Home › Audio/Visual/Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM

BLIND SPOT MONITOR SYSTEM > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA
  1. Whenever a DTC is detected, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.


CHECK FREEZE FRAME DATA
  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the blind spot monitor main switch (warning canceling switch assembly) on.

  4. Turn the Techstream on.

  5. Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Trouble Codes.

  6. According to the display on the Techstream, select the trouble code data display with Freeze Frame Data.

    Blind spot monitor Master 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Warning Indicator Turning on (Master)
    State of the outer rear view mirror indicator RH turning on / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      2. Vehicle detected in right hand side warning area
      3. Right turn signal: OFF
      4. Vehicle speed 40 km/h (25 mph) or more
      5. Shift lever in any position except R
      6. Blind spot monitor warning light not illuminated
    -
    Warning Indicator Flashing (Master)
    State of the outer rear view mirror indicator RH flashing / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      1. Vehicle detected in right hand side warning area
      1. Right turn signal: ON
      1. Vehicle speed 40 km/h (25 mph) or more
      1. Shift lever in any position except R
      1. Blind spot monitor warning light not illuminated
    -
    Turn Switch State
    Master side, slave side state of the turn SW / master ON, slave ON or OFF
    Master ON: Right turn switch on
    Slave ON: Left turn switch on
    OFF: Switch not operated
    -
    Reverse
    State of the shift position R signal / OFF or ON
    ON: Shift lever in R
    OFF: Shift lever in any position except R
    -
    Vehicle Speed
    Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
    Vehicle stopped: 0 km/h (0 mph)
    -
    Steering Angle
    Steering angle sensor / Min.: -3072°, Max.: 3070.5°
    Left turn: Increases
    Right turn: Decreases
    -
    Power Supply Voltage
    Power supply voltage / Min.: 0 V, Max.: 50 V
    Always: 11 to 14 V
    -

    Blind spot monitor Slave 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Warning Indicator Turning on (Slave)
    State of the outer rear view mirror indicator LH turning on / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      2. Vehicle detected in left hand side warning area
      3. Left turn signal: OFF
      4. Vehicle speed 40 km/h (25 mph) or more
      5. Shift lever in any position except R
      6. Blind spot monitor warning light not illuminated
    -
    Warning Indicator Flashing (Slave)
    State of the outer rear view mirror indicator LH flashing / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      2. Vehicle detected in left hand side warning area
      3. Vehicle speed 40 km/h (25 mph) or more
      4. Left turn signal: ON
      5. Shift lever in any position except R
      6. Blind spot monitor warning light not illuminated
    -
    Turn Switch State
    Master side, slave side state of the turn SW / master ON, slave ON or OFF
    Master ON: Right turn switch on
    Slave ON: Left turn switch on
    OFF: Switch not operated
    -
    Reverse
    State of the shift position R signal / OFF or ON
    ON: Shift lever in R
    OFF: Shift lever in any position except R
    -
    Vehicle Speed
    Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
    Vehicle stopped: 0 km/h (0 mph)
    -
    Steering Angle
    Steering angle sensor / Min.: -3072°, Max.: 3070.5°
    Left turn: Increases
    Right turn: Decreases
    -
    Power Supply Voltage
    Power supply voltage / Min.: 0 V, Max.: 50 V
    Always: 11 to 14 V
    -


CLEAR FREEZE FRAME DATA

NOTICE:
Clearing the DTCs will also clear the Freeze Frame Data

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the blind spot monitor main switch (warning canceling switch assembly) on.

  4. Turn the Techstream on.

  5. Clear the DTC and Freeze Frame Data.