (driver door: open condition → closed → opened).
      8. Close the driver door within 5 seconds of completing the above step.
      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart key system has been canceled.

      HINT:
      Finish the step 5 to 7 within 30 seconds.

    3. Perform the following procedure to restore the smart key system to the active state from the canceled state.

      1. Perform the procedures to cancel the smart key system again.
      2. Check that the wireless buzzer sounds once (short beep) to confirm that the smart key system has been restored to the active state.

        HINT:
        1. The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.
        2. The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.



6. CUSTOMIZE SMART KEY SYSTEM (for Start Function)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Record the current settings before customizing.

  1. Customizing with the Techstream

    1. Connect the Techstream to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the Techstream on.

    4. Enter the following menus: Customize Setting / Smart Key/Access or Warning.

    5. Select the setting by referring to the table below.

      Smart Key/Access 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Ignition Available Area
      (Entry ignition available area)
      All
      Function that sets the area that the key must be in before the engine switch can be operated.
      Front or All
      Certification ECU (smart key ECU assembly)
      Engine Start Indicator
      ON
      Function that turns the smart warning light on the combination meter assembly on or off.
      OFF or ON
      Certification ECU (smart key ECU assembly)

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Key Low Battery Warning (Warn when key battery becomes weak)
      ON
      Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more.
      OFF or ON
      Certification ECU (smart key ECU assembly)

  1. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type) or Audio and Visual System (for Radio and Display Type and with Intuitive Parking Assist System))

    1. Turn the engine switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Entry and Start System*
      On
      Function that enables or disables the smart key system.
      On or Off
      Certification ECU (smart key ECU assembly)

      1. *: w/o Daytime Running Light Control

  1. Entry cancel function (manual operation)

    HINT:
    While the smart key system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.


    1. The following functions are disabled when the smart key system is canceled.

      1. Entry unlock/lock functions
      2. Entry luggage compartment door open function
      3. Push-button start function
      4. Key lock-in prevention function
      5. Entry warning functions

    2. When canceling the system through manual operation:

      1. Make sure the following conditions are met:
        1. The engine switch is off.
        2. The driver door is closed.
        3. The driver door is unlocked.
      2. Press the unlock button of the electrical key transmitter sub-assembly.
      3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).
      4. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      5. Close and open the driver door twice completing the above step (driver door: open condition → closed → opened → closed → opened).
      6. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      7. Close and open the driver door completing the step above (driver door: open condition → closed → opened).
      8. Close the driver door within 5 seconds of completing the above step.
      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart key system has been canceled.

      HINT:
      Finish the step 5 to 7 within 30 seconds.

    3. Perform the following procedure to restore the smart key system to the active state from the canceled state.

      1. Perform the procedures to cancel the smart key system again.
      2. Check that the wireless buzzer sounds once (short beep) to confirm that the smart key system has been restored to the active state.

        HINT:
        1. The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.
        2. The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.



7. CUSTOMIZE THEFT DETERRENT SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the Techstream

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Customize Setting / Security.

    5. Select the setting by referring to the table below.

      Security 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Panic Function
      ON
      This function operates the theft deterrent system when the panic switch is pressed and held for 0.8 seconds.
      ON or OFF
      Main Body ECU (Multiplex Network Body ECU)
      Security control with mechanism key*
      OFF
      This function makes it possible to cancel the security alarm with the mechanical key.
      ON or OFF

      1. *: w/o Daytime Running Light Control and w/ Smart Key System



8. CUSTOMIZE REMOTE ENGINE STARTER SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the Techstream

    1. Connect the Techstream to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the Techstream on.

    4. Enter the following menus: Customize Setting / Air Conditioner.

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Air Conditioner Mode
      User
      This function controls the air conditioner when the remote engine start function is operating.
      User/Auto
      Remote Engine Starter ECU
      Defogger Control
      OFF
      This function controls the window defogger operation when the remote engine start function is operating.
      OFF/ON



9. CUSTOMIZE LIGHTING SYSTEM (INT)
  1. Customizing using the Techstream

    HINT:
    The following items can be customized.

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Be sure to make a note of the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Customize Setting / Illuminated Entry.

