Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
NM2030EQ _51 Engine / Hybrid System _014288 2GR-FE ENGINE CONTROL _0072899 SFI SYSTEM DE DETAILS F

2GR-FE ENGINE CONTROL  SFI SYSTEM  DETAILS  ACCELERATOR PEDAL SENSOR  


CONSTRUCTION


a.

This non-contact type accelerator pedal position sensor uses a Hall IC, which is mounted on the accelerator pedal arm.

i.

A magnetic yoke is mounted at the base of the accelerator pedal arm. This yoke rotates around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux that occur into electrical signals, and outputs them in the form of accelerator pedal position signals to the ECM.


ii.

The Hall IC contains 2 circuits, one for the main signal, and one for the sub signal. It converts the accelerator pedal position (angle) into electric signals that have differing characteristics and outputs them to the ECM.

W100142
1.167,1.948 1.635,0.604 1.635,0.604 1.917,0.604 true 2.229,2.583 1.938,3.313 1.938,3.313 1.604,3.313 true 4.552,1.115 4.469,0.583 4.469,0.583 4.25,0.583 true 4.438,1.583 3.698,1.333 3.698,1.333 3.5,1.333 true 4.427,2.063 3.688,2.313 3.688,2.313 3.49,2.313 true 2.052,2.052 1.49,2.906 1.49,2.906 1.323,2.906 true 4.563,2.51 4.354,2.969 4.354,2.969 4.167,2.969 true 3.333,3.292 5.542,3.615 2.208,0.323 10 false Accelerator Pedal Position Sensor 3.063,1.26 3.542,1.615 0.479,0.354 10 false Hall IC 3.76,0.5 4.302,0.896 0.542,0.396 10 false Magnet 3.031,2.229 3.51,2.583 0.479,0.354 10 false Hall IC 1.167,4.052 1.458,4.458 0.292,0.406 10 false (V) 1.49,4.302 1.615,4.635 0.125,0.333 10 false 5 0.615,5.271 1.573,5.615 0.958,0.344 10 false Output Voltage 1.5,6.01 1.625,6.302 0.125,0.292 10 false 0 0.813,6.385 1.667,6.74 0.854,0.354 10 false Fully Closed 5.167,6.365 5.917,6.698 0.75,0.333 10 false Fully Open 2.302,6.365 4.479,6.667 2.177,0.302 10 false Accelerator Pedal Position (Angle) 5.333,1.031 5.729,1.323 0.396,0.292 10 false VPA 5.344,1.375 5.74,1.667 0.396,0.292 10 false EPA 5.354,1.75 5.802,2.01 0.448,0.26 10 false VCPA 5.354,2.031 5.75,2.323 0.396,0.292 10 false VPA2 5.354,2.375 5.813,2.656 0.458,0.281 10 false EPA2 5.365,2.75 5.76,3.042 0.396,0.292 10 false VCP2 1.969,0.531 2.448,0.885 0.479,0.354 10 false Hall IC 3.667,5.417 4.063,5.708 0.396,0.292 10 false VPA 2.49,5 2.885,5.292 0.396,0.292 10 false VPA2 6.281,1.885 6.656,2.198 0.375,0.313 10 false ECM 0.188,3.219 1.625,3.521 1.438,0.302 10 false Accelerator Pedal Arm 0.375,2.813 1.406,3.177 1.031,0.365 10 false Magnetic Yoke 3.635,2.865 4.198,3.146 0.563,0.281 10 false Magnet

HINT:

The inspection method differs from a contact type accelerator pedal position sensor because a non-contact type accelerator pedal position sensor uses a Hall IC. For details, refer to the Repair Manual.