Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › IGNITION SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074394 IGNITION SYSTEM G

2GR-FE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 19100P 1.PERFORM SPARK TEST

a.

Check for DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

If any DTC is present, perform troubleshooting in accordance with the procedure for that DTC.



b.

Remove the ignition coils and spark plugs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL


c.
A133895

Disconnect the 6 fuel injector connectors.


d.
A133897

Install the spark plug into the ignition coil, and then connect the ignition coil connector.


e.

Ground the spark plug.


f.

Check that spark occurs at each spark plug while the engine is being cranked.

NOTICE:
·

Be sure to ground the spark plugs when checking them.

·

Do not crank the engine for more than 2 seconds.

Cranking will stop if the engine switch is pushed again for models with cranking holding function.

·

If a spark plug has been struck or dropped, replace it.

·

If an ignition coil has been struck or dropped, replace it.



HINT:

If spark does not occur for any cylinder, perform the following Inspect Ignition Coil and Spark Test procedure.



g.

Connect the 6 fuel injector connectors.


h.


Hide 19500 2.INSPECT IGNITION COIL AND SPARK TEST

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Check that the wire harness side connector of the ignition coil is securely connected.

Result:
Result Action
NG Connect securely
OK Go to next step



b.

Perform a spark test on each ignition coil.

i.

Replace the ignition coil with a known good one.


ii.

Perform the spark test again.

Result:
Result Action
NG Go to next step
OK Replace ignition coil




c.

Perform a spark test on each spark plug.

i.

Replace the spark plug with a known good one.


ii.

Perform the spark test again.

Result:
Result Proceed to
NG Inspect the ignition system.
Click here(Click here)
OK Replace spark plug




Hide 19100P 3.CHECK SPARK PLUG

NOTICE:
·

Do not use a wire brush for cleaning.

·

Do not adjust the electrode gap of a spark plug.



HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
I039522C16
0.823,1.938 1.094,1.917 false 0.646,1.854 0.823,2.052 0.177,0.198 10 false *a
*a Ground


Check the electrode using a megohmmeter.

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (terminal part) - Body ground Always 10 MΩ or more


HINT:
·

If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.

·

If a megohmmeter is not available, perform the following simple inspection instead.





b.

Alternative inspection method.

i.

Quickly accelerate the engine to 4000 rpm 5 times.



iii.

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.




c.

Check the spark plug for any damage to its threads and insulator.

If there is any damage, replace the spark plug.

Recommended Spark Plug:
Manufacturer Spark Plug Type
DENSO FK20HR11



d.

Reference.

i.
A260264

Check the spark plug electrode gap.

Maximum Electrode Gap for Used Spark Plug:

1.4 mm (0.0551 in.)


If the gap is greater than the maximum, replace the spark plug.

NOTICE:

Never attempt to adjust the gap of a used spark plug


Electrode Gap for New Spark Plug:

1.0 to 1.1 mm (0.0394 to 0.0433 in.)




e.
A296690

Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

Standard Air Pressure:

588 kPa (6.0 kgf/cm2, 85 psi)


Standard Duration:

20 seconds or less


HINT:

Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.