    5. Select the setting by referring to the table below.

      Illuminated Entry 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Lighting Time
      15 s
      Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the ignition switch from off to ACC or ON.)
      7.5 s, 15 s or 30 s
      Main body ECU (Multiplex network body ECU)
      I/L when ACC OFF
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2, personal light*3 and rear interior light when the ignition switch is turned from ACC or ON to off.
      ON or OFF
      I/L ON W/Door Key Unlock
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2, personal light*3 and rear interior light when doors are unlocked using a mechanical key or door control transmitter.
      ON or OFF
      Room Light when Aprchd
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2, personal light*3 and rear interior light when a key enters any actuation area around the doors.
      ON or OFF
      Interior Light Control
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2, personal light*3 and rear interior light when the illuminated entry function is operating.
      ON or OFF

      1. *1: w/ Smart Key System
      2. *2: w/o Smart Key System
      3. *3: w/ Sliding Roof

  1. Customizing using the Multi-display (w/ Navigation System (for Navigation Receiver Type) or w/ Audio and Visual System (for Radio and Display Type with Intuitive Parking Assist System))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: Setup / Vehicle / Vehicle Customization / Light Settings

    3. Select the setting by referring to the table below:

      Display
      Default
      Content
      Setting
      Relevant ECU
      Interior Lights Off Timer
      15 sec.
      Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the ignition switch from off to ACC or ON.)
      Off, 7.5 sec., 15 sec., or 30 sec.
      Main body ECU (Multiplex network body ECU)



10. CUSTOMIZE METER / GAUGE SYSTEM
  1. Customizing with the Techstream

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Customize Setting / Warning.

    5. Select the setting by referring to the table below.

      NOTICE:
      1. Be sure to record the current value before customizing.


      Warning 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Key Remind Sound
      Slow
      Function to change the cycle of the key remind warning buzzer
      Fast, Normal, Slow
      Combination meter assembly
      Driver Side Seatbelt Warning Buzzer*1
      ON
      Function to turn on/off the seat belt warning buzzer
      ON or OFF
      Combination meter assembly
      Front Passenger Side Seatbelt Warning Buzzer*1
      ON
      Function to turn on/off the seat belt warning buzzer
      ON or OFF
      Combination meter assembly
      1. *1: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more

  1. Customizing with the combination meter assembly

    HINT:
    1. Press and hold the DISP switch to enter an item.
    2. Briefly press the DISP switch to select an item.


    1. Turn the ignition switch to ON.

    2. Select the following menus: SETTINGS.

    3. Select the setting by referring to the table below.

      NOTICE:
      1. Be sure to record the current value before customizing.


      Settings 
      Combination meter assembly display
      Default
      Content
      Setting
      Relevant ECU
      LANGUAGE
      ENGLISH
      Function to change the multi-information display language
      ENGLISH, FRENCH, SPANISH
      Combination meter assembly
      ECO INDICATOR
      ON
      Function to change the illumination level
      ON or OFF
      Combination meter assembly

    4. Press and hold the DISP switch.

    5. Return to the item selection screen.



11. CUSTOMIZE SEAT BELT WARNING SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.
  4. These buzzers should be ON for safe driving. Perform this procedure only if it is necessary to set the buzzer to OFF (disabled).

  1. Customizing with the Techstream

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Customize Setting / Warning.

    5. Select the setting by referring to the table below.

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Driver Side Seatbelt Warning Buzzer
      ON
      Function to sound the driver seat belt warning buzzer
      ON/OFF
      Combination meter assembly
      Front Passenger Side Seatbelt Warning Buzzer
      ON
      Function to sound the front passenger seat belt warning buzzer
      ON/OFF

      HINT:
      This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.



12. CUSTOMIZE AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
  1. Customizing with the Techstream

    HINT:
    The following items can be customized.

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Be sure to make a note of the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Connect the Techstream.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Customize Setting / Air Conditioner.

