Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2012.02–2015.04
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM J

2GR-FE ENGINE CONTROL  SFI SYSTEM  Brake Override System  


DESCRIPTION

When the vehicle is being driven, depressing the accelerator pedal sensor assembly and brake pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.

A232420E63
2.115,2.552 3.042,3.125 0.927,0.573 10 false Vehicle Speed 0.49,2.771 1.844,3.052 1.354,0.281 10 false Wheel Speed Sensor 0.458,2.406 1.865,2.656 1.406,0.25 10 false Vehicle Speed Sensor 0.458,1.667 1.625,1.99 1.167,0.323 10 false Stop Light Switch 0.448,0.688 1.615,1.313 1.167,0.625 10 false Accelerator Pedal Sensor Assembly 1.094,2.583 1.24,2.813 0.146,0.229 10 false or 3.646,0.875 3.99,1.125 0.344,0.25 10 false ECM 5,1.219 7.031,1.885 2.031,0.667 10 false Effective Accelerator Pedal Angle for System Control 2.167,1.823 2.74,2.125 0.573,0.302 10 false ON/OFF 1.875,0.865 3.052,1.438 1.177,0.573 10 false Actual Accelerator Pedal Angle 0.104,0.052 1.656,0.333 1.552,0.281 10 false Brake Override System:

Activation Conditions:
·

Vehicle is running at or above the specified speed.

·

When the accelerator pedal and brake pedal are depressed.


NOTICE:

The vehicle may not enter the brake override system control due to the relation of the accelerator pedal angle and the vehicle's speed.



Items Controlled:
·

Driving torque is restricted.


HINT:

During brake override system control, the value for the accelerator pedal angle (which is used for engine control) is forcibly reduced to a specified value. For this reason, the Data List value for Accelerator Position will be replaced with a specified value regardless of the actual accelerator pedal angle (Accel Sens. No. 1 Volt %, Accel Sens. No. 2 Volt %)



Deactivation Conditions:
·

When the brake pedal or the accelerator pedal returns to some degree.



CAUTION / NOTICE / HINT

Inspection Method

Example:

Drive at 10 km/h (6.25 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if the engine speed decreases to 1000 rpm when the brake pedal is depressed, then the brake override system has been activated.


CAUTION:

When carrying out the inspection, use a place where you are able to carry it out safely and also pay close attention to your surroundings.

Also, when driving make absolutely sure that all road traffic laws, such as speed limits, are observed.


HINT:
·

Under normal conditions, the Accelerator Position value changes in response to the Accel Sens. No. 1 Volt % value. For more information on the numerical values, refer to the Data List (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).

·

If the Data List values of Accelerator Position and Accel Sens. No. 1 Volt % do not match, and the value of Accelerator Position changes but the value of Accel Sens. No. 1 Volt % is constant, this confirms that brake override system has activated. (Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.)



NOTICE:

The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing loss of torque after the accelerator and brake pedals have both been intentionally depressed, explain to the customer that this is not a malfunction, and that the customer should avoid depressing both the accelerator and brake pedals at the same time.

Example: While operating the accelerator pedal, the customer uses their left foot to operate the brake pedal.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: System Select / Utility / All Codes.


d.

Check the DTCs.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTC is not output A
DTC is output B



A

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH AND ST1)

B

GO TO DTC CHART

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH AND ST1)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data / Stop Light Switch and ST1.

Powertrain > Engine > Data List
Tester Display
ST1
Stop Light Switch
50003 234 294,117

d.

Check the Data List indication when the brake pedal is depressed and released.

OK:
Tester Display Condition Specified Condition
Stop Light Switch Brake pedal released OFF
Brake pedal depressed ON
ST1 Brake pedal released OFF
Brake pedal depressed ON



Result:
Proceed to
OK
NG



OK

3.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY

NG

INSPECT STOP LIGHT SWITCH ASSEMBLY

3.INSPECT BRAKE PEDAL SUPPORT ASSEMBLY
a.

Inspect and adjust the brake pedal support assembly.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for RHD)>ADJUSTMENT

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


HINT:

If the stop light switch turns ON too late, the start of brake override system control may be delayed; if it turns ON too soon, brake override system control may begin too early, so conduct inspection of the brake pedal support assembly and stop light switch assembly.




A

4.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION SENSOR)

B

REPAIR OR REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

C

REPAIR OR REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

4.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data / Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %.

Powertrain > Engine > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 234 15,16

d.

Read the value displayed on the tester.

OK:
Tester Display Condition Specified Condition
Accel Sens. No. 1 Volt % Accelerator Pedal Released → Depressed → Released Values smoothly change following accelerator pedal operation
Accel Sens. No. 2 Volt %


HINT:

For numerical values of Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %, refer to the Data List.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)

NG

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Vehicle Speed.

Powertrain > Engine > Data List
Tester Display
Vehicle Speed
50003 234 10

e.

Read the value displayed on the tester.

Standard:
Tester Display Condition Specified Condition
Vehicle Speed Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING INTELLIGENT TESTER (FR, FL, RR, RL WHEEL SPEED)

NG

GO TO METER / GAUGE SYSTEM (SPEED SIGNAL CIRCUIT)

6.READ VALUE USING INTELLIGENT TESTER (FR, FL, RR, RL WHEEL SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Start the engine.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / All Data / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.

Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50003 105 1,2,3,4

e.

Read the value displayed on the tester.

Standard:
Tester Display Condition Specified Condition
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
OK
NG



OK

END

NG

INSPECT FRONT OR REAR SPEED SENSOR