Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › CYLINDER HEAD
RM2030EQ _51 Engine / Hybrid System _014635 2GR-FE ENGINE MECHANICAL _0074418 CYLINDER HEAD G

2GR-FE ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 11101 1.INSPECT CYLINDER HEAD SUB-ASSEMBLY

a.

Using a precision straightedge and feeler gauge, measure the warpage of the contact surface of the cylinder block sub-assembly and manifolds.

A293055C03
4,0.115 4.313,0.271 0.313,0.156 10 false *a 4.01,2.854 4.323,3.01 0.313,0.156 10 false *c 4,1.802 4.313,1.958 0.313,0.156 10 false *b
*a Cylinder Head Lower Side *b Intake Side
*c Intake Side - -


Standard Warpage:
Item Warpage
Cylinder head lower 0.05 mm (0.00197 in.)
Intake 0.08 mm (0.00315 in.)
Exhaust 0.08 mm (0.00315 in.)


Maximum Warpage:
Item Warpage
Cylinder head lower 0.10 mm (0.00394 in.)
Intake 0.10 mm (0.00394 in.)
Exhaust 0.10 mm (0.00394 in.)


If the warpage is greater than the maximum, replace the cylinder head sub-assembly.


Hide 2.INSPECT CYLINDER HEAD FOR CRACKS

a.
A120706

Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.

If cracked, replace the cylinder head sub-assembly.


Hide 13711 3.INSPECT INTAKE VALVE

a.
A121378

Using a micrometer, measure the diameter of the valve stem.

Valve stem diameter:

5.470 to 5.485 mm (0.2154 to 0.2159 in.)


If the valve stem is not as specified, check the oil clearance.


b.
A121379C10
0.524,1.296 0.677,1.479 0.153,0.183 10 *a
*a Margin thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.0 mm (0.0394 in.)


Minimum margin thickness:

0.5 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the intake valve.


c.
A121380C24
1.884,1.028 2.055,1.173 0.17,0.145 10 *a
*a Margin thickness


Using a vernier caliper, measure the valve overall length.

Standard overall length:

105.85 mm (4.1673 in.)


Minimum overall length:

105.35 mm (4.1476 in.)


If the overall length is less than the minimum, replace the intake valve.


Hide 13715 4.INSPECT EXHAUST VALVE

a.
A124001

Using a micrometer, measure the diameter of the valve stem.

Valve stem diameter:

5.465 to 5.480 mm (0.2152 to 0.2157 in.)


If the valve stem is not as specified, check the oil clearance.


b.
A121382C25
0.613,1.323 0.769,1.492 0.156,0.169 10 *a
*a Margin thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.0 mm (0.0394 in.)


Minimum margin thickness:

0.5 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the exhaust valve.


c.
A121383C19
1.932,0.968 2.107,1.134 0.175,0.166 10 *a
*a Overall Length


Using a vernier caliper, measure the valve overall length.

Standard overall length:

110.40 mm (4.3464 in.)


Minimum overall length:

109.90 mm (4.3268 in.)


If the overall length is less than the minimum, replace the exhaust valve.


Hide 11131 5.INSPECT INTAKE VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.


c.
A293056C04
1.479,1.167 1.792,1.323 0.313,0.156 10 *a
*a Width


Check the valve face and valve seat by using the following procedure:

i.

If Prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the valve.


ii.

If Prussian blue appears around the entire valve seat, the valve seat and valve face are concentric. If not, resurface the valve seat.


iii.

Check that the valve seat contacts the middle of the valve face with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).



Hide 11135 6.INSPECT EXHAUST VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.


c.
A293056C05
1.5,1.156 1.813,1.313 0.313,0.156 10 *a
*a Width


Check the valve face and valve seat by using the following procedure:

i.

If Prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the valve.


ii.

If Prussian blue appears around the entire valve seat, the valve seat and valve face are concentric. If not, resurface the valve seat.


iii.

Check that the valve seat contacts the middle of the valve face with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).



Hide 13711B 7.INSPECT INNER COMPRESSION SPRING

HINT:

Type A and Type B can be distinguished by the shape of the compression spring.


A336090C01
0.052,0.083 1.708,4.49 1.656,4.406 1.771,0.073 3.396,4.479 1.625,4.406 1.156,2.323 1.156,2.094 false 2.823,2.313 2.823,2.083 false 1.208,2.99 0.885,2.99 false 2.917,3.01 2.594,3.01 false 1.26,3.938 0.938,3.938 false 2.979,3.979 2.646,3.979 false 0.094,0.104 0.438,0.333 0.344,0.229 12 false *A 1.813,0.094 2.188,0.375 0.375,0.281 12 false *B 1.094,2.375 1.406,2.531 0.313,0.156 10 false *1 1.271,2.917 1.583,3.073 0.313,0.156 10 false *2 1.313,3.875 1.625,4.031 0.313,0.156 10 false *3 0.635,2.49 0.948,2.646 0.313,0.156 10 false *a 1.417,0.917 1.646,1.125 0.229,0.208 10 false *b 3.125,0.906 3.354,1.115 0.229,0.208 10 false *b 2.354,2.479 2.667,2.635 0.313,0.156 10 false *a 2.76,2.354 3.073,2.51 0.313,0.156 10 false *1 2.979,2.927 3.292,3.083 0.313,0.156 10 false *2 3.031,3.917 3.344,4.073 0.313,0.156 10 false *3
*A Type A
*B Type B
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Spring Retainer
*3 Inner Compression Spring
*a Valve Spring Retainer Diameter
*b No. 1 Valve Rocker Arm Sub-assembly Roller Width


Type No. 1 Valve Rocker Arm Sub-assembly Roller Width Valve Spring Retainer Diameter Inner Compression Spring Shape
A 10.7 mm (0.421 in.) 23.4 mm (0.921 in.) Straight
B 8.0 mm (0.315 in.) 18.9 mm (0.744 in.) Taper

a.

Type A:

i.
A109669

Using a vernier caliper, measure the free length of the inner compression spring.

Free length:

45.91 mm (1.8075 in.)


If the free length is not as specified, replace the inner compression spring.


ii.
A293057C02
1.177,0.115 1.49,0.271 0.313,0.156 10 *a
*a Deviation


Using a steel square, measure the deviation of the inner compression spring.

Maximum deviation:

1.0 mm (0.0394 in.)


If the deviation is greater than the maximum, replace the inner compression spring.



b.

Type B:

i.
A333599

Using a vernier caliper, measure the free length of the inner compression spring.

Standard Free Length:

50.55 mm (1.9902 in.)


If the free length is not as specified, replace the inner compression spring.


ii.
A319225C14
0.896,1.448 1.208,1.604 0.313,0.156 10 false *b 1.438,0.375 1.75,0.531 0.313,0.156 10 false *a
*a Deviation
*b 40 mm (1.57 in.)


Using a steel square, measure the deviation of the inner compression spring.

Maximum Deviation:

1.4 mm (0.0551 in.)


If the deviation is more than the maximum, replace the inner compression spring.



Hide 8.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A120707

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Bush inside diameter:

5.510 to 5.530 mm (0.2169 to 0.2177 in.)



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:
Item Clearance
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Clearance
Intake 0.08 mm (0.00315 in.)
Exhaust 0.10 mm (0.00394 in.)


If the clearance is greater than the maximum, replace the valve and valve guide bush.