Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › CYLINDER BLOCK
RM2030EQ _51 Engine / Hybrid System _014635 2GR-FE ENGINE MECHANICAL _0074419 CYLINDER BLOCK A

2GR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the piston and piston ring.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 15708 1.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A120734

Using a 5 mm hexagon wrench, install the No. 1 oil nozzle sub-assemblies with the 3 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 13101 2.INSTALL PISTON

a.
A131876
1.414,1.73 1.569,1.878 0.156,0.148 10 *1 2.293,1.581 1.63,1.8 false
*1 Service Hole


Using a screwdriver, install a new piston pin hole snap ring at one end of the piston pin hole.

HINT:

Confirm that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.



b.
A125895

Gradually heat the piston to approximately 80°C (176°F).


c.

Coat the piston pin with engine oil.


d.
A131878
0.148,0.305 0.303,0.453 0.155,0.148 10 *a 2.277,0.399 0.355,0.399 0.355,0.399 1.077,1.262 false
*a Front Mark


Align the front marks of the piston and connecting rod, and push in the piston pin with your thumb.

HINT:

The piston and pin are a matched set.



e.
A107551

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


f.
A131879
1.841,1.432 2.008,1.577 0.166,0.146 10 *1 2.248,1.637 2.026,1.514 false
*1 Service Hole


Using a screwdriver, install a new piston pin hole snap ring at the other end of the piston pin hole.

HINT:
·

Confirm that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.

·

Perform "Inspection After Repair" after replacing the piston.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Hide 13011 3.INSTALL PISTON RING SET

a.

Install the oil ring expander and 2 side rails by hand.


b.
A131880
0.787,0.169 0.946,0.329 0.158,0.16 10 *1 0.427,3.802 0.592,3.951 0.166,0.149 10 *6 1.555,3.802 1.714,3.96 0.159,0.158 10 *7 2.83,3.922 3.0,4.076 0.17,0.154 10 *5 1.909,3.135 2.079,3.31 0.17,0.175 10 *3 2.262,4.053 2.433,4.201 0.171,0.148 10 *4 2.446,2.87 2.612,3.018 0.166,0.148 10 *2 2.551,3.518 2.107,3.219 false 2.929,3.402 2.648,2.951 false 2.717,3.881 2.472,4.119 false 1.623,0.421 0.975,0.26 false
*1 Piston Ring Expander
*2 Upper Side Rail
*3 Oil Ring Expander
*4 Lower Side Rail
*5 Oil Ring
*6 No. 1 Ring
*7 No. 2 Ring


Using a piston ring expander, install the compression ring as shown in the illustration.


c.
A131881
1.24,1.708 0.688,1.313 false 1.625,2.625 1.792,2.792 0.167,0.167 10 *5 1.625,0.51 1.792,0.677 0.167,0.167 10 *1 0.906,2.333 1.073,2.5 0.167,0.167 10 *4 0.833,0.927 1.01,1.094 0.177,0.167 10 *2 0.51,1.188 0.667,1.354 0.156,0.167 10 *a 0.594,1.615 0.76,1.76 0.167,0.146 10 *3
*1 Lower Side Rail
*2 No. 2 Ring
*3 Oil Ring Expander
*4 No. 1 Ring
*5 Upper Side Rail
*a Front Mark


Position the piston rings so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the ring ends.


HINT:

Perform "Inspection After Repair" after replacing the piston ring.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 11711 4.INSTALL CRANKSHAFT BEARING

a.
A124282
0.779,0.424 0.935,0.585 0.156,0.161 10 *1 2.549,0.43 2.72,0.591 0.17,0.161 10 *2 0.505,2.56 1.189,2.768 0.684,0.208 10 21.0 mm 2.35,2.56 3.034,2.768 0.684,0.208 10 18.0 mm
*1 No. 1 and No. 4 Journal Bearing
*2 No. 2 and No. 3 Journal Bearing


Clean the main journal and both surfaces of the bearings.

NOTICE:

Main bearings come in widths between 18.0 mm (0.709 in.) and 21.0 mm (0.827 in.). Install the 21.0 mm (0.827 in.) bearings in the No. 1 and No. 4 cylinder block journal positions with the main bearing cap. Install the 18.0 mm (0.709 in.) bearings in the No. 2 and No. 3 positions.



b.
A293066
1.719,2.875 2.75,1.958 2.75,1.958 2.615,2.885 false 2.813,1.865 3.125,2.021 0.313,0.156 10 *1 1.667,3.771 1.979,3.927 0.313,0.156 10 *a 2.656,3.781 2.969,3.938 0.313,0.156 10 *b
*1 Upper Bearing
*a CORRECT
*b INCORRECT


Install the upper crankshaft bearing.

i.

Install the upper crankshaft bearings to the cylinder block as shown in the illustration.

NOTICE:
·

Do not apply engine oil to the bearings and the contact surfaces.

