Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT › 2012.02–2013.07
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0074472 AUTOMATIC TRANSAXLE UNIT A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

a.

Check bearing position and installation direction.

C153478N02
4.97,2.957 5.095,3.105 0.125,0.148 10 C 3.82,6.027 3.934,6.187 0.114,0.16 10 B 1.411,7.499 1.532,7.663 0.121,0.164 10 A

C138529N02
2.709,3.089 2.865,3.287 0.156,0.198 10 D 4.407,2.349 4.564,2.547 0.156,0.198 10 E 6.001,4.786 6.157,4.984 0.156,0.198 10 H 3.627,9.021 3.783,9.219 0.156,0.198 10 G 3.114,6.084 3.27,6.282 0.156,0.198 10 F

Mark Front Race Diameter
Inside / Outside mm (in.)
Thrust Bearing Diameter
Inside / Outside mm (in.)
Rear Race Diameter
Inside / Outside mm (in.)
A - 57.7 (2.27) / 75.2 (2.96) -
B - 29.1 (1.15) / 48.6 (1.91) 30.7 (1.21) / 48.3 (1.90)
C 65.9 (2.59) / 80.3 (3.16) 62.6 (2.47) / 82.4 (3.24) -
D 59.4 (2.34) / 77 (3.03) 53.1 (2.09) / 79 (3.11) -
E - 56.1 (2.21) / 80.9 (3.19) -
F - 61.2 (2.41) / 79 (3.11) -
G - 28 (1.10) / 47.1 (1.85) 26.1 (1.03) / 44 (1.73)
H 52.2 (2.06) / 70.4 (2.77) 48.9 (1.93) / 72.0 (2.84) -


Hide 35782E 2.INSTALL COUNTER DRIVE GEAR BEARING

NOTICE:

Perform this procedure only when replacement of the counter drive gear bearing or transaxle case sub-assembly is necessary.


a.
C138721N09
1.594,1.01 2.375,0.906 2.375,0.906 1.76,1.188 false 2.167,2.396 2.729,1.656 2.729,1.656 1.833,2.135 false 2.417,0.813 2.76,0.979 0.344,0.167 10 false SST 2.802,1.49 3.146,1.656 0.344,0.167 10 false SST

Using SST and a press, install a new counter drive gear bearing (outer race) and snap ring to the transaxle case sub-assembly.

SST
09950-60020  (09951-01030)
09950-70010  (09951-07100)


Hide 3.INSTALL COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING OUTER RACE

a.
C194899N01
2.26,0.375 2.177,0.375 2.177,0.375 2.208,0.708 false 1.292,2.208 1.052,2.552 1.052,2.552 1.188,2.542 false 1.885,0.323 2.354,0.594 0.469,0.271 10 false SST 0.688,2.479 1,2.677 0.313,0.198 10 true SST

Using SST and a hammer, install a new counter driven gear rear tapered roller bearing outer race to the transaxle case sub-assembly.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07100)

NOTICE:

Make sure to install the counter driven gear rear tapered roller bearing outer race so that there is no clearance between the counter driven gear rear tapered roller bearing outer race and transaxle case sub-assembly. If there is any clearance, the turning torque of the counter driven gear cannot be measured correctly.



Hide 4.INSTALL COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING OUTER RACE

a.
C194900N02
2.375,0.313 2.229,0.313 2.229,0.313 2.292,0.573 false 1.469,2.552 0.865,2.688 0.865,2.688 1.583,2.26 false 1.865,0.281 2.281,0.521 0.417,0.24 10 false SST 0.5,2.604 0.813,2.771 0.313,0.167 10 false SST

Install the shim to the transaxle housing.


b.

Using SST, install a new counter driven gear front tapered roller bearing outer race to the transaxle housing.

SST
09950-60020  (09951-00810)
09950-70010  (09951-07100)

NOTICE:

Make sure to install the counter driven gear front tapered roller bearing outer race so that there is no clearance between the counter driven gear front tapered roller bearing outer race and transaxle case sub-assembly. If there is any clearance, the turning torque of the counter driven gear cannot be measured correctly.



Hide 5.INSTALL COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING

a.
C194897N03
0.594,0.771 0.677,0.771 0.677,0.771 0.813,1.156 false 2.281,0.833 2.458,0.833 false 0.24,0.688 0.563,0.854 0.323,0.167 10 false SST 1.938,0.75 2.26,0.917 0.323,0.167 10 false SST

Using SST and a press, install a new counter driven gear rear tapered roller bearing to the counter driven gear.

SST
09950-60010  (09951-00420)

NOTICE:

Make sure to install the counter driven gear rear tapered roller bearing so that there is no clearance between the counter driven gear rear tapered roller bearing and transaxle case sub-assembly. If there is any clearance, the turning torque of the counter driven gear cannot be measured correctly.



Hide 6.INSTALL COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING

a.
C194896N02
0.604,0.615 0.688,0.615 0.688,0.615 0.792,0.99 false 2.396,0.667 2.51,0.667 false 0.24,0.531 0.563,0.708 0.323,0.177 10 false SST 2.073,0.594 2.458,0.792 0.385,0.198 10 false SST

Using SST and a press, install a new counter driven gear front tapered roller bearing to the counter driven gear.

SST
09950-60010  (09951-00530)

NOTICE:

Make sure to install the counter driven gear front tapered roller bearing so that there is no clearance between the counter driven gear front tapered roller bearing and transaxle case sub-assembly. If there is any clearance, the turning torque of the counter driven gear cannot be measured correctly.



Hide 7.ADJUST COUNTER DRIVEN GEAR PRELOAD

a.

Remove any remaining seal packing from the contact surfaces of the transaxle housing and transaxle case sub-assembly.


b.
C317767

Install the counter driven gear to the transaxle case sub-assembly.


c.
C317768

Install the front differential case to the transaxle case sub-assembly.


d.
C136447N03
1.51,1.615 2.49,1.958 2.49,1.958 2.219,1.656 false 1.906,1.646 2.49,1.958 false 2.583,0.917 3.063,1.104 3.063,1.104 2.49,1.417 false 3.063,1.104 2.615,1.146 false 2.031,0.604 2.896,0.188 2.896,0.188 2.302,0.74 false 1.792,0.5 2.875,0.198 false 1.354,0.438 0.552,0.271 0.552,0.271 0.844,0.719 false 1.146,0.51 0.552,0.271 0.552,0.271 1.021,0.615 false 0.594,1.021 0.229,1.354 0.229,1.354 0.677,1.604 false 0.573,1.396 0.24,1.354 0.24,1.354 0.542,1.198 false 1.292,1.74 0.865,2.01 0.865,2.01 0.885,1.781 false 0.865,2.01 1.083,1.823 false 2.917,0.094 3.052,0.25 0.135,0.156 10 false A 2.5,1.865 2.635,2.021 0.135,0.156 10 false B 0.385,0.156 0.521,0.313 0.135,0.156 10 false A 3.083,1.031 3.219,1.188 0.135,0.156 10 false A 0.729,1.969 0.865,2.125 0.135,0.156 10 false A 0.083,1.271 0.219,1.427 0.135,0.156 10 false A

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
Bolt (A) : 31 N*m (316 kgf*cm, 23 ft.*lbf)
Bolt (B) : 23 N*m (234 kgf*cm, 17 ft.*lbf)


e.
C317726N02
1.406,4.344 1.281,4.344 1.281,4.344 1.031,3.385 false 1.49,4.271 1.906,4.49 0.417,0.219 10 false SST

Using SST and a torque wrench, measure the turning torque of the counter driven gear while rotating SST at 10 rpm.

