Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
48158C
1.INSTALL FRONT LOWER COIL SPRING INSULATOR
|
Positioning Pin |
Install the front lower coil spring insulator to the front shock absorber assembly.
Make sure that the positioning pins on the front lower coil spring insulator are inserted into the holes in the front shock absorber assembly.
48331C
2.INSTALL FRONT SPRING BUMPER
Install the front spring bumper to the front shock absorber assembly.
Face the smaller diameter end of the front spring bumper downward.
48132
3.INSTALL FRONT COIL SPRING
Secure SST in a vise.
| *a | Correct |
| *b | Incorrect |
Attach the arms of SST to the diameter of the front coil spring.
Make sure that the front coil spring is installed so that the distance between the upper and lower arms of SST is at the maximum.
Make sure that the claws of the arms are securely attached.
Using SST, compress the front coil spring.
If the front coil spring bends during compression, immediately stop compression and reinstall SST.
Do not excessively compress the front coil spring so that the coils contact each other.
Do not use an impact wrench. It will damage SST.
Install the front coil spring to the front shock absorber assembly.
Make sure that the end of the front coil spring is positioned in the depression of the front lower coil spring insulator.
48157C
4.INSTALL FRONT UPPER COIL SPRING INSULATOR
|
Outside of the Vehicle |
Install the front upper coil spring insulator as shown in the illustration.
Any misalignment between the front shock absorber lower bracket and the alignment mark must be +/- 5°.
48471C
5.INSTALL FRONT UPPER COIL SPRING SEAT
|
Outside of the Vehicle |
Install the front upper coil spring seat with the mark facing the outside of the vehicle.
Any misalignment between the front shock absorber lower bracket and the alignment mark must be +/- 5°.
48609C
6.INSTALL FRONT SUSPENSION SUPPORT BEARING
| *a | Upper Side |
Install the front suspension support bearing as shown in the illustration.
Do not install the bearing upside down.
48609
7.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY
|
Outside of the Vehicle |
Install the front suspension support sub-assembly as shown in the illustration.
Check that the slot on the piston rod and the slot on the front suspension support sub-assembly are aligned.
Temporarily tighten a new front support to front shock absorber nut.
|
Outside of the Vehicle |
While aligning the stud bolt of the front suspension support sub-assembly and the front shock absorber lower bracket, remove SST from the front coil spring.
When reassembling the front suspension support sub-assembly, ensure that any misalignment between the absorber lower bracket and the stud bolt is within +/- 5°. Use the stud bolt that is closest to the outside of the vehicle.
Do not use an impact wrench. It will damage SST.
8.INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING
Install the front shock absorber with coil spring (upper side) with the 3 nuts.
Install the front shock absorber with coil spring (lower side) to the steering knuckle and insert the 2 bolts and 2 nuts.
While keeping the bolts from rotating, tighten the nuts.
48810
9.INSTALL FRONT STABILIZER LINK ASSEMBLY
Install the front stabilizer link assembly to the front shock absorber assembly with the nut.
If the ball joint turns together with the nut, use a hexagon wrench to hold the stud bolt.
89543
10.INSTALL FRONT SPEED SENSOR
Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt and clamp.
Do not twist the front speed sensor when installing it.
Install the speed sensor harness bracket first and then the front flexible hose.
11.FULLY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT
Fully tighten the front support to front shock absorber nut.
Perform this step only when the front shock absorber with coil spring has been disassembled.
12.INSTALL FRONT WHEEL
13.STABILIZE SUSPENSION
Lower the vehicle and bounce it up and down several times to stabilize the front suspension.
14.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT