Home › Engine / Hybrid System › 2GR-FE STARTING › STARTER
RM2030EQ _51 Engine / Hybrid System _014641 2GR-FE STARTING _0074455 STARTER A

2GR-FE STARTING  STARTER  REASSEMBLY  


PROCEDURE

Hide 28255 1.INSTALL PLANETARY GEAR

a.
A305692
1.719,2.208 1.708,2.229 false
V100135

High-temperature grease


Apply high-temperature grease to the planetary gears and pin parts of the planetary shaft.


b.

Install the 3 planetary gears.


Hide 28117A 2.INSTALL RUBBER SEAL

a.
A194763

Install the rubber seal to the repair service starter kit.


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

a.
A305434
2.323,1.417 2.313,1.417 false
V100135

High-temperature grease


Apply high-temperature grease to the armature shaft.


b.
A305435
1.406,0.521 1.406,0.5 false
V100135

High-temperature grease


Apply high-temperature grease to the washer and bearing, as shown in the illustration.


c.
A194762
1.729,0.479 1.448,0.292 1.448,0.292 1.385,0.292 false 1.219,0.219 1.417,0.406 0.198,0.188 10 false *1
*1 Snap Ring Pliers


Install the starter armature assembly to the starter commutator end frame assembly.


d.

Install the washer.


e.

Using snap ring pliers, securely install a new snap ring to the armature shaft groove.

NOTICE:

Be sure to install the snap ring, properly because it easily expands.



f.
A194767
0.476,0.973 0.703,1.148 0.228,0.175 10 *a
*a Length


Using a vernier caliper, measure the length of the snap ring.

Maximum length:

5.0 mm (0.197 in.)


If the length is more than the maximum, replace the snap ring with a new one.


Hide 28132A 4.INSTALL STARTER COMMUTATOR END FRAME COVER

a.
A197189

Install the starter commutator end frame cover to the starter commutator end frame assembly.


Hide 28177 5.INSTALL STARTER ARMATURE PLATE

a.
A194768
1.025,1.457 1.197,1.646 0.172,0.189 10 *a 1.494,1.648 1.295,1.545 1.295,1.545 1.215,1.545 false 2.814,1.506 3.003,1.695 0.189,0.189 10 *b 2.882,1.044 2.882,1.492 false
*a Keyway
*b Key


Insert the armature plate into the starter yoke assembly.


b.

Align the keyway of the starter armature plate with the key inside the starter yoke, and install the starter armature plate.


Hide 28130 6.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A197184
2.51,0.948 2.417,0.677 2.417,0.677 2.365,0.677 false 1.219,0.563 1.344,0.302 1.344,0.302 1.417,0.302 false 1.448,0.208 1.656,0.375 0.208,0.167 10 false *a 2.156,0.583 2.323,0.75 0.167,0.167 10 false *b
*a Cutout
*b Rubber


Align the rubber of the end frame with the cutout of the starter yoke assembly.


b.

Install the starter commutator end frame assembly to the starter yoke assembly.

NOTICE:

The magnet of the starter yoke assembly may attract the starter armature when the starter commutator end assembly frame is installed, causing the magnet to break.



Hide 28120 7.INSTALL STARTER YOKE ASSEMBLY

a.
A197185
1.771,1.073 2.021,0.885 2.021,0.885 2.094,0.885 false 1.615,1.094 0.979,1.417 0.979,1.417 0.854,1.417 false 0.677,1.333 0.958,1.615 0.281,0.281 10 false *b 2.167,0.802 2.396,1.042 0.229,0.24 10 false *a
*a Protrusion
*b Cutout


Align the protrusion of the starter yoke assembly with the cutout of the repair service starter kit.


b.
A194758

Install the starter yoke assembly with the 2 through-bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28150 8.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
A305436
2.188,0.531 2.344,0.729 0.156,0.198 10 false .
V100135

High-temperature grease


Apply high-temperature grease to the plunger and the lever.


b.
A197186

Pull the pinion gear and push down the lever.


c.
A197187
0.802,0.771 1.448,0.51 1.448,0.51 1.552,0.51 false 1.01,1.052 1.49,1.167 1.49,1.167 1.604,1.167 false 1.615,0.438 1.844,0.646 0.229,0.208 10 false *1 1.646,1.083 2.063,1.281 0.417,0.198 10 false *2
*1 Plunger
*2 Pinion Drive Lever


Temporarily install the magnet starter switch assembly by hooking the plunger into the upper side of the pinion drive lever.


d.
A194757

Install the magnet starter switch assembly with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


e.
A194756

Connect the lead wire to the magnet starter switch assembly with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)