SST
09564-33010  

Turning Torque:

Differential side bearing preload + 3.2 to 5.7 N*m (33 to 58 kgf*cm, 29 to 50 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim for the counter driven gear front tapered roller bearing outer race so that the turning torque is within the specified range.

Shim Thickness: mm (in.)
Thickness Thickness Thickness Thickness
2.000 (0.0787) 2.275 (0.0896) 2.525 (0.0994) 2.775 (0.109)
2.025 (0.0797) 2.300 (0.0906) 2.550 (0.100) 2.800 (0.110)
2.050 (0.0807) 2.325 (0.0915) 2.575 (0.101) 2.825 (0.111)
2.075 (0.0817) 2.350 (0.0925) 2.600 (0.102) 2.850 (0.112)
2.100 (0.0827) 2.375 (0.0935) 2.625 (0.103) 2.875 (0.113)
2.125 (0.0837) 2.400 (0.0945) 2.650 (0.104) 2.900 (0.114)
2.150 (0.0846) 2.425 (0.0955) 2.675 (0.105) 2.925 (0.115)
2.175 (0.0856) 2.450 (0.0965) 2.700 (0.106) 2.950 (0.116)
2.200 (0.0866) 2.475 (0.0974) 2.725 (0.107) 2.975 (0.117)
2.225 (0.0876) 2.500 (0.0984) 2.750 (0.108) 3.000 (0.118)
2.250 (0.0886) - - -


f.

Remove the 20 bolts and transaxle housing.


g.

Remove the front differential case from the transaxle case sub-assembly.


h.

Remove the counter driven gear from the transaxle case sub-assembly.


Hide 35506F 8.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C188148N04
1.24,1.979 0.969,1.979 0.969,1.979 1.219,2.26 false 1.813,1.375 2.208,1.375 2.208,1.375 1.813,0.99 false 0.625,1.885 0.938,2.042 0.313,0.156 10 false SST 2.26,1.281 2.573,1.438 0.313,0.156 10 true SST

Coat the lip of a new manual valve lever shaft oil seal with MP grease.


b.

Using SST and a hammer, install the manual valve lever shaft oil seal to the transaxle case sub-assembly.

SST
09950-60010  (09951-00230)
09950-70010  (09951-07100)

Oil seal driven in depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



Hide 35561 9.INSTALL MANUAL VALVE LEVER SHAFT

a.

Install a new spacer to the parking lock lever sub-assembly.


b.

Install the parking lock lever sub-assembly to the manual valve lever shaft.


c.

Install a new spacer to the manual valve lever sub-assembly.


d.

Install the manual valve lever sub-assembly to the manual valve lever shaft.


e.
C137428

Install the manual valve lever shaft to the transaxle case sub-assembly.

NOTICE:

Do not damage the manual valve lever shaft oil seal while installing the manual valve lever shaft to the transaxle case sub-assembly.



f.
C137417

Using a pin punch (3 mm) and hammer, install a new slotted spring pin into the parking lock lever sub-assembly.


g.
C137429

Turn the spacer and the lever shaft to align the smaller hole of the spacer with the staking position mark on the manual valve lever shaft.


h.

Using a pin punch, stake the spacer through the small hole.


i.

Check that the spacer does not turn.


j.
C136702

Using a pin punch (3 mm) and hammer, install a new slotted spring pin into the manual valve lever sub-assembly.


k.
C137430

Turn the spacer and the lever shaft to align the smaller hole of the spacer with the staking position mark on the manual valve lever shaft.


l.

Using a pin punch, stake the spacer through the small hole.


m.

Check that the spacer does not turn.


n.
C287972

Using needle-nose pliers, install the manual valve shaft retainer spring to the transaxle case sub-assembly.


Hide 35501 10.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

a.
C136683

Align the slot with the notches on the parking lock lever sub-assembly and install the parking lock rod sub-assembly.


Hide 35409 11.INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY

a.
C287971

Install the manual detent spring sub-assembly and cover to the transaxle case sub-assembly with the bolt.

Torque:
23 N*m (234 kgf*cm, 17 ft.*lbf)

NOTICE:

Make sure to install the manual detent spring first and then the cover.



Hide 35623 12.INSTALL NO. 3 BRAKE PISTON

a.
C137432

Coat the contact surface of the transaxle case sub-assembly with ATF.


b.

Coat the lip of the No. 3 brake piston with ATF.


c.
C137431

Temporarily install the pawl stopper plate to the transaxle case sub-assembly with the 2 bolts.


d.
C141536C02
2.326,0.224 2.5,0.415 0.174,0.192 10 *1 2.488,1.954 2.681,2.121 0.193,0.167 10 *2 0.716,0.065 0.897,0.244 0.181,0.179 10 *2 0.817,1.784 2.305,0.357 2.305,0.357 2.046,0.914 false 0.961,0.145 1.24,0.145 1.24,0.145 0.745,1.436 false 2.294,2.153 2.458,2.048 false
*1 Brake Piston Return Spring
*2 No. 3 Brake Piston


Press the No. 3 brake piston into the transaxle case sub-assembly.

NOTICE:
·

Make sure that the lip of the No. 3 brake piston is not twisted and does not get caught in the transaxle case sub-assembly.

·

After installation, make sure that the protrusions on the No. 3 brake piston and the grooves on the pawl stopper plate are aligned.



HINT:

Use the installation surface of the return spring to press the piston into the transaxle case sub-assembly.



e.

Install the return spring to the transaxle case sub-assembly.


f.
C287974

Remove the 2 bolts and pawl stopper plate from the transaxle case sub-assembly.


g.
C274818N01
1.146,1.531 0.615,0.708 true 0.333,0.583 0.792,0.781 0.458,0.198 10 SST

Place SST on the brake piston return spring and compress the brake piston return spring using a press.

SST
09387-00070  

NOTICE:

Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.



h.

Using a screwdriver, install the snap ring to the transaxle case sub-assembly as shown in the illustration.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.

·

Be sure to align the opening of the snap ring with one of the protrusions on the brake piston return spring as shown in the illustration.




Hide 35782C 13.INSTALL COUNTER DRIVE GEAR

a.

