Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.02–2015.04
NM2030EQ _58 Vehicle Interior _014317 METER / GAUGE / DISPLAY _0072938 METER / GAUGE SYSTEM DE DETAILS F

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  DETAILS  COMBINATION METER  


FUNCTION


a.

Combination Meter Assembly

i.

Buzzer Function

1.

The table below shows the warning and reminder functions of the buzzer in the combination meter assembly.

*1: Models for G.C.C. countries

*2: Models for Australia

*3: Models with smart entry and start system

*4: Models with sliding roof system

1 Driver Seat Belt Warning (5 Times at the Maximum)*1 2 Driver Seat Belt Warning (Once)*1
3 Front Passenger Seat Belt Warning (Once)*1 4 Seat Belt Warning (Level 2)
5 Seat Belt Warning (Level 1) 6 Rear Passenger Seat Belt Warning*2
7 EPS Warning 8 Smart Entry and Start System Warning 1 (Continuous)*3
9 Smart Entry and Start System Warning 2 (Intermittent)*3 10 Key Reminder Indicating Buzzer
11 Smart Entry and Start System Warning 2 (Continuous, 9 times at the maximum)*3 12 Smart Entry and Start System Warning (Once)*3
13 Multi-information Display Warning 14 Immobiliser Certification Reminder
15 Speed Warning*1 16 Parking Brake Engaged Warning
17 Door Open while Driving Warning 18 S Mode Operation Reject Warning
19 Sliding Roof Open Warning*4 20 Turn Signal/Hazard Warning Operation




b.

LCD

i.

Display Flow Function

1.

The fuel gauge side LCD display changes in the following order due to ODO/TRIP switch operation.

Y113360
0.473,0.552 0.783,0.843 0.310,0.291 10 *1 2.96,0.552 3.269,0.843 0.310,0.291 10 *2 5.425,0.552 5.735,0.843 0.310,0.291 10 *3
*1 Odometer *2 Trip Meter A
*3 Trip Meter B - -
V100136

ODO/TRIP switch pressed briefly. - -





c.

Multi-information Display

i.

Display Flow Function

1.

The multi-information display flow can be switched as shown in the flow chart below:

Y111604
4.115,0.885 4.615,1.292 0.5,0.406 10 false OFF 1.354,1.594 2.469,2 1.115,0.406 10 false Cyclic Display*2 2.115,1.302 2.333,1.542 0.219,0.24 10 false *1 2.427,4.552 2.646,4.792 0.219,0.24 10 false *4 0.781,5.385 1,5.625 0.219,0.24 10 false *5 1.427,0.719 2.396,1.125 0.969,0.406 10 false New Message 1.177,3.188 1.927,3.594 0.75,0.406 10 false Opening*3 5.625,4.344 6.51,4.75 0.885,0.406 10 false DTC Display 3.365,5.698 4.5,6.104 1.135,0.406 10 false New Message 0.844,5.708 1.938,6.115 1.094,0.406 10 false Cyclic Display*1 0.531,6.688 1.885,7 1.354,0.313 10 false : Conditions met 0.531,7.177 1.906,7.49 1.375,0.313 10 false : Conditions not met 2.24,7.177 3.667,7.49 1.427,0.313 10 false : DISP switch operated 2.24,6.688 3.656,6.979 1.417,0.292 10 false : Setting completed 3.104,4.354 4.198,4.76 1.094,0.406 10 false Advisory Display 0.938,4.365 2.083,4.792 1.146,0.427 10 false Cruise Information Display 3.74,1.625 4.958,2.042 1.219,0.417 10 false Farewell Message 0.229,2.51 1.458,2.833 1.229,0.323 10 false Ignition Switch ON 5.719,0.99 6.583,1.708 0.865,0.719 10 false Door Unlock Mode Display 4.365,2.5 5.771,2.823 1.406,0.323 10 false Ignition Switch OFF

No. Transition Condition
*1 Conditions are not met and all new messages have been displayed.
*2 If the display conditions for 2 or more messages are met, relevant messages are alternately displayed for 2 seconds each.
*3 If the ignition switch is turned off during the "Opening" display, the "Opening" display will be shown from the beginning.
*4 If the DISP switch is used to change from an advisory message to the cruise information display screen, repeatedly operating the DISP switch will cycle through the cruise information screens and then return the advisory message if the display conditions are still met.
*5 If the DISP switch is not operated for more than 6 seconds with any of the caution or warning message display conditions still met, the relevant caution or warning messages are displayed.



ii.

Cruise Information Mode Function

1.

The cruise information is displayed in the following order each time the DISP switch of the steering pad switch assembly is pressed.

Y114036
1.875,3.625 1.875,4.229 true 1.802,4.271 2.125,4.552 0.323,0.281 10 false *1 3.26,0.135 3.5,0.375 0.24,0.24 10 false (1) 3.26,1.781 3.5,2.021 0.24,0.24 10 false (2) 3.26,3.448 3.5,3.688 0.24,0.24 10 false (3) 5.604,2.771 5.844,3.01 0.24,0.24 10 false (4) 5.563,0.76 5.802,1 0.24,0.24 10 false (5)
*1 DISP Switch - -
V100136

DISP switch pressed briefly. - -


2.

