Home › Drivetrain › U660E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › 2012.02–2014.05
RM2030EQ _52 Drivetrain _014643 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0074476 DIFFERENTIAL CASE A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41331Q 1.INSTALL DIFFERENTIAL SIDE GEAR

a.
C138528

Coat the 2 differential side gears, 2 No. 1 front differential side gear thrust washers, 2 front differential pinions and 2 front differential pinion thrust washers with ATF and install them to the differential case.


Hide 41342F 2.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C138706

Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.


Hide 3.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

Hide 41342A 4.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C138707

Using a pin punch (3 mm) and hammer, install the front differential pinion shaft straight pin.

NOTICE:

Align the holes, and install the pinion shaft straight pin.



b.
C138711

Using a chisel and hammer, stake the differential case.

NOTICE:

Stake the differential case after adjusting the backlash.



Hide 41311F 5.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C138712
1.75,0.771 2.302,0.615 2.302,0.615 1.865,0.917 false 2.365,0.542 2.906,0.792 0.542,0.25 10 false SST

Using SST and a press, install a new front differential case rear tapered roller bearing to the differential case.

SST
09726-36010  
09950-70010  (09951-07100)

NOTICE:

Do not damage the bearing cage during bearing inner race installation.



b.
C196828
0.885,1.125 0.573,1.396 0.573,1.396 0.74,1.396 false 2.635,1.104 2.563,0.802 2.563,0.802 2.667,0.802 false 0.219,1.323 0.531,1.479 0.313,0.156 10 true SST 2.24,0.719 2.552,0.875 0.313,0.156 10 false SST

Using SST and a hammer, install a new front differential case rear tapered roller bearing outer race to the transaxle case sub-assembly.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the bearing and transaxle case sub-assembly.



Hide 41311E 6.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C196829
0.927,0.552 0.594,0.552 0.594,0.552 0.823,0.833 false 0.594,0.552 0.844,0.698 false 0.271,0.469 0.594,0.635 0.323,0.167 10 false SST

Using SST and a press, install a new front differential case front tapered roller bearing to the differential case.

SST
09710-30012  (09710-04081)
09950-60010  (09951-00480)
09950-70010  (09951-07100)

NOTICE:

Do not damage the bearing cage during bearing inner race installation.



b.

Install the shim to the transaxle housing.


c.
C196830
0.938,1.24 0.625,1.594 0.625,1.594 0.896,1.531 false 2.604,0.698 2.5,0.698 2.5,0.698 2.552,1.073 false 0.281,1.542 0.594,1.708 0.313,0.167 10 false SST 2.188,0.635 2.49,0.802 0.302,0.167 10 false SST

Using SST and a hammer, install a new front differential case front tapered roller bearing outer race to the transaxle housing.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the bearing and transaxle housing.



Hide 7.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.
C205239

Install the differential assembly to the transaxle case sub-assembly.


b.

Clean the contact surfaces of the transaxle case and transaxle housing.


c.
C136447
1.51,1.615 2.49,1.958 2.49,1.958 2.219,1.656 false 1.906,1.646 2.49,1.958 false 2.573,0.938 3.052,1.104 3.052,1.104 2.49,1.417 false 3.063,1.104 2.604,1.146 false 2,0.615 2.896,0.188 2.896,0.188 2.271,0.76 false 1.781,0.531 2.875,0.198 false 1.344,0.469 0.552,0.271 0.552,0.271 0.875,0.74 false 1.156,0.531 0.552,0.271 0.552,0.271 1.021,0.635 false 0.594,1.021 0.229,1.354 0.229,1.354 0.677,1.604 false 0.573,1.396 0.229,1.354 0.229,1.354 0.542,1.198 false 0.875,1.76 1.104,1.969 1.104,1.969 1.302,1.729 false 1.104,1.813 1.104,1.979 false 2.917,0.094 3.052,0.25 0.135,0.156 10 false A 2.5,1.865 2.635,2.021 0.135,0.156 10 false B 0.385,0.156 0.521,0.313 0.135,0.156 10 false A 3.083,1.031 3.219,1.188 0.135,0.156 10 false A 1.063,1.969 1.26,2.156 0.198,0.188 10 false A 0.083,1.271 0.219,1.427 0.135,0.156 10 false A