Install 2 new balls of the counter drive gear bearing to the counter drive gear bearing.


b.
C274819N01
1.677,1.396 0.917,1.823 0.917,1.823 1.75,1.156 true 1.24,3.219 0.781,3.073 0.781,3.073 1.302,2.917 false 1.208,4.156 0.688,3.979 0.688,3.979 1.219,3.979 false 0.615,1.75 1.073,1.948 0.458,0.198 10 SST 0.469,3 0.927,3.198 0.458,0.198 10 SST 0.385,3.906 0.844,4.104 0.458,0.198 10 SST

Using SST, install the counter drive gear, a new bearing inner race (front side) and bearing inner race (rear side) to the transaxle case sub-assembly.

SST
09223-15030  
09527-17011  
09950-70010  (09951-07100)
09950-60020  (09951-00810)

NOTICE:

There should not be any clearance between the bearing inner race (front side) and counter drive gear.



Hide 35720 14.INSTALL FRONT PLANETARY GEAR ASSEMBLY

a.
C274820N01
1.646,0.865 2.333,0.531 true 1.615,2.677 1.917,2.677 false 1.677,3.885 2,4.073 2,4.073 1.656,4.073 false 2.385,0.438 2.844,0.635 0.458,0.198 10 SST 1.969,2.604 2.427,2.802 0.458,0.198 10 SST 2.042,4.01 2.5,4.208 0.458,0.198 10 SST

Using SST and a press, press the planetary gear assembly onto the transaxle case sub-assembly.

SST
09223-15030  
09527-17011  
09951-01100  


Hide 35622G 15.INSTALL NO. 2 BRAKE PISTON

a.
C136673C04
2.01,0.552 2.594,0.552 false 1.344,1.208 0.885,1.208 false 0.688,1.115 0.844,1.302 0.156,0.188 10 false *1 2.646,0.479 2.802,0.667 0.156,0.188 10 false *1
*1 O-ring


Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.

NOTICE:

Ensure that the 2 O-rings are not twisted.



b.
C138726

Install the No. 2 brake piston to the transaxle case sub-assembly.

NOTICE:

Be careful not to damage the O-rings.



Hide 35068C 16.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.

Install the 1st and reverse brake return spring to the transaxle case sub-assembly.


b.

Place SST on the 1st and reverse brake return spring and compress the 1st and reverse brake return spring using a press.

C274821N01
0.823,1.604 1.354,1.177 false 2.25,2.406 2.438,2.26 false 0.552,1.604 1.01,1.802 0.458,0.198 10 SST 2.479,2.177 2.938,2.375 0.458,0.198 10 SST

SST
09387-00060  

NOTICE:

Stop the press when the 1st and reverse brake return spring is flush with the snap ring groove. This prevents the 1st and reverse brake return spring from being deformed.



c.

Using a screwdriver, install the snap ring to the transaxle case sub-assembly as shown in the illustration.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.

·

Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case sub-assembly as shown in the illustration.




Hide 35682A 17.INSTALL NO. 2 BRAKE DISC

a.
C136483C04
2.502,1.086 2.668,1.266 0.166,0.18 10 *3 0.891,1.185 1.051,1.365 0.16,0.18 10 *2 2.357,0.435 2.521,0.615 0.164,0.18 10 *1 1.31,0.87 1.213,0.87 1.213,0.87 1.213,1.702 false 1.213,1.702 1.31,1.702 false 1.31,1.069 1.213,1.069 false 1.32,1.475 1.213,1.475 false 1.31,1.268 1.105,1.268 false 2.166,0.542 2.305,0.542 false 2.213,0.781 2.364,0.781 2.364,0.781 2.364,1.598 false 2.364,1.598 2.206,1.598 false 2.213,0.985 2.364,0.985 false 2.212,1.403 2.364,1.403 false 2.213,1.184 2.451,1.184 false
*1 Brake Flange
*2 Brake Plate
*3 Brake Disc


Install the 5 brake discs, 5 brake plates and brake flange to the transaxle case sub-assembly.

NOTICE:

Make sure that the discs, plates and flange are installed in the correct order.



b.
C136481

Using a screwdriver, install the snap ring to the transaxle case sub-assembly.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.

·

Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case sub-assembly as shown in the illustration.




Hide 35762E 19.INSTALL PLANETARY RING GEAR FLANGE

a.
C136480C09
1.271,0.646 0.969,0.646 false 0.958,2.302 1.219,2.302 false 2.073,1.302 2.385,1.302 false 0.719,2.229 0.896,2.396 0.177,0.167 10 false *3 2.458,1.24 3.146,1.625 0.688,0.385 10 false *2 0.719,0.573 0.896,0.74 0.177,0.167 10 false *1
*1 Snap Ring
*2 Planetary Ring Gear Flange
*3 Planetary Ring Gear


Install the planetary ring gear flange to the planetary ring gear.


b.

Using a screwdriver, install the snap ring to the planetary ring gear.

NOTICE:

Confirm that the snap ring is correctly located in the groove of the planetary ring gear.



Hide 35743K 20.INSTALL PLANETARY RING GEAR

a.
C136479C04
0.948,0.49 1.229,0.49 false 1.969,1.302 2.344,1.302 false 0.708,0.396 0.885,0.573 0.177,0.177 10 false *1 2.406,1.26 2.76,1.51 0.354,0.25 10 false *2
*1 One-way Clutch Assembly
*2 Planetary Ring Gear


Install the planetary ring gear to the one-way clutch assembly.

NOTICE:

Make sure that the one-way clutch assembly is positioned in the correct direction as shown in the illustration.



Hide 35790 21.INSTALL ONE-WAY CLUTCH ASSEMBLY

a.
C274822C01
1.26,2.604 1.479,2.063 1.479,2.063 1.667,2.063 false 0.688,3.417 1.052,2.938 false 1.719,2.01 2.031,2.208 0.313,0.198 10 *1 0.583,3.438 0.896,3.635 0.313,0.198 10 *2
*1 One-way Clutch Assembly
*2 Thrust Needle Roller Bearing


Coat the thrust needle roller bearing with ATF, and install it onto the planetary gear assembly.

Bearing Diameter: mm (in.)
- Inside Outside
Bearing 56.1 (2.21) 80.9 (3.19)

NOTICE:

Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



b.

Install the one-way clutch assembly to the transaxle case sub-assembly.

NOTICE:

Make sure that there is no clearance between the retainer and the claw on the one-way clutch assembly. If there is any clearance, the spring of the retainer will be deformed.



c.
C136477

Using a screwdriver, install the snap ring to the transaxle case sub-assembly.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.

·

Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case sub-assembly as shown in the illustration.




Hide 35557 22.INSTALL PARKING LOCK PAWL

a.
C136475C04
1.542,0.313 1.333,0.313 1.333,0.313 1.156,1.292 false 0.885,0.271 0.698,0.271 0.698,0.271 0.458,1.615 false 0.458,2.802 0.458,2.625 0.458,2.625 1.052,2.458 false 1.531,2.698 0.771,3.021 0.771,3.021 0.771,3.167 false 0.365,2.844 0.542,3.021 0.177,0.177 10 false *3 0.698,3.208 1.063,3.375 0.365,0.167 10 false *4 0.948,0.188 1.115,0.354 0.167,0.167 10 false *1 1.646,0.229 1.969,0.427 0.323,0.198 10 true *2
*1 Parking Lock Pawl Shaft
*2 Parking Lock Pawl
*3 Spring
*4 Parking Lock Pawl Pin


Install the parking lock pawl to the transaxle case sub-assembly with the parking lock pawl shaft.


b.

