FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
| Brake Actuator Assembly | Skid Control ECU | Judges the vehicle driving condition based on the signals from each sensor and switch, and sends the brake control signals to the brake actuator. |
| Solenoid Relay (Built into Skid Control ECU) | Supplies power to the solenoid valves. | |
| Motor Relay (Built into Skid Control ECU) | Supplies power to the pump motor. | |
| Solenoid Valves | ·
The hydraulic circuit has 2 master cylinder cut solenoid valves, 2 reservoir cut solenoid valves, 4 pressure holding solenoid valves and 4 pressure reduction solenoid valves. ·
Change the fluid path based on the signals from the skid control ECU during the operation of the brake control system functions, in order to control the fluid pressure applied to the wheel cylinders. |
|
| Pump Motor | Drives the pumps inside the brake actuator. | |
| Master Cylinder Pressure Sensor | Detects the master cylinder pressure. | |
| Speed Sensors | Detect the wheel speed of each of the 4 wheels. | |
| Airbag Sensor Assembly | ·
The airbag sensor assembly incorporates the acceleration sensor and yawrate sensor. ·
The yawrate sensor detects the vehicle's yaw rate. ·
The acceleration sensor detects the vehicle's longitudinal and lateral acceleration. ·
The airbag sensor assembly sends the detection signals from the yawrate sensor and acceleration sensor to the skid control ECU via CAN communication. |
|
| Steering Sensor | Detects the steering direction and angle of the steering wheel. | |
| Stop Light Switch Assembly | Detects the brake pedal depressing signal. | |
| Brake Pedal Load Sensing Switch | Detects the brake pedal depression. | |
| Parking Brake Switch Assembly | Detects the parking brake pedal status. | |
| Main Body ECU (Multiplex Network Body ECU) | Transmits the parking brake switch signal to the skid control ECU. | |
| ECM | ·
Sends the throttle position signal, accelerator pedal position signal, engine speed signal etc., to the skid control ECU. ·
Based on the signals from the skid control ECU, controls the engine output. |
|
| Combination Meter Assembly | Brake Warning Light | ·
Illuminates to alert the driver when the skid control ECU detects a malfunction in the EBD or brake system. ·
Illuminates to alert the driver when the brake fluid level is low. ·
Illuminates to inform the driver when the parking brake is operated. |
| ABS Warning Light | Illuminates to alert the driver when the skid control ECU detects a malfunction in the ABS. | |
| Slip Indicator Light | ·
Blinks to inform the driver when the TRC or VSC is performing control. ·
Illuminates to alert the driver when the skid control ECU detects a malfunction in the TRC and/or VSC. |
|
| Master Warning Light | Illuminates to alert the driver when a message is being displayed on the multi-information display. | |
| Multi-information Display | Shows a warning message to alert the driver, such as when the vehicle is being driven with the parking brake still engaged. | |
| Buzzer | Sounds to alert the driver when the vehicle is being driven with the parking brake still engaged. | |
SYSTEM CONTROL
Table of System Control
The brake control system has the following system/functions:
| Control | Outline |
|---|---|
| Anti-lock Brake System (ABS) | Helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface. |
| Electronic Brake Force Distribution (EBD) | EBD control utilizes ABS, realizing proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, it also controls the brake forces of the right and left wheels, helping maintain vehicle behavior. |
| Brake Assist | The primary purpose of Brake Assist is to provide supplementary brake force to assist a driver who cannot generate a large brake force during emergency braking, thus helping ensure the vehicle's braking performance. |
| Traction Control (TRC) | Helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface. |
| Vehicle Stability Control (VSC) | Helps restrain sideways slippage of the vehicle during a strong understeer tendency or strong oversteer tendency while cornering. |
Anti-lock Brake System (ABS)
The ABS helps prevent the wheels from locking during sudden braking or braking on a slippery surface. This helps provide the appropriate braking force for the road surface conditions, thus ensuring vehicle stability and excellent braking performance.
| *A | With ABS | *B | Without ABS |
| *a | Brake Operation | - | - |
Electronic Brake Force Distribution (EBD)
This function controls the brake force that acts on the rear wheels in accordance with the changes in the vehicle conditions such as load factors or deceleration, in order to ensure excellent braking performance.
