Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
NM2030EQ _59 Vehicle Exterior _014323 SLIDING ROOF / CONVERTIBLE _0072946 SLIDING ROOF SYSTEM CO CONTROL F

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  CONTROL  SLIDING ROOF CONTROL  


SYSTEM CONTROL


a.

The sliding roof system has the following functions:

Function Outline Customizable*1

*1: The customizable functions can be turned on or off using the customized body electronics system. For details, refer to the Repair Manual.

*2: If the sliding roof ECU has not been initialized, this function does not operate.

*3: Except models for G.C.C. countries

*4: Default setting is on.

*5: Default setting is off.

Manual Slide Open-and-close This function opens or closes the sliding roof while the open switch or close switch is pressed for 0.3 seconds or less. The sliding roof stops as soon as the switch is released. Standard (Not Customizable)
One-touch Slide Auto Open*2
·

This function opens the sliding roof up to the comfort stop position when the open switch is pressed for 0.3 seconds or more.

·

To suppress wind noise, this function stops opening the roof at the comfort stop position. By pressing the open switch once again, the sliding roof can be fully opened.


*4
One-touch Slide Auto Close*2 This function fully closes the sliding roof when the close switch is pressed for 0.3 seconds or more. *4
Manual Tilt Up-and-down This function tilts up or down the sliding roof while the up switch or down switch is pressed for 0.3 seconds or less. The sliding roof stops as soon as the switch is released. Standard (Not Customizable)
One-touch Auto Tilt Up-and-down*2 This function fully tilts up or down the sliding roof when the up switch or down switch is pressed for 0.3 seconds or more. *4
Jam Protection*2 The jam protection function automatically stops the sliding roof and moves it open half way (or to the fully tilted up position) if a foreign object gets jammed in the sliding roof during close or tilt down operation. Standard (Not Customizable)
Key-off Operation*2 The key-off operation function makes it possible to operate the sliding roof for approximately 45 seconds after the ignition switch is turned to ACC or off, if the front doors are not opened. Standard (Not Customizable)
Key-linked Operation Setting*2 The key-linked operation for the sliding roof can be switched between slide operation and tilt operation. Default setting is slide operation
Key-linked Open-and-close*2,*3
·

When the key cylinder in the driver door is turned and held in the unlock position for 2.5 seconds or more, the sliding roof drive gear sub-assembly activates the sliding roof motor to open the sliding roof while the key cylinder is turned.

·

Similarly, turning and holding the driver door key cylinder in the lock position will cause the sliding roof to close.


*5
Key-linked Tilt up-and-down*2,*3
·

When the key cylinder in the driver door is turned and held in the unlock position for 2.5 seconds or more, the sliding roof drive gear sub-assembly activates the sliding roof motor to tilt up the sliding roof while the key cylinder is turned.

·

Similarly, turning and holding the driver door key cylinder in the lock position will cause the sliding roof to tilt down.


*5
Transmitter-linked Operation Setting The transmitter-linked operation for the sliding roof can be switched between slide operation and tilt operation. Default setting is slide operation
Transmitter-linked Open*2,*3 When the main body ECU (multiplex network body ECU) receives an unlock signal from the transmitter continuously for 4.0 seconds or more via the door control receiver, the sliding roof drive gear sub-assembly opens the sliding roof. *5
Transmitter-linked Tilt Up*2,*3 When the main body ECU (multiplex network body ECU) receives an unlock signal from the transmitter continuously for 4.0 seconds or more via the door control receiver, the sliding roof drive gear sub-assembly tilts up the sliding roof. *5
Sliding Roof Open Warning*2 When the ignition switch is turned from ON to off and the driver door is opened with the sliding roof open, the buzzer in the combination meter assembly sounds once. Then, a warning message appears on the multi-information display and the master warning light blinks. *4

HINT:
·

The sliding roof ECU in the sliding roof drive gear sub-assembly memorizes the initial position of the sliding roof. This memory is not cleared if the battery terminals are disconnected. However, initialization is necessary after the sliding roof drive gear sub-assembly is replaced.

·

After replacing the sliding roof drive gear sub-assembly, the sliding roof will not operate correctly. In this case, the sliding roof position must be initialized as described below:

·

Keep pressing the sliding roof switch (tilt-up or slide close) until initialization completes. This will enable the sliding roof ECU to start initializing and perform the tilt up, tilt down, open and close operations of the sliding roof in sequence.

·

Keep the switch pressed for 1 second after the tilt up operation is completed.

·

The sliding roof ECU performs the tilt down, open and close operations.

·

The initialization process ends when the close operation is completed.


·

Keep the tilt-up or slide close switch pressed during initialization. If the tilt up or close switch is released during initialization, the system will not be able to complete initialization. If this occurs, the aforementioned steps must be performed again.

·

For details, refer to the Repair Manual.




b.

Jam Protection Function

i.

To control the jam protection function, the sliding roof ECU monitors the amount of movement and judges jamming of the sliding roof based on the pulse signals from Hall IC1, and the movement direction of the sliding roof from the phase difference between the pulses from Hall IC1 and Hall IC2.

Y100150
0.313,0.146 3.51,0.417 3.198,0.271 12 Judgment of Movement and Jamming: 1.125,1.26 1.667,1.719 0.542,0.458 10 Hall IC1 Signal 1.052,2.438 2.76,2.76 1.708,0.323 10 Time for 1 Motor Revolution 1.604,2.771 2.802,3.073 1.198,0.302 10 Normal 4.417,2.5 6.198,2.771 1.781,0.271 10 Time for 1 Motor Revolution 4.958,2.781 5.698,3.115 0.74,0.333 10 Jammed 0.313,3.198 3.396,3.552 3.083,0.354 12 Judgment of Movement Direction: 1.083,4.24 1.615,4.667 0.531,0.427 10 Hall IC1 Signal 1.063,5.052 1.677,5.646 0.615,0.594 10 Hall IC2 Signal 1.635,5.781 3.135,6.354 1.5,0.573 10 OPEN/TILT DOWN 4.708,5.833 5.823,6.344 1.115,0.51 10 CLOSE/TILT UP