Install the parking lock pawl pin to the transaxle case sub-assembly.


c.
C137444

Install the spring to the parking lock pawl.

NOTICE:

Make sure that one end of the spring is set in the hole of the transaxle case sub-assembly and the other end is positioned on the parking lock pawl as shown in the illustration.



Hide 35598 23.INSTALL PARKING LOCK SLEEVE

a.
C136474

Install the parking lock sleeve to the transaxle case sub-assembly.


Hide 35596 24.INSTALL PAWL STOPPER PLATE

a.
C136473

Install the pawl stopper plate to the transaxle case sub-assembly with the 2 bolts.

Torque:
23 N*m (234 kgf*cm, 17 ft.*lbf)


Hide 35558 25.INSTALL PAWL SHAFT CLAMP

a.
C136472

Install the pawl shaft clamp to the transaxle case sub-assembly with the bolt.

Torque:
23 N*m (234 kgf*cm, 17 ft.*lbf)


Hide 35783R 26.INSTALL COUNTER DRIVEN GEAR

a.
C136469

Install the counter driven gear sub-assembly to the transaxle case sub-assembly.


Hide 35782H 27.INSTALL COUNTER DRIVE GEAR NUT

a.
C136700N04
1.542,4.042 1.906,4.313 0.365,0.271 10 false P

Turn the manual valve lever shaft sub-assembly 2 notches counterclockwise to set it to the P position as shown in the illustration.


b.
C202887N01
0.719,2.75 0.865,2.75 0.865,2.75 1.583,1.833 true 0.417,2.688 0.76,2.906 0.344,0.219 10 false SST

Using SST, install a new counter drive gear nut.

SST
09387-00130  

Torque:
120 N*m (1223 kgf*cm, 88 ft.*lbf)


c.
C136699N04
1.531,3.99 1.958,4.229 0.427,0.24 10 false N

Turn the manual valve lever shaft sub-assembly 2 notches clockwise to set it to the N position as shown in the illustration.


d.

Remove the counter driven gear from the transaxle case sub-assembly.


e.
C319474N01
0.719,2.906 0.854,2.906 0.854,2.906 1.573,1.833 true 0.406,2.854 0.813,3.125 0.406,0.271 10 false SST

Using SST and a torque wrench, measure the turning torque of the bearing while rotating SST at 60 rpm.

SST
09387-00130  

Turning Torque:

0.1 to 0.2 N*m (1 to 2 kgf*cm, 0.9 to 1.9 in.*lbf)


If the measured value is not within the specified range, gradually tighten the counter drive gear nut until the turning falls within the specified range.

Maximum Torque:

180 N*m (1835 kgf*cm, 132 ft.*lbf)



f.
C136698N04
0.823,0.341 1.162,0.523 0.339,0.183 10 SST 1.587,0.697 1.201,0.434 false

Using SST and a hammer, stake the front planetary gear assembly.

SST
09930-00010  


g.

Install the counter driven gear to the transaxle case sub-assembly.


Hide 28.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

Hide 41311 29.INSTALL FRONT DIFFERENTIAL CASE

a.
C136467

Install the front differential case to the transaxle case sub-assembly.


Hide 35621F 30.INSTALL NO. 1 BRAKE PISTON

a.
C136466C04
1.969,0.656 2.365,0.656 false 1.365,0.667 0.917,0.667 false 2.438,0.615 2.781,0.823 0.344,0.208 10 false *1 0.708,0.573 1.146,0.885 0.438,0.313 10 false *1
*1 O-ring


Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.

NOTICE:

Ensure that the O-rings are not twisted.



b.
C138253

Install the No. 1 brake piston to the oil pump assembly.

NOTICE:

Be careful not to damage the O-rings.



Hide 35608L 31.INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C136464

Install the 3 2nd brake piston return springs to the oil pump assembly.

NOTICE:

Make sure that the 3 2nd brake piston return springs are installed onto the protrusions on the oil pump assembly.



Hide 32.INSTALL NO. 1 BRAKE DISC

a.
C141545C02
1.927,1.198 1.615,1.198 false 1.917,2.594 1.802,2.594 1.802,2.594 1.802,1.198 false 1.927,2.083 1.802,2.083 false 1.938,1.677 1.813,1.677 false 2.771,1.375 2.938,1.375 false 2.76,0.979 2.833,0.979 2.833,0.979 2.833,2.365 false 2.833,2.365 2.76,2.365 false 2.76,1.865 2.833,1.865 false 1.646,0.104 1.781,0.104 1.781,0.104 2.063,0.458 false 1.448,0.052 1.625,0.229 0.177,0.177 10 false *1 1.427,1.104 1.792,1.365 0.365,0.26 10 false *2 2.99,1.313 3.219,1.531 0.229,0.219 10 false *3
*1 No. 1 Brake Flange
*2 No. 1 Brake Plate
*3 No. 1 Brake Disc


Install the 4 No. 1 brake discs, 4 No. 1 brake plates and No. 1 brake flange to the front oil pump assembly.

NOTICE:
·

Make sure that the discs, plates, and flange are installed in the correct order.

·

Be sure to install the flange in the correct direction.




b.

Place SST on the flange and compress the flange using a press.

SST
09387-00070  
09495-65040  

NOTICE:

Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.



c.
C189783N07
1.885,0.75 2.5,0.25 2.5,0.25 2.198,1.01 false 0.99,3.146 0.49,3.146 false 2.531,0.156 2.844,0.302 0.313,0.146 10 false SST 0.125,3.042 0.438,3.219 0.313,0.177 10 false (#1)

Using a screwdriver, install the snap ring to the front oil pump assembly as shown in the illustration (#1).

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the front oil pump assembly.

·

Make sure to align the protruding part of the snap ring with the indented part (#1) of the front oil pump assembly shown in the illustration to install the snap ring.




d.
C176220

Install the brake snap ring stopper to the front oil pump assembly.

NOTICE:

Be sure to install the brake snap ring stopper in the correct direction.



e.
C189784N02
1.906,0.75 2.458,0.188 2.458,0.188 2.188,1.094 false 2.563,3.323 2.917,3.323 false 2.5,0.094 2.802,0.26 0.302,0.167 10 false SST 2.927,3.229 3.198,3.406 0.271,0.177 10 false (#2)

Using a screwdriver, install the snap ring to the front oil pump assembly as shown in the illustration (#2).

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the front oil pump assembly.

