SYSTEM CONTROL
The power window control system has the following functions:
| Function | Outline | Customizable*1 |
|---|---|---|
|
*1: Customizable settings can be turned on or off. For details, refer to the Repair Manual. *2: RHD Models *3: Default setting is off. |
||
| Manual Up-and-Down | For driver door:
Function that causes the window to go up while the power window regulator master switch assembly is being pulled halfway up and to go down while pushed halfway down. The window stops as soon as the switch is released. For passenger door: Function that causes the window to go up while the power window regulator switch assembly is being pulled up and to go down while pushed down. The window stops as soon as the switch is released. |
Standard (Not Customizable) |
| Driver Door Auto Up-and-Down Function | Function that enables the driver door window to be fully opened or closed by one full pull or push of the power window regulator master switch assembly. | Standard (Not Customizable) |
| Jam Protection (Driver Door) | The jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the window during one-touch auto-up operation or power up operation. | Standard (Not Customizable) |
| Remote Control (All Doors) | The power window regulator master switch assembly can control the up-and-down operation of the windows. | Standard (Not Customizable) |
| Window Lock | Operation of the 3 passenger windows is disabled when the window lock switch is pressed. | Standard (Not Customizable) |
| Key Off Operation | ·
This function makes it possible to operate the power windows for approximately 43 seconds after the engine switch is turned off (Lock), if both front doors are not opened. ·
If the window lock switch is off, the windows can be operated using any of the power window regulator switch assemblies. If the window lock switch is on, the windows cannot be operated. ·
If the driver door or front passenger door is opened during automatic window operation while the key-off operation function is on, the window will stop operating. |
Standard (Not Customizable) |
| Key-linked Up-and-Down*2 | When the electrical key transmitter sub-assembly is not in the interior detection area, the driver door is locked, and mechanical key in the driver door is turned and maintained in the lock position for 1.5 seconds or more, the main body ECU (multiplex network body ECU) activates the power window motors to raise all door windows while the mechanical key is turned.
Similarly, when the driver door is unlocked, turning and maintaining the driver door key cylinder in the unlock direction for 1.5 seconds or more will cause all door windows to be lowered. |
*3 |
| Transmitter-linked Down*2 | When the certification ECU (smart key ECU assembly) receives an unlock signal from the electrical key transmitter sub-assembly for longer than 2.4 seconds, the main body ECU (multiplex network body ECU) controls the power window motors in accordance with the signal to open the windows. | *3 |
The ECU built into each power window regulator motor stores the initial position of its door window glass. The initial position is not cleared even if battery terminals, fuses or the power window motor connector is disconnected. However, after removing or reinstalling window components, or replacing the power window regulator sub-assembly or power window regulator motor, the stored initial position data must be cleared and/or initialization must be performed. For details, refer to the Repair Manual.
Jam Protection Function
The jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the door window glass during one-touch auto up operation or power up operation.
The operation of the jam protection function is as described below.
| Door Window Glass Position from Full Close | Operation |
|---|---|
| 200 mm (7.87 in.) or more | Down operation until door window glass downward movement of 125 mm (4.93 in.) is reached, or 2.5 seconds elapse |
| 200 mm (7.87 in.) or less | Down operation until door window glass downward movement of 200 mm (7.87 in.) is reached, or 5 seconds elapse. |
The magnet and Hall IC in the power window motor are used to enable power window jam protection.
| *1 | Hall IC | *2 | Worm Gear |
| *3 | Magnet | - | - |
The Hall IC converts the changes in magnetic flux that occur through the rotation of the magnet into pulse signals and outputs them to the ECU built-into the power window motor.
To control the jam protection function, the ECU determines the amount of movement and jamming of the door window glass based on the pulse signal A from the Hall IC and judges the direction of the window glass movement based on the phase difference between the pulses of Hall IC signals A and B.
FAIL-SAFE
If the Hall IC in the power window motor (driver) malfunctions, some power window functions will be prohibited for fail-safe mode.
The power window operates when the power window switch is fully pushed down or pulled up and held in that position.
DIAGNOSIS
If a power window ECU detects a malfunction in the power window control system, a Diagnostic Trouble Code (DTC) is stored in memory.
The DTCs can be read using the Global TechStream (GTS). For details, refer to the Repair Manual.