Home › Engine / Hybrid System › 2GR-FE FUEL › FUEL SYSTEM
RM2030EQ _51 Engine / Hybrid System _014636 2GR-FE FUEL _0074420 FUEL SYSTEM G

2GR-FE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK

a.

Check fuel pump operation.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON and turn the intelligent tester on.

NOTICE:

Do not start the engine.



iii.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 230

iv.

Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, fuel pump control ECU, ECM and wiring connectors.



b.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.



c.

Turn the ignition switch off.


d.

Disconnect the intelligent tester from the DLC3.


Hide 2.CHECK FUEL PRESSURE

a.

Discharge the fuel system pressure.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL SYSTEM>PRECAUTION


b.

Using a voltmeter, measure the battery voltage.

Standard voltage:

11 to 14 V



c.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Disconnect the fuel hose from the fuel main tube.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL SYSTEM>PRECAUTION


e.
A255967C06
2.813,0.438 2.594,0.229 2.594,0.229 2.458,0.229 false 1.677,1.635 2.083,1.219 2.083,1.219 2.177,1.219 false 0.771,2.365 0.771,2.552 false 1.5,0.802 1.5,1.063 false 0.823,0.521 0.625,0.521 false 1.063,1.031 1.063,1.198 false 1.594,3.333 1.74,3.073 1.74,3.073 1.833,3.073 false 1.302,3.979 1.396,4.073 1.396,4.073 1.51,4.073 false 2.281,3.583 2.281,3.844 false 2.719,3.333 2.719,3.635 false 2.281,0.177 2.646,0.417 0.365,0.24 10 *3 2.25,1.146 2.604,1.344 0.354,0.198 10 *4 0.708,2.583 1.052,2.792 0.344,0.208 10 *7 1,1.219 1.313,1.438 0.313,0.219 10 *2 0.458,0.469 0.865,0.698 0.406,0.229 10 *1 1.427,1.094 1.792,1.292 0.365,0.198 10 *1 2.229,3.885 2.552,4.073 0.323,0.188 10 *6 1.896,2.99 2.26,3.198 0.365,0.208 10 *1 1.573,4 1.906,4.198 0.333,0.198 10 *5 2.667,3.656 2.99,3.844 0.323,0.188 10 *8
*1 SST
(Hose Band)
*2 SST
(T-joint)
*3 SST
(Gauge)
*4 SST
(Hose Joint)
*5 SST
(Hose)
*6 SST
(Fuel Tube Connector)
*7 Fuel Tube Sub-assembly (Vehicle Side)
*8 Fuel Pipe (Vehicle Side)


Install SST (EFI fuel pressure gauge) as shown in the illustration.

SST
09268-45101  (09268-41250, 09268-41260, 09268-41280, 09268-41500, 09268-41700, 95336-08070)


f.

Wipe up any spilled gasoline.


g.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



h.

Connect the intelligent tester to the DLC3.


i.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 230

j.

Measure the fuel pressure.

Standard fuel pressure:

380 to 420 kPa (3.9 to 4.3 kgf/cm2, 55 to 61 psi)


·

If the fuel pressure is greater than the standard value, replace the fuel pressure regulator.

·

If the fuel pressure is less than the standard value, check the fuel hoses and connections, fuel pump, fuel pump control ECU, fuel filter and fuel pressure regulator.



k.

Disconnect the intelligent tester from the DLC3.


l.

Start the engine.


m.

Measure the fuel pressure at idle.

Standard fuel pressure:

380 to 420 kPa (3.9 to 4.3 kgf/cm2, 55 to 61 psi)



n.

Stop the engine.


o.

Check that the fuel pressure remains as specified for 5 minutes after the engine stops.

Standard fuel pressure:

147 kPa (1.5 kgf/cm2, 21 psi) or more


If the fuel pressure is not as specified, check the fuel pump, pressure regulator and/or fuel injectors.


p.

After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST to prevent gasoline from splashing.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



q.

Reconnect the fuel tube to the main fuel tube (fuel tube connector).


r.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


s.

Inspect for fuel leaks (See step 1).