·

Make sure to align the protruding part of the snap ring with the indented part (#2) of the front oil pump assembly shown in the illustration to install the snap ring.




f.
C153481C05
0.942,2.568 1.127,2.736 0.185,0.168 10 *2 1.961,0.463 2.142,0.63 0.181,0.167 10 *1 0.112,0.054 0.3,0.209 0.187,0.155 10 *a 1.681,2.118 1.302,2.651 1.302,2.651 1.166,2.651 false 1.5,1.724 1.5,0.55 1.5,0.55 1.931,0.55 false 1.763,1.714 1.763,0.55 false
*1 Snap Ring
*2 Brake Snap Ring Stopper
*a Correctly installed


Check that the brake snap ring stopper can be turned by hand.

NOTICE:

If the brake snap ring stopper cannot be turned by hand, the brake snap ring stopper may have been installed upside down, or the snap ring may not have been completely located in the groove on the front oil pump assembly. Remove and reinstall the snap ring and the brake snap ring stopper.



Hide 34321 34.INSTALL UNDERDRIVE PLANETARY SUN GEAR

a.
C141538C02
1.604,0.552 1.302,0.552 false 2.521,1.281 2.219,1.281 false 1.104,0.448 1.26,0.635 0.156,0.188 10 false *2 2.573,1.188 3.063,1.458 0.49,0.271 10 false *1
*1 Thrust Needle Roller Bearing
*2 Underdrive Planetary Sun Gear


Coat the thrust needle roller bearing with ATF, and install it to the front oil pump assembly.

Bearing Diameter: mm (in.)
- Inside Outside
Bearing 57.7 (2.27) 75.2 (2.96)

NOTICE:

Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



b.

Install the underdrive planetary sun gear to the oil pump assembly.


Hide 35701 35.INSTALL INPUT SHAFT SUB-ASSEMBLY

a.
C141539C03
2.201,2.569 2.388,2.758 0.187,0.189 10 *3 1.679,2.821 2.186,2.662 2.186,2.662 1.696,3.132 false 1.696,2.994 2.186,2.662 false 0.688,0.471 2.17,0.13 2.17,0.13 1.746,0.436 false 2.195,0.041 2.369,0.235 0.175,0.194 10 *1 0.833,0.807 0.603,1.421 0.603,1.421 1.315,1.028 false 0.476,1.455 0.658,1.657 0.183,0.201 10 *2 2.187,1.673 2.364,1.863 0.178,0.19 10 *4 1.681,1.777 2.142,1.777 false
*1 Thrust Needle Roller Race
*2 Thrust Needle Roller Bearing
*3 Input Shaft Oil Seal Ring
*4 Input Shaft


Coat 3 new input shaft oil seal rings with ATF and install them to the input shaft.

NOTICE:

Do not expand the gap of the oil seal ring excessively.



b.

Coat the thrust needle roller bearing and thrust needle roller race with ATF, and install them on the front oil pump assembly.

Bearing and Race Diameter: mm (in.)
- Inside Outside
Bearing 29.1 (1.15) 48.6 (1.91)
Race 30.7 (1.21) 48.3 (1.90)

NOTICE:

Be sure to install the thrust needle roller bearing in the correct direction.



c.
C136459

Install the input shaft to the front oil pump assembly.


Hide 35706V 36.INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C136457C04
0.881,2.843 1.06,2.99 0.18,0.146 10 *3 1.453,2.916 1.113,2.916 false 1.019,0.355 1.184,0.505 0.165,0.15 10 *1 2.536,1.623 2.721,1.781 0.184,0.158 10 *2 1.242,0.443 1.41,0.443 false 2.492,1.708 2.202,1.708 false
*1 Planetary Sun Gear Sub-assembly
*2 Underdrive Planetary Gear Assembly
*3 Snap Ring


Using a snap ring expander, install the snap ring to the underdrive planetary gear assembly.


b.

Using a snap ring expander, install the planetary sun gear sub-assembly to the underdrive planetary gear assembly with the snap ring expanded.


Hide 34341 37.INSTALL UNDERDRIVE PLANETARY RING GEAR

a.
C136456C04
2.083,0.396 2.365,0.396 false 1.344,0.792 1.021,0.792 false 2.448,0.333 2.781,0.615 0.333,0.281 10 false *1 0.781,0.708 0.948,0.875 0.167,0.167 10 false *2
*1 Snap Ring
*2 Underdrive Planetary Ring Gear


Install the underdrive planetary ring gear to the underdrive planetary gear assembly.


b.

Using needle-nose pliers, install the snap ring to the underdrive planetary ring gear.

NOTICE:

Confirm that the snap ring is correctly located in the groove of the underdrive planetary ring gear.



Hide 35663 38.INSTALL NO. 3 BRAKE HUB

a.
C141540C02
1.979,0.688 2.208,0.688 false 2.281,0.625 2.698,0.969 0.417,0.344 10 false *1
*1 Thrust Needle Roller Bearing


Coat the thrust needle roller bearing with ATF and install it on the underdrive planetary gear assembly.

Bearing and Race Diameter: mm (in.)
- Inside Outside
Bearing 62.6 (2.46) 82.9 (3.26)
Race 65.9 (2.59) 80.3 (3.16)

NOTICE:

Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



b.
C141537C02
2.295,1.716 2.471,1.885 0.176,0.169 10 *1 2.078,1.687 2.261,1.779 false
*1 Thrust Needle Roller Race


Coat the thrust needle roller race with MP grease and install it to the No. 3 brake hub.


c.
C136454

Install the No. 3 brake hub to the underdrive planetary gear assembly.


Hide 34330 39.INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C136458

Install the underdrive planetary gear assembly to the front oil pump assembly.


Hide 35683B 40.INSTALL NO. 3 BRAKE DISC

a.
C136452C09
1.948,0.25 2.219,0.25 false 2.146,1.25 2.292,1.25 false 2.156,0.719 2.229,0.719 2.229,0.719 2.229,1.635 false 2.229,1.635 2.156,1.635 false 1.177,1.99 1.323,1.99 false 1.313,0.938 1.125,0.938 false 1.313,1.438 1.229,1.438 1.229,1.438 1.229,0.938 false 2.281,0.188 2.635,0.438 0.354,0.25 10 false *1 2.354,1.156 2.521,1.333 0.167,0.177 10 false *3 0.917,0.854 1.094,1.031 0.177,0.177 10 false *2 0.979,1.896 1.146,2.083 0.167,0.188 10 false *1
*1 No. 3 Brake Flange
*2 No. 3 Brake Plate
*3 No. 3 Brake Disc


Install the 2 No. 3 brake flanges, 3 No. 3 brake discs and 2 No. 3 brake plates to the front oil pump assembly.

NOTICE:

Make sure that the discs, plates and flanges are installed in the correct order.



b.
C274824N02
2.271,0.854 2.667,0.354 2.667,0.354 1.344,0.448 true 2.708,0.271 3.167,0.469 0.458,0.198 10 (A)

Using a screwdriver, install the snap ring to the front oil pump assembly.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the front oil pump assembly.