The cruise information mode items displayed are as follows:

No. Information Outline
(1) Cruising Range
·

Displays a value that has been calculated by the combination meter assembly. When the ignition switch is turned to ON, the combination meter assembly calculates the range based on continuously monitoring and storing information on fuel consumption data, and the residual fuel volume.

·

This display is updated every 10 seconds.


Average Fuel Consumption
·

Displays a value that has been calculated by the combination meter assembly based on the distance driven and the fuel consumption volume (fuel injection signal from the ECM).

·

This display is updated every 10 seconds.


(2) Average Speed
·

Displays the average vehicle speed calculated by the combination meter assembly based on the engine start signal and vehicle speed signal.

·

This display is updated every 10 seconds.


Elapsed Time Displays the length of time since the engine was started.
(3) Eco Drive Level Display
·

Displays the average fuel consumption calculated since the engine was started. Uses 4 different height bars to display the level.

·

This display is updated every 10 seconds.


(4) Settings Customizes the combination meter assembly language display and Eco Driving Indicator Light and instantaneous fuel consumption gauge deactivated or activated display states.
(5) Blank Screen -



iii.

Eco Drive Level

1.

The eco drive level changes among 4 levels to indicate the average fuel consumption.

2.

After the ignition switch is turned off, the eco drive level display appears for 3 seconds in the multi-information display. When the average fuel consumption is 8.8 L/100 km or less the "EXCELLENT!" message flashes.

Average Fuel Consumption Level (L/100km) Multi-information Display
Level 0 (15 or more)
Y130224

Level 1 (13 to 15)
Y130225

Level 2 (11 to 13)
Y130226

Level 3 (9 to 11)
Y130227

Level 4 (9 or less) When driving
Y130228

After ignition switch is turned off
Y130229




iv.

Customization Function

1.

In the settings screen of cruise information mode, pressing and holding the DISP switch enters setting mode.

2.

Press the DISP switch briefly to select the item to be customized. Press and hold the DISP switch to confirm the selection.

Y111611
4.365,0.344 4.688,0.625 0.323,0.281 10 false *a 4.375,1.802 4.698,2.083 0.323,0.281 10 false *b
*a Language Setting *b Eco Driving Indicator Light ON/OFF Setting
V100136

DISP switch pressed briefly.
V100135

DISP switch pressed and held.
V100137

If the vehicle has reached a speed of 8 km/h (5 mph) - -


3.

In setting mode, the following items of the combination meter assembly can be customized.

Item Available Setting
Language
·

English

·

French

·

Spanish


Eco Driving Indicator Light and Instantaneous Fuel Consumption Gauge
·

On

·

Off





v.

Warning Mode Function

1.

When a warning is necessary, the warning display interrupts the display in the multi-information display.

2.

The master warning light may illuminate or blink and the buzzer in the combination meter assembly may sound depending on the item in the multi-information display.

Priority Indication/Warning Master Warning Light Buzzer

*1: If the vehicle has reached a speed of 5 km/h (3 mph).

*2: Models with TOYOTA parking assist-sensor system

*3: Models with smart entry and start system

*4: Models with blind spot monitor system

*5: Models with sliding roof system

1 Door Open (While Driving)*1 Blinks Sounds
Door Open - -
Clearance Sonar Obstruction Detection*2 - -
CHECK SONAR SYSTEM*2 Illuminates Sounds
CLEAN SONAR*2 Illuminates Sounds
2 AUTO POWER OFF TO CONSERVE BATTERY - -
3 SHIFT TO P POSITION*3 Blinks Sounds
4 RELEASE PARKING BRAKE Blinks Sounds
KEY NOT DETECTED*3 Blinks Sounds
5 CHECK ENTRY & START SYSTEM*3 Blinks Sounds
6 CHECK CRUISE CONTROL SYSTEM Illuminates Sounds
BSM NOT AVAILABLE*4 Illuminates Sounds
CHECK BSM SYSTEM*4 Illuminates Sounds
7 TURN POWER OFF*3 Blinks Sounds
KEY DETECTED IN VEHICLE*3 Blinks Sounds
MOONROOF OPEN*5 Blinks Sounds
DEPRESS BRAKE PEDAL, TOUCH ENGINE SWITCH TO START*3 Blinks Sounds
DEPRESS BRAKE PEDAL AND PUSH ENGINE SWITCH TO START*3 Blinks Sounds
SHIFT TO P POSITION TO START*3 Blinks Sounds
8 STEERING LOCK ACTIVE Blinks Sounds
9 KEY BATTERY LOW*3 Illuminates Sounds
10 POWER ON*3 - -
Engine start ready state*3 - -





SYSTEM CONTROL


a.

Eco Driving Indicator Light Operation

·

The ignition switch is ON and the engine is running.

·

The vehicle is being driven with the shift lever in D.

·

Temporary S mode is not selected (The shift paddle switch (transmission shift switch assembly) is not operated).

·

The vehicle is at a speed of 130 km/h (81 mph) or below.