·

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.





c.
A131826
1.031,1.948 0.76,2.094 false 2.365,2.625 2.063,2.208 true 0.573,2.021 0.75,2.188 0.177,0.167 10 *a 1.854,2.094 2.063,2.271 0.208,0.177 10 *1 0.969,2.927 1.094,3.219 0.125,0.292 10 A 2.292,2.938 2.417,3.229 0.125,0.292 10 B
*1 Vernier Caliper
*a Mark 1, 2, 3, 4 or 5


Install the lower crankshaft bearing.

i.

Install the lower crankshaft bearings to the crankshaft bearing caps.


ii.

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and the lower crankshaft bearing edge.

Dimension (A - B):

0.7 mm (0.0276 in.) or less


NOTICE:

Do not apply engine oil to the crankshaft bearings and the contact surfaces.




Hide 11011 5.INSTALL CRANKSHAFT THRUST WASHER SET

a.

Apply engine oil to the crankshaft thrust washer.


b.
A106233
2.317,0.147 2.495,0.353 0.178,0.206 10 *1 1.108,1.254 2.275,0.297 2.275,0.297 1.935,1.485 false
*1 Oil Grooves


Install the 2 upper crankshaft thrust washers under the No. 2 journal position of the cylinder block sub-assembly with the oil grooves facing outward.


Hide 13411 6.INSTALL CRANKSHAFT

a.

Apply engine oil to the upper bearing, then place the crankshaft on the cylinder block.


b.
A121711
0.418,0.166 0.574,0.346 0.156,0.18 10 *1 0.812,3.04 0.99,3.209 0.178,0.169 10 *a 0.884,1.293 0.884,0.259 false 2.791,1.294 2.791,0.248 2.791,0.248 0.634,0.248 false 2.15,1.29 2.15,0.248 false 1.548,1.274 1.548,0.248 false 0.915,2.741 0.915,3.03 false 2.827,2.741 2.827,2.901 2.827,2.901 0.915,2.901 false 1.573,2.741 1.573,2.901 false 2.169,2.741 2.169,2.901 false
*1 Projection
*a Number Mark


Confirm the projections and numbers on the main bearing caps and install the crankshaft bearing caps on the cylinder block.

HINT:

A number is marked on each main bearing cap to indicate the installation position.



c.

Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap bolts.


d.

Temporarily install the 8 crankshaft bearing cap bolts to the inside positions.


e.
A134893
1.094,2.135 0.354,2.875 true 1.594,3.75 1.76,3.938 0.167,0.188 10 *b 0.198,2.885 0.375,3.042 0.177,0.156 10 *a
*a Less than 6 mm
*b Bolt Length 100 to 102 mm


Insert the crankshaft bearing cap with your hand until the clearance between the crankshaft bearing cap and the cylinder block is less than 6 mm (0.236 in.) by marking the 2 internal crankshaft bearing cap bolts as a guide.

Bolt length:

100 to 102 mm (3.94 to 4.02 in.)



f.
A131829

Using a plastic hammer, lightly tap the crankshaft bearing cap to ensure a proper fit.


g.

Apply a light coat of engine oil to the threads and under the heads of the 8 crankshaft bearing cap bolts.


h.
A134894
1.613,3.776 1.785,3.931 0.172,0.155 10 *a
*a Bolt Length


Install the 8 crankshaft bearing cap bolts to the outside positions.

Bolt length:

105.5 to 107.5 mm (4.15 to 4.23 in.)



i.

Install the crankshaft bearing cap bolts.

HINT:

The crankshaft bearing cap bolts are tightened in 2 progressive steps.



j.

Step 1

i.
A306347
2.417,0.719 2.573,0.917 0.156,0.198 10 false 1 2.469,1.031 2.625,1.229 0.156,0.198 10 false 2 0.969,0.729 1.125,0.927 0.156,0.198 10 false 3 0.979,1.073 1.135,1.271 0.156,0.198 10 false 4 3.073,0.729 3.229,0.927 0.156,0.198 10 false 5 3.063,1.073 3.219,1.271 0.156,0.198 10 false 6 0.313,0.708 0.469,0.906 0.156,0.198 10 false 7 0.323,1.063 0.479,1.26 0.156,0.198 10 false 8 2.396,0.354 2.552,0.552 0.156,0.198 10 false 9 2.385,1.479 2.698,1.677 0.313,0.198 10 false 10 0.969,0.333 1.281,0.531 0.313,0.198 10 false 11 0.979,1.51 1.292,1.708 0.313,0.198 10 false 12 3.031,0.333 3.344,0.531 0.313,0.198 10 false 13 3.031,1.5 3.344,1.698 0.313,0.198 10 false 14 0.344,0.24 0.656,0.438 0.313,0.198 10 false 15 0.333,1.448 0.646,1.646 0.313,0.198 10 false 16

Install and uniformly tighten the 16 crankshaft bearing cap bolts in several steps and in the sequence shown in the illustration.

