Home › Engine / Hybrid System › 2GR-FE LUBRICATION › OIL AND OIL FILTER
RM2030EQ _51 Engine / Hybrid System _014640 2GR-FE LUBRICATION _0074451 OIL AND OIL FILTER A

2GR-FE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. Skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

·

In order to preserve the environment, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 1.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil drain plug and drain the oil into a container.


c.

Clean the oil drain plug.


d.

Install the oil drain plug with a new gasket.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 15620 2.REMOVE OIL FILTER CAP ASSEMBLY

a.
A204919
1.604,0.385 1.427,0.385 1.427,0.385 1.146,0.646 false 2.688,1.052 2.531,1.052 2.531,1.052 2.292,1.281 false 1.656,0.281 1.875,0.49 0.219,0.208 10 false *1 2.729,0.948 2.948,1.156 0.219,0.208 10 false *2
*1 Pipe
*2 Hose


Connect the hose with an inside diameter of 15 mm (0.591 in.) to the pipe.


b.
A127997

Remove the oil filter drain plug from the oil filter cap.


c.
A160741
2.313,1.688 2.688,1.688 false 2.49,2.365 2.813,2.365 2.813,2.365 2.813,1.854 true 2.927,2.417 2.927,1.917 true 2.135,1.594 2.323,1.75 0.188,0.156 10 false *1 2.323,2.26 2.51,2.417 0.188,0.156 10 false *2 2.844,2.448 3.031,2.604 0.188,0.156 10 false *3
*1 Cap
*2 O-ring
*3 Pipe


Insert the pipe with the hose into the oil filter cap.

NOTICE:

Be sure to insert the pipe with the O-ring installed on the oil filter cap.


HINT:

Place the hose end into a container before draining oil from the hose.



d.
A127999

Make sure that oil is completely drained, and remove the pipe and O-ring.

HINT:

Be sure to turn the pipe in the direction of the arrow to remove it.



e.
A128000
1.958,1.542 2.323,1.542 false 2.354,1.458 2.656,1.594 0.302,0.135 10 false SST

Using SST, remove the oil filter cap.

SST
09228-06501  


f.
A128001
2.188,0.448 2.427,0.167 2.427,0.167 2.573,0.167 false 2.135,1.396 2.385,1.583 2.385,1.583 2.615,1.583 true 2.604,0.823 2.531,0.823 2.531,0.823 2.271,1.021 false 2.604,0.073 2.792,0.25 0.188,0.177 10 false *1 2.635,0.729 2.823,0.906 0.188,0.177 10 false *2 2.635,1.49 2.823,1.667 0.188,0.177 10 false *3
*1 Oil Filter Element
*2 Oil Filter Cap
*3 O-ring


Remove the oil filter element and O-ring from the oil filter cap.

NOTICE:

Do not use any tools to remove the O-ring in order to prevent the cap from being damaged. Be sure to remove it by hand.



Hide 15620 3.INSTALL OIL FILTER CAP ASSEMBLY

a.

Clean the inside of the oil filter cap, threads and O-ring groove.


b.
A268595
1.521,1.052 1.583,0.823 1.583,0.823 1.667,0.823 false 3.094,1.156 3.146,0.927 3.146,0.927 3.229,0.927 false 1.708,0.729 1.875,0.875 0.167,0.146 10 false *1 3.26,0.823 3.427,0.969 0.167,0.146 10 false *1 0.875,1.802 1.042,1.958 0.167,0.156 10 false *a 2.438,1.802 2.604,1.958 0.167,0.156 10 false *b
*1 O-ring
*a CORRECT
*b INCORRECT


Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.

NOTICE:
·

Be sure to install the O-ring in the proper location, otherwise oil may leak.

·

Do not twist the O-ring.




c.

Install a new oil filter element to the oil filter cap.


d.

Remove all dirt and foreign matter from the installation surface and the inside of the cap on the engine side.


e.

Apply a light coat of engine oil to the O-ring again and install the oil filter cap.

NOTICE:

Make sure that the O-ring does not get caught between the parts.



f.
A275939
2.406,1.604 2.615,1.604 false 2.75,0.823 2.667,0.823 2.667,0.823 2.458,1.063 true 2.552,0.375 2.771,0.375 false 0.615,1.365 0.396,1.365 false 2.958,1.219 3.146,1.396 0.188,0.177 10 false *a 2.646,1.521 2.833,1.698 0.188,0.177 10 false *1 2.781,0.729 2.969,0.906 0.188,0.177 10 false *2 2.802,0.271 2.99,0.448 0.188,0.177 10 false *3 0.115,1.271 0.438,1.448 0.323,0.177 10 false SST
*1 Oil Filter Cap
*2 O-ring
*3 Oil Filter Bracket
*a No Gap


Using SST, install the oil filter cap.

SST
09228-06501  

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.



g.
A161390
2.979,1.833 2.198,1.833 true 2.031,1.729 2.229,1.906 0.198,0.177 10 false *1
*1 O-ring


Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.

NOTICE:

Remove all dirt and foreign matter from the installation surface.



h.

Install the oil filter drain plug to the oil filter cap.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Make sure that the O-ring does not get caught between the parts.



Hide 4.ADD ENGINE OIL

a.
A308107

Add clean engine oil and install the oil filler cap.

NOTICE:

Do not allow engine oil adhere to the moving parts of the belt tensioner, as this may cause malfunctions.

If engine oil is on the location indicated by the arrow, replace the belt tensioner.


Standard Oil Grade:
Oil Grade Oil Viscosity (SAE)
API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil
·

5W-30


·

10W-30


API grade SL, SM or SN multigrade engine oil
·

15W-40


·

20W-50




Standard Capacity:
Item Standard Condition
Drain and refill with oil filter change 6.1 liters (6.4 US qts, 5.4 Imp. qts)
Drain and refill without oil filter change 5.7 liters (6.0 US qts, 5.0 Imp. qts)
Dry fill 6.8 liters (7.2 US qts, 6.0 Imp. qts)



Hide 5.INSPECT FOR OIL LEAK