    5. Select the setting by referring to the table below.

      Air Conditioner 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Set Temperature Shift
      Normal
      Function to perform control with the shifted temperature versus the displayed temperature
      -2C, -1C, Normal, +1C, +2C
      Air Conditioning Amplifier Assembly
      Evaporator Control
      Automatic
      Function to set the evaporator control to the AUTOMATIC position (AUTO) to save power or to the coldest position (MANUAL) to dehumidify the air and to prevent the windows from fogging up
      Automatic or Manual
      Air Conditioning Amplifier Assembly
      Compressor Mode
      Automatic
      Function to turn the A/C ON automatically by pressing the AUTO button when the blower is ON and the A/C is OFF
      Automatic or Manual
      Air Conditioning Amplifier Assembly
      Air Inlet Mode
      Automatic
      In case of turning the A/C ON to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode
      Automatic or Manual
      Air Conditioning Amplifier Assembly
      Foot/DEF Auto Mode
      ON
      Function to turn the airflow from FOOT/DEF ON automatically when AUTO MODE is ON
      ON or OFF
      Air Conditioning Amplifier Assembly
      Foot/DEF Automatic Blow Up Function
      ON
      Function to increase the blower level automatically when the defroster is ON
      ON or OFF
      Air Conditioning Amplifier Assembly
      Ambient Temperature Shift
      Normal
      Function to display shifted ambient temperature versus actual ambient temperature
      -3C, -2C, -1C, Normal, +1C, +2C, +3C
      Air Conditioning Amplifier Assembly
      Refrigerant Shortage Check
      ON
      Function to cancel the refrigerant shortage check (check performed during normal operation) when item is OFF.
      ON or OFF
      Air Conditioning Amplifier Assembly
      Fan speed increment control
      Normal
      Function to define how fast the AC blower goes to target speed when first activating the AC.
      Slow, Normal, Fast
      Air Conditioning Amplifier Assembly

  1. Customizing using the Multi-display (w/ Navigation System (for Navigation Receiver Type) or w/ Audio and Visual System (for Radio and Display Type with Intuitive Parking Assist System))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: SET UP / Vehicle / Vehicle Customization / Climate Settings

    3. Select the setting by referring to the table below:

      Display
      Default
      Content
      Setting
      Relevant ECU
      Auto A/C Mode
      On
      Function to turn the A/C ON automatically by pressing the AUTO button when the blower is ON and the A/C is OFF
      On or Off
      Air conditioning amplifier assembly
      Efficient Ventilation Mode
      On
      In case of turning the A/C ON to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode
      On or Off
      Air conditioning amplifier assembly



13. CUSTOMIZE AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)
  1. Customizing with the Techstream

    HINT:
    The following items can be customized.

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Be sure to make a note of the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Connect the Techstream.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Customize Setting / Air Conditioner.

    5. Select the setting by referring to the table below.

      Air Conditioner 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Evaporator Control
      Automatic
      Function to set the evaporator control to the AUTOMATIC position (AUTO) to save power or to the coldest position (MANUAL) to dehumidify the air and to prevent the windows from fogging up
      Automatic or Manual
      Air Conditioning Amplifier Assembly
      Refrigerant Shortage Check
      ON
      Function to cancel the refrigerant shortage check (check performed during normal operation) when item is OFF.
      ON or OFF
      Air Conditioning Amplifier Assembly



14. CUSTOMIZE POWER WINDOW CONTROL SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function(s) can be customized.
  2. Be sure to make notes of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the Techstream

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Customize Setting / Power Window.

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Door Key P/W Up
      OFF
      This function is used to close the windows by operating the mechanical key.
      OFF/ON
      Main body ECU (Multiplex network body ECU)
      Door Key P/W Down
      OFF
      This function is used to open the windows by operating the mechanical key.
      OFF/ON
      Main body ECU (Multiplex network body ECU)
      P/W Down W/ Transmit*1,*2
      OFF
      This function is used to open the windows using the wireless key transmitter.
      OFF/ON
      Main body ECU (Multiplex network body ECU)

      1. *1: w/ Daytime Running Light Control
      2. *2: w/ Wireless Door Lock Control System

    6. Enter the following menus: Customize Setting / Wireless Door Lock.

    7. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      P/W Ope buzzer*1,*2
      ON
      This function turns the wireless power window buzzer response on or off.
      OFF/ON
      Main body ECU (Multiplex network body ECU)

      1. *1: w/ Daytime Running Light Control
      2. *2: w/ Wireless Door Lock Control System



15. CUSTOMIZE SLIDING ROOF SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function(s) can be customized.
  2. Be sure to make notes of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the Techstream

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Customize Setting / Power Window.

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Door Key P/W Up
      OFF
      This function is used to close the driver door window and sliding roof by operating the mechanical key.
      OFF/ON
      Main body ECU (Multiplex network body ECU)
      Door Key P/W Down
      OFF
      This function is used to open the driver door window and sliding roof by operating the mechanical key.
      OFF/ON
      Main body ECU (Multiplex network body ECU)
      P/W Down W/ Transmit*1
      OFF
      This function is used to open the driver door window and sliding roof using the wireless key transmitter.
      OFF/ON
      Main body ECU (Multiplex network body ECU)

