Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › 2012.02–2015.04
NM2030EQ _56 Audio / Visual / Telematics _014312 PARK ASSIST / MONITORING _0072925 TOYOTA PARKING ASSIST-SENSOR SYSTEM CO CONTROL F

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  CONTROL  TOYOTA PARKING ASSIST-SENSOR CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
No. 1 Ultrasonic Sensor (4) Detects the distance between the vehicle and an obstacle.
No. 1 Clearance Warning Buzzer Sounds to inform the driver according to the distance to the obstacle.
Combination Meter Assembly
·

Multi-information Display


·

Displays the location of the obstacle and the approximate distance between the vehicle and the obstacle.

·

Displays an indication of malfunction or freezing of an No. 1 ultrasonic sensor to inform the driver.


Back Sonar or Clearance Sonar Switch Assembly Operating this switch allows the operation of TOYOTA parking assist-sensor system to be enabled or disabled.
Clearance Warning ECU Assembly
·

Judges the approximate distance between the vehicle and an obstacle based on signals from the No. 1 ultrasonic sensors. Output signals are sent to the multi-information display.

·

Sounds the No. 1 clearance warning buzzer.


Air Conditioning Amplifier Assembly Sends outside temperature information to the clearance warning ECU assembly to adjust the distance rate from the No. 1 ultrasonic sensors.
Main Body ECU (Multiplex Network Body ECU) Sends model destination (information to indicate the market the vehicle was built for - such as Canada) to the clearance warning ECU assembly.
ECM Transmits the shift position signals to the clearance warning ECU assembly.
Park/Neutral Position Switch Assembly Sends the shift position signals to the ECM.


SYSTEM CONTROL


a.

Detection Area

i.

The detection areas of the No. 1 ultrasonic sensor are as shown in the following illustration.


ii.

These detection areas are applicable when positioning a 60 mm (2.36 in.) diameter pole parallel or perpendicular to the ground. The ranges vary depending on the measuring method and type of obstacle.

Y111416C01
0.99,0.49 1.198,0.708 0.208,0.219 10 false *a 5.927,0.698 6.156,1.031 0.229,0.333 10 false *b 2.021,2.76 2.271,3 0.25,0.24 10 false *c 5.021,2.76 5.271,3 0.25,0.24 10 false *d 1.125,3.771 1.406,4.063 0.281,0.292 10 false *e 5.156,4.479 5.458,4.698 0.302,0.219 10 false *g 1.719,4.49 1.979,4.771 0.26,0.281 10 false *g 5.865,3.771 6.135,4.094 0.271,0.323 10 false *f
*a Approximately 700 mm (27.6 in.) *b Approximately 750 mm (29.5 in.)
*c Approximately 500 mm (19.7 in.) *d Approximately 600 mm (23.6 in.)
*e Approximately 400 mm (15.7 in.) *f Approximately 400 mm (15.7 in.)
*g Approximately 200 mm (7.9 in.) - -




b.

The operating condition of each sensor differs according to its installed position as shown in the table below:

Installation Position Operating Condition
Front Corner
·

Ignition switch is ON.

·

System is activated.

·

Shift lever is in a position other than P.

·

Vehicle speed is approximately 10 km/h (6 mph) or less.


Rear Corner
·

Ignition switch is ON.

·

System is activated.

·

Shift lever is in R.






DIAGNOSIS


a.

If a system malfunction is detected, the clearance warning ECU assembly stores Diagnostic Trouble Codes (DTCs) in its memory. For details, refer to the Repair Manual.