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
Bolt A : 31 N*m (316 kgf*cm, 23 ft.*lbf)
Bolt B : 23 N*m (234 kgf*cm, 17 ft.*lbf)


d.
C138262
0.841,4.027 1.205,4.212 0.364,0.184 10 SST 1.079,3.308 0.973,4.027 false

Using SST, turn the differential assembly right and left 2 or 3 times to settle the bearings.

SST
09564-33010  


e.

Using SST and a torque wrench, measure the turning torque of the differential side bearing while rotating SST at 10 rpm.

SST
09564-33010  

Turning torque:

1.1 to 1.9 N*m (11 to 19 kgf*cm, 10 to 17 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Shim Thickness: mm (in.)
Thickness Thickness Thickness Thickness
2.000 (0.0787) 2.225 (0.0876) 2.450 (0.0965) 2.675 (0.105)
2.025 (0.0797) 2.250 (0.0886) 2.475 (0.0974) 2.700 (0.106)
2.050 (0.0807) 2.275 (0.0896) 2.500 (0.0984) 2.725 (0.107)
2.075 (0.0817) 2.300 (0.0906) 2.525 (0.0994) 2.750 (0.108)
2.100 (0.0827) 2.325 (0.0915) 2.550 (0.100) 2.775 (0.109)
2.125 (0.0837) 2.350 (0.0925) 2.575 (0.101) 2.800 (0.110)
2.150 (0.0846) 2.375 (0.0935) 2.600 (0.102) 2.825 (0.111)
2.175 (0.0856) 2.400 (0.0945) 2.625 (0.103) 2.850 (0.112)
2.200 (0.0866) 2.425 (0.0955) 2.650 (0.104) 2.875 (0.113)


f.
C287968

Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.


g.
C205239

Remove the differential assembly from the transaxle case sub-assembly.


Hide 41221 8.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
D025215

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

NOTICE:

Do not heat the ring gear to more than 110°C (230°F).



b.

Clean the contact surface of the front differential case.


c.
C138531
1.25,1.427 0.938,0.76 0.938,0.76 1.188,1.5 false 0.833,0.563 1.188,0.771 0.354,0.208 10 false *a
*a Matchmark


Align the matchmarks, and install the front differential ring gear case quickly.

NOTICE:

Do not install the bolts while the ring gear is hot.



d.
C138532

Install and tighten the 12 bolts.

Torque:
120 N*m (1223 kgf*cm, 88 ft.*lbf)

NOTICE:

Tighten the bolts a little at a time in a diagonal sequence.



Hide 31105H 9.INSTALL TRANSAXLE CASE OIL SEAL

a.

Coat the lip of a new oil seal with MP grease.


b.
C196831
1.427,1.313 0.635,2.333 0.635,2.333 1.375,1.542 false 2.156,1.865 2.615,1.865 2.615,1.865 2.542,2.083 false 0.271,2.281 0.583,2.448 0.313,0.167 10 true SST 2.698,1.802 3.167,2.063 0.469,0.26 10 false SST

Using SST and a hammer, install the transaxle case oil seal.

SST
09316-10010  
09950-70010  (09951-07100)

Oil seal driven in depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the transaxle case oil seal is installed in the correct direction.



Hide 31105D 10.INSTALL FRONT TRANSAXLE CASE OIL SEAL

a.
C188707
1,0.781 0.729,0.458 0.729,0.458 0.573,0.458 false 2.406,1.958 2.094,1.958 false 0.219,0.365 0.521,0.521 0.302,0.156 10 false SST 1.771,1.875 2.073,2.031 0.302,0.156 10 false SST

Coat the lip of a new oil seal with MP grease.


b.

Using SST and a hammer, install the front transaxle case oil seal.

SST
09308-14010  

Oil seal driven in depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Check that the front transaxle case oil seal is installed in the correct direction.