·

Make sure that the snap ring ends are positioned as shown in the illustration (A).




Hide 35035 42.INSTALL FRONT OIL PUMP ASSEMBLY

a.
C141541C02
1.385,1.24 0.823,0.781 false 1.385,1.833 0.969,1.594 false 2.156,2.531 2.479,2.625 false 0.615,0.646 1.104,0.875 0.49,0.229 10 false *2 0.74,1.49 0.906,1.677 0.167,0.188 10 false *1 2.552,2.583 2.875,2.906 0.323,0.323 10 false *3
*1 Thrust Needle Roller Bearing
*2 Thrust Needle Roller Race
*3 O-ring


Coat a new O-ring with ATF and install it to the transaxle case sub-assembly.


b.

Coat the thrust needle roller bearing and thrust needle roller race with ATF and install them on the underdrive planetary gear assembly.

Bearing and Race Diameter: mm (in.)
- Inside Outside
Bearing 53.1 (2.09) 79 (3.11)
Race 59.4 (2.34) 77 (3.03)

NOTICE:

Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



c.
C287970C01
2.365,0.188 2.76,0.188 false 2.896,0.135 3.208,0.333 0.313,0.198 10 false *1
*1 O-ring


Coat a new O-ring with ATF and install it to the front oil pump assembly.


d.

Install the front oil pump assembly to the transaxle case sub-assembly with the 7 bolts.

Torque:
23 N*m (234 kgf*cm, 17 ft.*lbf)


Hide 35301B 43.INSTALL FRONT OIL PUMP BODY O-RING

a.
C138278

Coat a new O-ring with ATF and install it to the front oil pump body sub-assembly.


Hide 35882A 44.INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C287969

Install the differential gear lube apply tube to the transaxle housing.

NOTICE:

Insert the differential gear lube apply tube into the transaxle case sub-assembly until it makes contact with the stopper.



b.

Install the clamp to the differential gear lube apply tube with the bolt.

Torque:
23 N*m (234 kgf*cm, 17 ft.*lbf)

NOTICE:

There should be clearance between the differential lube apply tube and clamp.



Hide 35111C 45.INSTALL TRANSAXLE HOUSING

a.

Remove any packing material from the contact surfaces between the transaxle housing and case.

NOTICE:

Make sure that there is no ATF on the contact surfaces.



b.
C138263C02
2.802,0.26 2.646,0.26 2.646,0.26 2.396,0.479 false 2.875,0.188 3.031,0.344 0.156,0.156 10 false *a
*a FIPG


Apply FIPG to the transaxle case sub-assembly.

FIPG:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Apply FIPG in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.



c.
C136447N03
1.51,1.615 2.49,1.958 2.49,1.958 2.219,1.656 false 1.906,1.646 2.49,1.958 false 2.583,0.917 3.063,1.104 3.063,1.104 2.49,1.417 false 3.063,1.104 2.615,1.146 false 2.031,0.604 2.896,0.188 2.896,0.188 2.302,0.74 false 1.792,0.5 2.875,0.198 false 1.354,0.438 0.552,0.271 0.552,0.271 0.844,0.719 false 1.146,0.51 0.552,0.271 0.552,0.271 1.021,0.615 false 0.594,1.021 0.229,1.354 0.229,1.354 0.677,1.604 false 0.573,1.396 0.24,1.354 0.24,1.354 0.542,1.198 false 1.292,1.74 0.865,2.01 0.865,2.01 0.885,1.781 false 0.865,2.01 1.083,1.823 false 2.917,0.094 3.052,0.25 0.135,0.156 10 false A 2.5,1.865 2.635,2.021 0.135,0.156 10 false B 0.385,0.156 0.521,0.313 0.135,0.156 10 false A 3.083,1.031 3.219,1.188 0.135,0.156 10 false A 0.729,1.969 0.865,2.125 0.135,0.156 10 false A 0.083,1.271 0.219,1.427 0.135,0.156 10 false A

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
Bolt A : 31 N*m (316 kgf*cm, 23 ft.*lbf)
Bolt B : 23 N*m (234 kgf*cm, 17 ft.*lbf)


Hide 46.INSTALL NO. 1 CLUTCH DISC

a.
C136446C04
2.308,0.233 2.46,0.431 0.152,0.197 10 *1 2.435,1.305 2.597,1.502 0.162,0.197 10 *3 0.884,1.119 1.056,1.323 0.172,0.204 10 *2 2.129,0.599 2.286,0.599 2.286,0.599 2.286,1.783 false 2.286,1.783 2.127,1.783 false 1.358,1.201 1.11,1.201 false 2.127,0.987 2.286,0.987 false 2.129,1.376 2.384,1.376 false 2.105,0.314 2.263,0.314 false 1.347,0.785 1.193,0.785 1.193,0.785 1.193,1.991 false 1.193,1.991 1.347,1.991 false 1.341,1.552 1.193,1.552 false
*1 Clutch Flange
*2 Clutch Plate
*3 Clutch Disc


Install the clutch flange, 4 clutch discs and 4 clutch plates to the direct multiple disc clutch assembly.

NOTICE:

Make sure that the flange, discs and plates are installed in the correct order.



b.
C136445

Using a screwdriver, install the 2 snap rings to the direct multiple disc clutch assembly.

NOTICE:

Confirm that the snap rings are correctly located in the groove of the direct multiple disc clutch assembly.



Hide 35730 48.INSTALL REAR PLANETARY SUN GEAR ASSEMBLY

a.
C141542C02
1.281,0.813 0.854,0.552 false 1.26,1.469 0.854,1.604 false 0.625,0.458 0.99,0.729 0.365,0.271 10 false *1 0.635,1.563 1.031,1.771 0.396,0.208 10 false *2
*1 Thrust Needle Roller Bearing
*2 Thrust Needle Roller Race


Coat the thrust needle roller bearing and thrust needle roller race with ATF, and install them to the direct multiple disc clutch assembly.

Bearing and Race Diameter: mm (in.)
- Inside Outside
Bearing 28 (1.10) 47.1 (1.85)
Race 26.1 (1.03) 44 (1.73)

NOTICE:

Install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



b.
C136437

Install the rear planetary sun gear assembly to the direct multiple disc clutch assembly.


c.
C136436

Using a snap ring expander, install the snap ring to the direct multiple disc clutch assembly.


Hide 49.INSTALL NO. 2 CLUTCH DISC

a.
C136435C04
2.316,1.634 2.485,1.817 0.17,0.183 10 *3 2.342,0.935 2.514,1.118 0.172,0.183 10 *2 0.867,0.804 1.03,0.986 0.163,0.183 10 *1 2.131,1.705 2.29,1.705 false 2.129,0.634 2.248,0.634 2.248,0.634 2.248,1.437 false 2.248,1.437 2.127,1.437 false 2.129,1.025 2.321,1.025 false 1.36,0.436 1.202,0.436 1.202,0.436 1.202,1.253 false 1.202,1.253 1.357,1.253 false 1.35,0.875 1.06,0.875 false
*1 Clutch Plate
*2 Clutch Disc
*3 Clutch Flange


Install the clutch flange, 3 clutch discs and 3 clutch plates to the direct multiple disc clutch assembly.