      1. *1: w/ Daytime Running Light Control

    6. Enter the following menus: Customize Setting / Slide Roof.

    7. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Door Key Related Operation
      Slide
      Function to select tilt up or slide open of sliding roof key-linked function.
      Slide/Tilt
      Sliding roof ECU (Sliding roof drive gear sub-assembly)
      Wireless Key Related Operation*1
      Slide
      Function to select tilt up or slide open of sliding roof wireless transmitter-linked function.
      Slide/Tilt
      Sliding roof ECU (Sliding roof drive gear sub-assembly)
      Front SW Auto Operation
      ON
      This function is used to enable or disable the auto operation.
      OFF/ON
      Sliding roof ECU (Sliding roof drive gear sub-assembly)

      1. *1: w/ Daytime Running Light Control

    8. Enter the following menus: Customize Setting / Security.

    9. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Slide Roof Open Warning
      ON
      This function is used to enable or disable the sliding roof open warning.
      OFF/ON
      Main body ECU (Multiplex network body ECU)



16. CUSTOMIZE LIGHTING SYSTEM (EXT)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the Techstream

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Body Electrical / Main Body / Utility / Customize / Light Control.

    5. Select the setting by referring to the table below.

      Light Control 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Disp Ex ON Sen
      NORMAL
      Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*A
      LIGHT2, LIGHT1, NORMAL, DARK1 or DARK2
      Main Body ECU (Multiplex Network Body ECU)
      Disp Ex OFF Sen
      NORMAL
      Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*B
      LIGHT2, LIGHT1, NORMAL, DARK1 or DARK2
      Light Auto OFF Delay
      30 s
      Keeps the headlights on for a certain period of time after turning the ignition switch off and closing all doors with the low beam headlights on.
      OFF, 30 s, 60 s or 90 s
      Response Time*1
      Normal
      Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position.
      Normal or Long
      Sensitivity
      Normal
      Adjusts the sensitivity of the automatic light control system.*C
      Light2, Light1, Normal, Dark1 or Dark2
      DRL Function*2
      ON
      ON/OFF of the DRL function
      ON or OFF

      1. *1: w/o DRL
      2. *2: Headlight dimmer switch with DRL OFF function.

      HINT:
      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


      *A 
      Brightness level required to dim the lights

      E107164

      Setting
      DARK2
      DARK1
      NORMAL
      LIGHT1
      LIGHT2

      *B 
      Brightness level required to cancel the dimming of the lights

      E107164

      Setting
      DARK2
      DARK1
      NORMAL
      LIGHT1
      LIGHT2

      *C 
      Sensitivity of the automatic light control system

      E107164

      Setting
      Dark2
      Dark1
      Normal
      Light1
      Light2

  1. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type) or w/ Audio and Visual System (for Radio and Display Type with Intuitive Parking Assist System))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Light Settings.

    3. Select the setting by referring to the table below.

      Light Settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Headlamps-On Sensitivity
      0
      Adjusts the sensitivity of the automatic light control system.*A
      -2, -1, 0, +1 or +2
      Main Body ECU (Multiplex Network Body ECU)
      Headlamps Auto-Off Timer
      30 sec.
      Keeps the headlights on for a certain period of time after turning the ignition switch off and closing all doors with the low beam headlights on.
      Off, 30 sec., 60 sec. or 90 sec.
      Daytime Running Lights*1
      On
      ON/OFF of the DRL function
      On or Off

      1. *1: Headlight dimmer switch with DRL OFF function.

      HINT:
      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


      *A 
      Sensitivity of the automatic light control system

      E107164

      Setting
      -2
      -1
      0
      +1
      +2

  1. Customizing with the multi-display (w/ Navigation System (for Radio and Display Type) or w/ Audio and Visual System (for Radio and Display Type without Intuitive Parking Assist System))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: SETUP / Vehicle.

    3. Select the setting by referring to the table below.

      Vehicle Settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Light Sensor Sensitivity
      0
      Adjusts the sensitivity of the automatic light control system.*A
      -2, -1, 0, +1 or +2
      Main Body ECU (Multiplex Network Body ECU)
      Headlight Off Time Adjust
      30 sec.
      Keeps the headlights on for a certain period of time after turning the ignition switch off and closing all doors with the low beam headlights on.
      Off, 30 sec., 60 sec. or 90 sec.
      Daytime Running Lights*1
      On
      ON/OFF of the DRL function
      On or Off

      1. *1: Headlight dimmer switch with DRL OFF function.

      HINT:
      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


      *A 
      Sensitivity of the automatic light control system

      E107164

      Setting
      -2
      -1
      0
      +1
      +2