FUNCTION OF MAIN COMPONENTS
The main components have the following functions:
| Component | Function | |
|---|---|---|
|
*1: Models with SRS driver side knee airbag *2: Models for G.C.C. countries |
||
| Airbag Sensor Assembly | ·
The airbag sensor assembly receives signals from one of the front airbag sensors via its judgment circuit and from the safing sensor built into the airbag sensor assembly. After receiving these signals, it determines whether the driver side airbag, front passenger side airbag, driver side knee airbag*1, and front seat belt pretensioners should be activated. It also diagnoses system malfunctions. ·
The airbag sensor assembly receives signals from either the side airbag sensor assembly or side No. 2 airbag sensor assembly via its judgment circuit and from the safing sensor built into the airbag sensor assembly. After receiving these signals, it determines whether the front seat airbag assembly, curtain shield airbag assembly and front seat belt pretensioner*2 should be activated. It also diagnoses system malfunctions. ·
The airbag sensor assembly sends an airbag deployment signal to the ECM through the Controller Area Network (CAN) to operate fuel pump control. |
|
| Horn Button Assembly | Driver Side Squib | The airbags are used as supplements to the seat belts to help reduce impact to the occupants. |
| Instrument Panel Passenger Airbag without Door Assembly | Front Passenger Side Squib | |
| Lower No. 1 Instrument Panel Airbag Assembly*1 | Driver Side Knee Airbag Squib | |
| Front Seat Airbag Assembly LH/RH | Front Side Airbag Squib LH/RH | |
| Curtain Shield Airbag Assembly LH/RH | Curtain Shield Squib LH/RH | |
| Front Airbag Sensor LH/RH | Based on the deceleration of the vehicle during a frontal collision, a distortion is created in the sensor and converted into an electrical signal. | |
| Side Airbag Sensor Assembly LH/RH | Based on the deceleration of the vehicle during a side or rear side collision, a distortion is created in the sensor and converted into an electrical signal. | |
| Side No. 2 Airbag Sensor assembly LH/RH | ||
| Front Seat Outer Belt Assembly LH/RH | Front Pretensioner Squib LH/RH | The front seat outer belt assemblies are used to help reduce impact to the occupants. |
| ECM | The fuel pump is stopped when an SRS airbag is deployed in a frontal, side, or rear side collision. | |
| Combination Meter Assembly | SRS Warning Light | The SRS warning light turns on to alert the driver when the airbag sensor assembly detects a malfunction in the airbag system. |
SYSTEM CONTROL
Airbag for Frontal Collision
There are 3 airbags which deploy in the event of a frontal collision: the horn button assembly, instrument panel passenger airbag without door assembly, lower No. 1 instrument panel airbag assembly*.
*: Models with SRS driver side knee airbag
Deceleration sensors used for the airbag system are installed on various parts on the vehicle and calculate the deceleration (or acceleration) rate of each part during a collision.
Depending on the situation, the airbag sensor assembly sends a deployment signal to each airbag based on the information from each sensor.
Frontal collision signals are produced based on the information from the airbag sensor assembly and front airbag sensors. Frontal collision signals are used to deploy the airbags except the front seat airbag assemblies.
Airbag for Side/Rear Side Collision
There are 2 airbags which deploy in the event of a severe side collision: the front seat airbag assembly and curtain shield airbag assembly. These airbags deploy simultaneously.
For a side collision, if the side airbag sensor assembly detects an impact, it informs the airbag sensor assembly, and the airbag sensor assembly causes the front seat airbag assembly and curtain shield airbag assembly to deploy simultaneously.
For a rear side collision, if the side No. 2 airbag sensor assembly detects an impact, it informs the airbag sensor assembly via the side airbag sensor assembly, and the airbag sensor assembly causes the curtain shield airbag assembly to be deployed.
The front seat airbag assemblies are deployed and the front seat outer belt assemblies* are activated based on signals from the side airbag sensor assemblies and airbag sensor assembly.
*: Models for G.C.C. countries
The curtain shield airbag assemblies are deployed based on signals from the side No. 2 airbag sensor assemblies or the side airbag sensor assemblies and the airbag sensor assembly.
Primary Check Illumination Control
After the ignition switch is turned to ON, the airbag sensor assembly illuminates the SRS warning light in the combination meter assembly for approximately 6 seconds and conducts the primary check. During the primary check, the ignition of airbags is prohibited and a diagnosis of the airbag sensor assembly is performed. If trouble is detected during the primary check, the SRS warning light remains on even after the 6 seconds have elapsed.
DIAGNOSIS
If the airbag sensor assembly detects a malfunction in the SRS airbag system, the airbag sensor assembly stores the malfunction data in memory, in addition to illuminating the SRS warning light.
The airbag sensor assembly outputs the malfunction data and 5-digit Diagnostic Trouble Codes (DTCs) to the intelligent tester.
The 5-digit DTCs can be read after connecting the intelligent tester to the DLC3. For details, refer to the Repair Manual.
If the SRS airbags deploy, the airbag sensor assembly will turn on the SRS warning light. However, different from the ordinary diagnosis function, a DTC will not be stored. The SRS warning light cannot be turned off. It is necessary to replace the airbag sensor assembly with a new one.