NOTICE:

Make sure that the flange, discs and plates are installed in the correct order.



Hide 35635E 50.INSTALL DIRECT MULTIPLE DISC CLUTCH SNAP RING

a.
C136428C04
1.615,0.229 1.281,0.229 false 1.625,1.917 1.438,1.74 1.438,1.74 1.219,1.74 false 1.063,0.156 1.542,0.531 0.479,0.375 10 false *2 1.031,1.656 1.458,1.917 0.427,0.26 10 false *1
*1 Intermediate Shaft Oil Seal
*2 O-ring


Coat a new O-ring with ATF and install it to the direct multiple disc clutch assembly.


b.

Coat a new intermediate shaft oil seal with ATF and install it to the direct multiple disc clutch assembly.


c.
C141535

Install the No. 2 direct clutch piston to the direct multiple disc clutch assembly.

NOTICE:

Be sure to engage the claws on the direct multiple disc clutch assembly in the grooves on the No. 2 direct clutch piston.



d.
C274825

Using a screwdriver, install the snap ring to the direct multiple disc clutch assembly.

NOTICE:
·

Position the opening of the snap ring as shown in the illustration.

·

Confirm that the snap ring is correctly located in the groove of the direct multiple disc clutch assembly.




Hide 35635C 52.INSTALL DIRECT MULTIPLE DISC CLUTCH ASSEMBLY

a.
C141543C02
1.847,1.273 2.345,1.273 false 0.558,2.351 1.056,2.351 false 2.368,1.188 2.529,1.335 0.161,0.147 10 *2 0.36,2.265 0.527,2.419 0.168,0.154 10 *1
*1 Thrust Needle Roller Bearing
*2 Direct Multiple Disc Clutch Assembly


Coat the thrust needle roller bearing with ATF and install it on the transaxle case sub-assembly.

Bearing Diameter: mm (in.)
- Inside Outside
Bearing 61.2 (2.41) 79 (3.11)


b.

Install the direct multiple disc clutch assembly to the transaxle case sub-assembly.


c.

Clean the contact surfaces of the transaxle case sub-assembly and rear transaxle cover sub-assembly.


d.
C138269C02
2.917,0.686 3.066,0.866 0.149,0.179 10 *a
*a Dimension A


As shown in the illustration, place a straightedge on the multiple direct clutch drum and measure the distance between the transaxle case sub-assembly and the straightedge using a vernier caliper (Dimension A).


e.
C138268C05
0.597,0.75 0.766,0.93 0.169,0.179 10 *a
*a Dimension B


Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).


f.

Calculate the end play value using the following formula:

End play = Dimension B - Dimension A - Thrust needle roller bearing thickness

End play:

0.007 to 1.113 mm (0.000275 to 0.0438 in.)



Hide 35102 53.INSTALL REAR TRANSAXLE COVER SUB-ASSEMBLY

a.
C194898N02
2.583,0.865 2.729,0.865 2.729,0.865 2.646,1.063 false 1.177,1.354 1.042,1.354 1.042,1.354 1.177,1.198 false 2.771,0.823 3.083,0.99 0.313,0.167 10 false SST 0.698,1.281 1.01,1.448 0.313,0.167 10 true SST

Using SST and a hammer, install a new needle roller bearing into the rear transaxle cover sub-assembly.

SST
09950-60010  (09951-00220)
09950-70010  (09951-07100)

Installation depth:

21.5 to 21.9 mm (0.846 to 0862 in.)



b.

Apply adhesive to the 2 "TORX" screws.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
C287967

Using a "TORX" socket wrench (T30), install the rear transaxle cover plate to the rear transaxle cover sub-assembly with the 2 "TORX" screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.
C141544C02
1.521,1.344 1.521,0.177 1.521,0.177 1.219,0.177 false 1.333,1.469 1.333,0.177 false 0.688,0.813 0.781,0.813 0.781,0.813 1.021,1.531 false 0.75,2.208 0.531,2.583 false 1.021,0.104 1.177,0.271 0.156,0.167 10 false *1 0.448,0.74 0.688,0.979 0.24,0.24 10 false *2 0.396,2.625 0.729,2.854 0.333,0.229 10 false *3
*1 Oil Seal Ring
*2 Thrust Needle Roller Bearing
*3 Thrust Needle Roller Race


Coat the thrust needle roller bearing and thrust needle roller race with ATF and install them on the transaxle case sub-assembly.

Bearing and Race Diameter: mm (in.)
- Inside Outside
Bearing 48.9 (1.93) 72.0 (2.84)
Race 52.2 (2.06) 70.4 (2.77)


e.

Coat 2 new oil seal rings with ATF and install them to the rear transaxle cover sub-assembly.


f.
C287966

Coat 3 new O-rings with ATF and install them to the transaxle case sub-assembly.

NOTICE:

Ensure that the O-rings are not twisted.



g.
C138271

Remove packing material from the contact surfaces between the rear transaxle cover sub-assembly and transaxle case sub-assembly.

NOTICE:

Make sure that there is no ATF on the contact surfaces.


FIPG:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



h.
C162440N02
2.583,0.927 3.167,1.271 3.167,1.271 2.521,1.75 false 2.448,1.344 3.167,1.271 false 1.813,0.26 2.594,0.063 2.594,0.063 2.49,0.542 false 2.198,0.479 2.583,0.063 2.583,0.063 2.156,0.271 false 0.625,1.635 0.26,0.885 0.26,0.885 1.313,0.24 false 0.885,0.604 0.26,0.885 0.26,0.885 0.792,1.104 false 1.146,1.823 0.969,1.99 false 1.594,1.833 1.594,1.958 false 2.031,1.813 2.188,1.969 false 2.625,0 2.74,0.167 0.115,0.167 10 false A 0.854,1.979 0.979,2.135 0.125,0.156 10 false B 3.188,1.188 3.302,1.354 0.115,0.167 10 false A 0.104,0.781 0.219,0.948 0.115,0.167 10 false A 2.198,1.969 2.323,2.125 0.125,0.156 10 false B 1.521,1.958 1.635,2.125 0.115,0.167 10 false A

Install the rear transaxle cover sub-assembly to the transaxle case sub-assembly with the 14 bolts.

Torque:
Bolt A : 23 N*m (234 kgf*cm, 17 ft.*lbf)
Bolt B : 17 N*m (173 kgf*cm, 12 ft.*lbf)


i.
C162439

Install a new gasket to the refill plug.


j.

Install the refill plug to the rear transaxle cover sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


k.
C134960

Coat 2 new O-rings with ATF and install them to the 2 No. 1 automatic transaxle case plugs.


l.

Install the 2 No. 1 automatic transaxle case plugs to the rear transaxle cover sub-assembly.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 35145C 55.INSTALL TRANSAXLE CASE GASKET

a.
C287964

Coat 2 new gaskets with ATF and install them to the transaxle case sub-assembly.


