Home › Audio/Visual/Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM

BLIND SPOT MONITOR SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave/ Data List.

  5. Read the Data List according to the display on the Techstream.

    Blind spot monitor Master 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Main Switch
    Blind spot monitor main switch (warning canceling switch assembly) / OFF or ON
    ON: Blind spot monitor main switch (warning canceling switch assembly) ON
    OFF: Blind spot monitor main switch (warning canceling switch assembly) OFF
    -
    Warning Indicator Turning on (Master)
    State of the outer rear view mirror indicator RH turning on / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      2. Vehicle detected in right hand side warning area
      3. Right turn signal: OFF
      4. Vehicle speed 40 km/h (25 mph) or more
      5. Shift lever in any position except R
      6. Blind spot monitor warning light not illuminated
    -
    Warning Indicator Flashing (Master)
    State of the outer rear view mirror indicator RH flashing / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      1. Vehicle detected in right hand side warning area
      1. Right turn signal: ON
      1. Vehicle speed 40 km/h (25 mph) or more
      1. Shift lever in any position except R
      1. Blind spot monitor warning light not illuminated
    -
    Turn Switch State
    Master side, slave side state of the turn SW / master ON, slave ON or OFF
    Master ON: Right turn switch on
    Slave ON: Left turn switch on
    OFF: Switch not operated
    -
    Reverse
    State of the shift position R signal / OFF or ON
    ON: Shift lever in R
    OFF: Shift lever in any position except R
    -
    Vehicle Speed
    Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
    Vehicle stopped: 0 km/h (0 mph)
    -
    Steering Angle
    Steering angle sensor / Min.: -3072°, Max.: 3070.5°
    Left turn: Increases
    Right turn: Decreases
    -
    Power Supply Voltage
    Power supply voltage / Min.: 0 V, Max.: 50 V
    Always: 11 to 14 V
    -
    HV Flag
    Hybrid vehicle / OFF or ON
    OFF: Non-hybrid vehicle
    ON: Hybrid vehicle
    -
    VGRS Flag
    VGRS installed / OFF or ON
    OFF: VGRS not installed
    ON: VGRS installed
    -
    Main SW Inspection Completeness Flag
    Completion of inspection for blind spot monitor main switch (warning canceling switch assembly) / Incompl or compl
    Incompl: Inspection not completed
    Compl: Inspection completed
    Changes to Compl when the blind spot monitor main switch (warning canceling switch assembly) is changed from off to on during Test Mode.
    Beam Axis Inspection Completeness Flag
    Completion of beam axis inspection / Incompl or compl
    Incompl: Inspection not completed
    Compl: Inspection completed
    Changes to Compl when Test Mode has been entered.
    Destination Undefined Flag
    Destination determination / Unfixed or Fixed
    Unfixed: Sensor destination information not determined
    Fixed: Sensor destination information determined according to CAN destination information
    -
    Number of DTC
    Number of DTC / Min.: 0, Max.: 255
    When system is normal: 0
    when a malfunction is detected: More than 0
    -

    Blind spot monitor Slave 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Warning Indicator Turning on (Slave)
    State of the outer rear view mirror indicator LH turning on / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      2. Vehicle detected in left hand side warning area
      3. Left turn signal: OFF
      4. Vehicle speed 40 km/h (25 mph) or more
      5. Shift lever in any position except R
      6. Blind spot monitor warning light not illuminated
    -
    Warning Indicator Flashing (Slave)
    State of the outer rear view mirror indicator LH flashing / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      2. Vehicle detected in left hand side warning area
      3. Vehicle speed 40 km/h (25 mph) or more
      4. Left turn signal: ON
      5. Shift lever in any position except R
      6. Blind spot monitor warning light not illuminated
    -
    Turn Switch State
    Master side, slave side state of the turn SW / master ON or slave ON or OFF
    Master ON: Right turn switch on
    Slave ON: Left turn switch on
    OFF: Switch not operated
    -
    Reverse
    State of the shift position R signal / OFF or ON
    ON: Shift lever in R
    OFF: Shift lever in any position except R
    -
    Vehicle Speed
    Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
    Vehicle stopped: 0 km/h (0 mph)
    -
    Steering Angle
    Steering angle sensor / Min.: -3072°, Max.: 3070.5°
    Left turn: Increases
    Right turn: Decreases
    -
    Power Supply Voltage
    Power supply voltage / Min.: 0 V, Max.: 50 V
    Always: 11 to 14 V
    -
    HV Flag
    Hybrid vehicle / OFF or ON
    OFF: Non-hybrid vehicle
    ON: Hybrid vehicle
    -
    VGRS Flag
    VGRS installed / OFF or ON
    OFF: VGRS not installed
    ON: VGRS installed
    -
    Beam Axis Inspection Completeness Flag
    Completion of beam axis inspection / Incompl or compl
    Incompl: Inspection not completed
    Compl: Inspection completed
    Changes to Compl when Test Mode has been entered.
    Destination Undefined Flag
    Destination determination / Unfixed or Fixed
    Unfixed: Sensor destination information not determined
    Fixed: Sensor destination information determined according to CAN destination information
    -
    Number of DTC
    Number of DTC / Min.: 0, Max.: 255
    When system is normal: 0
    when a malfunction is detected: More than 0
    -