Torque:
61 N*m (622 kgf*cm, 45 ft.*lbf)

If any of the crankshaft bearing cap bolts does not meet the torque specified, replace it.



k.

Step 2

i.
A293067
2.229,0.51 2.49,0.24 true 2.542,0.146 2.854,0.302 0.313,0.156 10 *a 1.313,0.281 1.625,0.438 0.313,0.156 10 *b
*a Paint Mark
*b Turn 90°
V100136

Engine Front


Mark the front of the bearing cap bolts with paint.


ii.

Retighten the bearing cap bolts 90° in the sequence shown in the illustration.


iii.

Check that the painted mark is now at a 90° angle to the front of the engine.



l.
A306357
1.979,0.354 2.75,0.271 2.75,0.271 2.906,0.792 false 1.115,0.177 1.344,0.427 0.229,0.25 10 false 1 0.75,0.49 0.906,0.688 0.156,0.198 10 false 2 0.073,0.979 0.229,1.177 0.156,0.198 10 false 3 1.438,0.073 1.594,0.271 0.156,0.198 10 false 4 2.604,1.625 2.76,1.823 0.156,0.198 10 false 5 2.979,1.292 3.135,1.49 0.156,0.198 10 false 6 3.26,1.104 3.417,1.302 0.156,0.198 10 false 7 2.104,1.958 2.26,2.156 0.156,0.198 10 false 8 2.771,0.146 3.229,0.344 0.458,0.198 10 false (A)

Install 8 new seal washers and uniformly tighten the 8 crankshaft bearing cap bolts in several steps and in the sequence shown in the illustration.

Torque:
52 N*m (525 kgf*cm, 38 ft.*lbf)

Bolt Length:
Item Length
Bolt A 45 mm (1.77 in.)
Except bolt A 30 mm (1.18 in.)



m.

Check that the crankshaft turns smoothly.


n.

Check the crankshaft thrust clearance.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>CYLINDER BLOCK>INSPECTION


Hide 13041 7.INSTALL CONNECTING ROD BEARING

a.

Install the connecting rod bearing to the connecting rod and connecting rod cap.


b.
A293068
0.552,3.031 0.729,3.031 0.729,3.031 0.854,3.573 false 0.354,2.958 0.667,3.115 0.313,0.156 10 *1 2,3.76 2.156,3.958 0.156,0.198 10 A 3.104,3.771 3.26,3.969 0.156,0.198 10 B
*1 Vernier Caliper


Using a vernier caliper, measure the distance between the connecting rod and bearing cap edges and the connecting rod bearing edge.

Dimension (A - B):

0.7 mm (0.0276 in.) or less


NOTICE:

Do not apply engine oil to the bearings and the contact surfaces.



Hide 8.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.


b.
A131881
1.24,1.708 0.688,1.313 false 1.625,2.625 1.792,2.792 0.167,0.167 10 *5 1.625,0.51 1.792,0.677 0.167,0.167 10 *1 0.906,2.333 1.073,2.5 0.167,0.167 10 *4 0.833,0.927 1.01,1.094 0.177,0.167 10 *2 0.51,1.188 0.667,1.354 0.156,0.167 10 *a 0.594,1.615 0.76,1.76 0.167,0.146 10 *3
*1 Lower Side Rail
*2 No. 2 Ring
*3 Oil Ring Expander
*4 No. 1 Ring
*5 Upper Side Rail
*a Front Mark


Position the piston rings so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the ring ends.



c.
A131886
1.821,3.083 1.977,3.24 0.156,0.157 10 *a 1.329,2.927 1.887,3.032 1.887,3.032 2.549,2.531 false
*a Front Mark
V100136

Engine Front


Using a piston ring compressor, push the correctly numbered piston and connecting rod assembly into the cylinder with the front mark of the piston facing forward.

NOTICE:

Match the numbered connecting rod cap with the connecting rod.



d.
A293062
0.51,1.656 1.74,1.292 true 0.354,1.615 0.667,1.813 0.313,0.198 10 *a
*a Front Mark
V100136

Engine Front


Check that the front mark of the connecting rod cap is facing forward.


e.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


f.

Install the connecting rod cap bolts.

HINT:

The connecting rod cap bolts are tightened in 2 progressive steps.



g.

Step 1

i.
A131887

Install and alternately tighten the bolts of the connecting rod cap in several steps.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)



h.
A101478
1.233,0.404 1.384,0.585 0.152,0.182 10 *b 2.085,0.747 2.575,0.475 false 2.623,0.372 2.824,0.528 0.201,0.157 10 *a
*a Paint Mark
*b Turn 90°
V100136

Engine Front


Step 2

i.

Mark the front side of each connecting rod cap bolt with paint.


ii.

Retighten the cap bolts 90° as shown in the illustration.


iii.

Check that the painted mark is now at a 90° angle to the front.



i.

Confirm that the crankshaft turns smoothly.


j.

Check the connecting rod thrust clearance.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>CYLINDER BLOCK>INSPECTION