During braking while cornering, this function controls the brake force that acts on the left and right wheels in accordance with the vehicle conditions at that time. This ensures vehicle stability and excellent braking performance.
|
Brake Force |
|
Control Moment |
Brake Assist
With brake assist, based on the signals from the master cylinder pressure sensor, the skid control ECU calculates the speed with which and the amount the brake pedal is applied to determine if the driver is attempting emergency braking. If the skid control ECU determines that the driver is attempting emergency braking, the brake assist function activates the brake actuator to increase the brake fluid pressure, which increases the brake force.
Traction Control (TRC)
TRC helps prevent the drive wheels from slipping if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface. Together with hydraulic control of the drive wheels, the skid control ECU requests the ECM to perform engine output control. This produces drive force suited to the driving conditions in order to ensure proper start-off acceleration.
| *A | Without TRC | *B | With TRC |
| *1 | Engine | *2 | ECM |
| *3 | Brake Actuator Assembly
- Skid Control ECU |
- | - |
| *a | Excessive drive force causes the drive wheels to slip | *b | Regulation of the throttle to control engine output |
|
Slippery Surface | - | - |
Vehicle Stability Control (VSC)
The following 2 examples can be considered as circumstances in which the tires exceed their lateral grip limit. VSC is designed to help control the vehicle behavior by controlling the engine output and the brakes at each wheel when the vehicle is subject to one of the conditions indicated below.
| *a | Understeer Tendency | *b | Oversteer Tendency |
To determine the condition of the vehicle, sensors detect the steering angle, vehicle speed, vehicle's yaw rate, and the vehicle's lateral acceleration, which are then calculated by the skid control ECU.
Whether or not the vehicle is experiencing understeer is determined by the difference between the target yaw rate and the vehicle's actual yaw rate. When the vehicle's actual yaw rate is smaller than the target yaw rate (a target yaw rate is determined based on the vehicle speed and steering angle) that should be generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the target locus of travel. Thus, the skid control ECU determines that there is a large understeer tendency.
| *a | Actual Locus of Travel (Actual Yaw Rate) | *b | Locus of Travel Based on the Target Yaw Rate |
Whether or not the vehicle is experiencing oversteer is determined by the values of the vehicle's slip angle and the vehicle's slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle is large, and the slip angular velocity is also large, the skid control ECU determines that the vehicle has a large oversteer tendency.
| *a | Slip Angle | *b | Direction of Travel of the Vehicle's Center of Gravity |
| *c | Movement of Vehicle | - | - |
When the skid control ECU determines that the vehicle exhibits a tendency to experience either understeer or oversteer, it decreases the engine output and applies the brakes of the front or rear wheels to control the vehicle's yaw moment. The basic operation of the VSC functions is described below. However, the control method differs depending on the vehicle's characteristics and driving conditions.
When the skid control ECU determines that there is a large understeer tendency, it takes countermeasures in accordance with the extent of that tendency. The skid control ECU controls the engine output and applies the brake of the front wheel and rear wheel of the inner circle of the turn in order to help restrain the understeer tendency.
| *a | Control Moment | *b | Braking Force |
When the skid control ECU determines that there is a large oversteer tendency, it takes countermeasures in accordance with the extent of that tendency. It applies the brakes of the front wheel and rear wheel of the outer circle of the turn, and generates an outward moment of inertia in the vehicle, in order to restrain the oversteer tendency. Along with the reduction in the vehicle speed caused by the braking force, excellent vehicle stability is ensured.
| *a | Control Moment | *b | Braking Force |
FAIL-SAFE
If a failure occurs in the skid control ECU, sensors, or brake actuator assembly, the system continues performing brake control by excluding the failed area and using only the areas that are operating normally.
DIAGNOSIS
If the skid control ECU detects a malfunction in the brake control system, the warning lights or indicator light illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.
This system has a sensor signal check (test mode) function.
For details of DTCs and the check function, refer to the Repair Manual.