Hide 35410 56.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C136689N04
2.729,1.594 2.906,2.563 2.906,2.563 2.333,2.177 false 2.01,2.198 1.469,2.854 1.469,2.854 0.854,2.344 false 1.635,2.167 1.469,2.844 1.469,2.844 1.229,2.198 false 2.094,0.948 2.5,0.177 2.5,0.177 2.573,0.177 false 1.333,0.948 1.719,0.219 1.719,0.219 1.781,0.219 false 0.906,0.917 1.188,0.198 1.188,0.198 1.25,0.198 false 0.49,1.354 0.229,0.979 false 0.479,2.052 0.281,2.365 false 0.063,1.917 0.344,2.177 0.281,0.26 10 false *1 3.052,1.479 3.292,1.719 0.24,0.24 10 true *1 2.615,0.094 2.76,0.25 0.146,0.156 10 false A 1.417,2.885 1.781,3.115 0.365,0.229 10 false B 0.083,0.865 0.333,1.083 0.25,0.219 10 false D 1.292,0.104 1.438,0.26 0.146,0.156 10 false C 0.125,2.302 0.271,2.458 0.146,0.156 10 false E 2.906,2.563 3.052,2.719 0.146,0.156 10 false B 1.833,0.135 1.979,0.292 0.146,0.156 10 false B

Install the transmission valve body assembly to the transaxle case sub-assembly with the 11 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

- Bolt Length
Bolt A 25 mm (0.984 in.)
Bolt B 30 mm (1.18 in.)
Bolt C 35 mm (1.38 in.)
Bolt D 45 mm (1.77 in.)
Bolt E 55 mm (2.17 in.)

NOTICE:
·

When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case sub-assembly to interfere with each other.

·

Be sure to insert the pin of the manual valve lever into the groove on the end of the manual valve.

·

First, temporarily tighten the bolts marked by *1 in the illustration because they are positioning bolts.




Hide 35330 57.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.
C136688C06
1.823,0.385 2.063,0.385 false 2.125,0.323 2.448,0.594 0.323,0.271 10 false *1
*1 O-ring


Coat a new O-ring with ATF and install it to the valve body oil strainer assembly.

NOTICE:

Ensure that the O-ring is not twisted or pinched.



b.
C136687

Install the valve body oil strainer assembly to the transmission valve body assembly with the 2 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 35106D 58.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C134963C08
2.906,0.219 1.885,0.219 1.885,0.219 1.885,1.417 false 2.448,1 2.448,0.219 false 2.969,0.135 3.135,0.302 0.167,0.167 10 false *1
*1 Magnet


Install the 2 magnets onto the automatic transaxle oil pan sub-assembly as shown in the illustration.


b.

Install a new gasket to the automatic transaxle oil pan sub-assembly.


c.
C274789

Install the automatic transaxle oil pan sub-assembly to the automatic transaxle assembly with the 17 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:
·

In order to ensure proper sealing of the automatic transaxle oil pan sub-assembly bolts, apply adhesive to the bolts and install them within 10 minutes of adhesive application.

·

Completely remove any oil or grease from the contact surface of the transaxle case sub-assembly and automatic transaxle oil pan sub-assembly with the gasket before installation.




d.
C274790

Clean and degrease the bolt and the installation hole in the automatic transaxle assembly.


e.

Apply adhesive to the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



f.

Install the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


g.
C141531

Using a hexagon socket wrench (6 mm), install the No. 1 oil filler tube to the automatic transaxle oil pan sub-assembly.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


h.
C134961

Using a hexagon socket wrench (6 mm), install the overflow plug and a new gasket to the automatic transaxle oil pan sub-assembly.

Torque:
40 N*m (408 kgf*cm, 29 ft.*lbf)


Hide 35104Q 59.INSTALL NO. 1 TRANSAXLE CASE PLUG

a.

Install 3 new gaskets to the 3 hexagon bolts.


b.

Apply adhesive to the 3 hexagon bolts.

Adhesive:

Toyota Genuine Seal Packing 1344, Three Bond 1344 or equivalent


NOTICE:

In order to ensure proper sealing of the hexagon bolts, apply adhesive to the bolts and install them within 10 minutes of adhesive application.



c.
C134959

Using a hexagon socket wrench (6 mm), install the 3 hexagon bolts to the transaxle housing with the gaskets.

Torque:
17 N*m (173 kgf*cm, 12 ft.*lbf)


d.
C162438

Coat 3 new O-rings with ATF and install them to the 3 No. 1 transaxle case plugs.


e.

Install the 3 No. 1 transaxle case plugs to the transaxle case sub-assembly.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 32921C 60.INSTALL OIL COOLER TUBE UNION (INLET OIL COOLER UNION)

a.
C239679

Coat a new O-ring with ATF and install it to the oil cooler tube union (inlet oil cooler union).


b.

Install the oil cooler tube union (inlet oil cooler union) to the transaxle case sub-assembly.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 61.INSTALL OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)

a.
C239730

Coat a new O-ring with ATF and install it to the oil cooler tube union (outlet oil cooler union).


b.

Install the oil cooler tube union (outlet oil cooler union) to the transaxle case sub-assembly.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 84540 62.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C135733C19
2.532,0.661 2.722,0.821 0.19,0.16 10 *a 1.701,1.332 2.499,0.754 2.499,0.754 1.699,1.456 false
*a Protrusion


Align the protrusions of the park/neutral position switch.


b.
C136686

Install the park/neutral position switch assembly to the manual valve lever shaft with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Before installing the park/neutral position switch assembly, remove any dirt or rust on the manual valve lever shaft. Be sure to install the park/neutral position switch assembly straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.

·

After installing the park/neutral position switch assembly, confirm that the 2 protrusions on the park/neutral position switch assembly are aligned.




c.
C136685

Install the transmission control shaft lever to the manual valve lever shaft with the washer and nut.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 35104V 63.INSTALL BREATHER PLUG HOSE

a.
C134952C08
2.938,2.396 2.938,2.677 false 2,2.479 2.438,2.479 false 1.646,1.719 2,1.719 false 0.646,0.865 0.802,0.594 0.802,0.594 0.938,0.594 false 1.448,1.656 1.781,1.875 0.333,0.219 10 false *2 1,0.531 1.385,0.76 0.385,0.229 10 false *1 1.781,2.396 2.031,2.594 0.25,0.198 10 false *3 2.865,2.719 3.167,2.948 0.302,0.229 10 false *4
*1 No. 1 Breather Plug (ATM)
*2 Breather Plug Hose
*3 No. 2 Breather Plug (ATM)
*4 O-ring


Coat a new O-ring with ATF and install it to the No. 2 breather plug (ATM).


b.

Install the No. 1 breather plug (ATM) and No. 2 breather plug (ATM) to the breather plug hose.


c.
C190663

Install the breather plug hose to the transaxle case sub-assembly.