Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › CYLINDER BLOCK
RM2030EQ _51 Engine / Hybrid System _014635 2GR-FE ENGINE MECHANICAL _0074419 CYLINDER BLOCK A

2GR-FE ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Check that the matchmarks on the connecting rod sub-assembly and connecting rod cap are aligned.

HINT:

The matchmarks on the connecting rod sub-assembly and connecting rod cap are guides for the correct reassembly.



b.
A293062
1.667,1.01 1.667,1 false
V100136

Engine Front


Remove the 2 connecting rod cap bolts.


c.
A129761

Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

HINT:

Keep the lower bearing inserted to the connecting rod cap.



d.
A129720
0.286,0.503 0.453,0.66 0.167,0.157 10 *1 1.883,0.905 0.508,0.601 false
*1 Ridge Reamer


Using a ridge reamer, remove all the carbon from the top of the cylinder.


e.

Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

HINT:
·

Keep the bearing, connecting rod and cap together.

·

Arrange the piston and connecting rod assemblies in the correct order.




Hide 13041 2.REMOVE CONNECTING ROD BEARING

HINT:

Arrange the removed parts in the correct order.


Hide 13011 3.REMOVE PISTON RING SET

a.
A129724
0.595,0.472 0.745,0.626 0.15,0.154 10 *1 0.811,0.551 1.503,0.551 false
*1 Piston Ring Expander


Using a piston ring expander, remove the 2 compression rings.


b.

Remove the oil ring expander and 2 side rails by hand.

HINT:

Arrange the removed parts in the correct order.



Hide 13101 4.REMOVE PISTON

a.
A129725

Check the fitting condition between the piston and piston pin.

i.

Try to move the piston back and forth on the piston pin.

If any movement is felt, replace the piston and pin as a set.



b.
A129726

Disconnect the connecting rod from the piston.

i.

Using a screwdriver, pry off the piston pin hole snap rings from the piston.


ii.
A109729

Gradually heat the piston to approximately 80°C (176°F).


iii.
A129728

Using a brass bar and a plastic hammer, lightly tap out the piston pin and remove the connecting rod sub-assembly.

HINT:
·

The piston and piston pin are a matched set.

·

Arrange the pistons, piston pins, piston pin hole snap rings, connecting rods and connecting rod bearings in the correct order.





c.
A129729

Using a gasket scraper, remove the carbon from the piston top.

NOTICE:

Be careful not to scratch a piston.



d.

Using a groove cleaning tool, clean the piston ring grooves.


e.
A129731

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.



Hide 13411 5.REMOVE CRANKSHAFT

a.
A293063
2.094,1.885 2.25,2.083 0.156,0.198 10 1 2.573,1.479 2.729,1.677 0.156,0.198 10 4 2.99,1.167 3.146,1.365 0.156,0.198 10 3 3.313,1.01 3.417,1.177 0.104,0.167 10 2 0.146,1.094 0.302,1.292 0.156,0.198 10 6 0.781,0.521 0.938,0.719 0.156,0.198 10 7 1.188,0.313 1.344,0.51 0.156,0.198 10 8 1.5,0.104 1.656,0.302 0.156,0.198 10 5

Uniformly loosen and remove the 8 crankshaft bearing cap bolts and the 8 seal washers in several steps and in the sequence shown in the illustration.


b.
A293064
0.375,1.521 0.531,1.719 0.156,0.198 10 1 0.344,1.031 0.5,1.229 0.156,0.198 10 9 0.24,0.698 0.542,0.927 0.302,0.229 10 10 0.292,0.302 0.448,0.5 0.156,0.198 10 2 1.01,0.302 1.167,0.5 0.156,0.198 10 6 0.917,0.708 1.229,0.927 0.313,0.219 10 14 0.938,1.042 1.208,1.24 0.271,0.198 10 13 1.01,1.49 1.115,1.688 0.104,0.198 10 5 2.406,0.354 2.563,0.521 0.156,0.167 10 8 2.417,0.719 2.688,0.958 0.271,0.24 10 16 2.406,1.052 2.688,1.281 0.281,0.229 10 15 2.427,1.479 2.583,1.646 0.156,0.167 10 7 3.031,1.51 3.188,1.677 0.156,0.167 10 3 3.073,1.073 3.365,1.375 0.292,0.302 10 11 3.073,0.729 3.344,1 0.271,0.271 10 12 3.042,0.344 3.313,0.615 0.271,0.271 10 4

Uniformly loosen the 16 crankshaft bearing cap bolts, in several steps and in the sequence shown in the illustration.


c.
A122567
1.865,1.51 2.615,2.26 true 0.542,2.417 0.896,2.833 true 1.708,2.885 2.01,2.563 true 1.24,3.76 0.875,4.167 0.875,4.167 1.5,3.969 false 0.677,4.031 0.854,4.229 0.177,0.198 10 *a 2.604,2.302 2.792,2.5 0.188,0.198 10 *1 2.104,2.427 2.281,2.594 0.177,0.167 10 *3 0.333,2.302 0.51,2.469 0.177,0.167 10 *2
*1 Protective Tape
*2 Cylinder Block
*3 Bearing Cap
*a Joint Surface


Using a screwdriver, pry out the crankshaft bearing caps. Remove the 4 crankshaft bearing caps and lower crankshaft bearings.

NOTICE:
·

Push up on the cap slowly and evenly, alternating from the right and left side so that the bearing cap can be removed.

·

Be careful not to damage the joint surface of the cylinder block and the crankshaft bearing cap.




d.

Remove the crankshaft.


Hide 11711 6.REMOVE CRANKSHAFT BEARING

a.

Remove the upper crankshaft bearings and lower crankshaft bearings.

HINT:

Arrange the removed parts in the correct order.



Hide 11011 7.REMOVE CRANKSHAFT THRUST WASHER SET

a.
A109726

Remove the upper crankshaft thrust washers from the cylinder block sub-assembly.


Hide 15708 8.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A120734

Using a 5 mm hexagon wrench, remove the 3 bolts and No. 1 oil nozzle sub-assemblies.


b.

Check the 3 oil nozzles for damage or clogging.

If necessary, replace the No. 1 oil nozzle sub-assembly.


Hide 9.CLEAN CYLINDER BLOCK