Use the same procedure for the LH side and RH side.
The following procedure is for the LH side.
Refer to the illustration to confirm the type of brake used.
| *A | for PBR Made | *B | for ADVICS Made |
| *1 | Front Disc | *2 | Front Disc Brake Cylinder |
1.REMOVE FRONT WHEEL
2.DRAIN BRAKE FLUID
If brake fluid leaks onto any painted surface, immediately wash it off.
47313A
3.SEPARATE FRONT FLEXIBLE HOSE
for PBR Made:
Remove the union bolt and 2 gaskets, and separate the front flexible hose from the disc brake cylinder assembly.
for ADVICS Made:
Remove the union bolt and gasket, and separate the front flexible hose from the disc brake cylinder assembly.
47750
4.REMOVE DISC BRAKE CYLINDER ASSEMBLY
for PBR Made:
| *a | Hold |
| *b | Turn |
Hold the front disc brake cylinder slide pin, and remove the 2 bolts and disc brake cylinder assembly.
for ADVICS Made:
| *a | Hold |
| *b | Turn |
Hold the front disc brake cylinder slide pin, and remove the 2 bolts and disc brake cylinder assembly.
5.REMOVE FRONT DISC BRAKE PAD
for PBR Made:
Remove the 2 front disc brake pads from the front disc brake cylinder mounting.
04465
6.REMOVE FRONT DISC BRAKE PAD KIT
for ADVICS Made:
Remove the 2 anti-squeal springs from the front disc brake pads.
Remove the 2 front disc brake pads with front anti-squeal shim kit from the front disc brake cylinder mounting.
04945
7.REMOVE FRONT ANTI-SQUEAL SHIM KIT
for ADVICS Made:
Remove the front disc brake anti-squeal shim from each front disc brake pad.
Remove the front disc brake pad wear indicator plate from each front disc brake pad.
47716
8.REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE
for PBR Made:
Remove the 2 front disc brake pad support plates from the front disc brake cylinder mounting.
04947
9.REMOVE FRONT DISC BRAKE FITTING KIT
for ADVICS Made:
| *1 | Front No. 1 Disc Brake Pad Support Plate |
| *2 | Front No. 2 Disc Brake Pad Support Plate |
Remove the 2 front No. 1 disc brake pad support plates and 2 front No. 2 disc brake pad support plates from the front disc brake cylinder mounting.
Each front disc brake pad support plate has a different shape. Be sure to put an identification mark on each front disc brake pad support plate so that it can be reinstalled to its original position.
47715A
10.REMOVE FRONT DISC BRAKE CYLINDER SLIDE PIN
for PBR Made:
Remove the 2 front disc brake cylinder slide pins with the front disc brake bushing dust boot from each front disc brake cylinder mounting.
for ADVICS Made:
Remove the front disc brake cylinder slide pin from the front disc brake cylinder mounting.
47715D
11.REMOVE FRONT NO. 2 DISC BRAKE CYLINDER SLIDE PIN
for ADVICS Made:
Remove the front No. 2 disc brake cylinder slide pin from the front disc brake cylinder mounting.
47769
12.REMOVE FRONT DISC BRAKE CYLINDER SLIDE BUSHING
for ADVICS Made:
| *1 | Vinyl Tape |
Using a screwdriver with its tip wrapped with vinyl tape, remove the front disc brake cylinder slide bushing from the front No. 2 disc brake cylinder slide pin.
Do not damage the front No. 2 disc brake cylinder slide pin.
47775
13.REMOVE FRONT DISC BRAKE BUSHING DUST BOOT
for PBR Made:
Remove the front disc brake bushing dust boot from the front disc brake cylinder slide pin.
47722
14.REMOVE FRONT DISC BRAKE CYLINDER MOUNTING
for PBR Made:
Remove the 2 bolts and front disc brake cylinder mounting from the steering knuckle.
for ADVICS Made:
Remove the 2 bolts and front disc brake cylinder mounting from the steering knuckle.
47775
15.REMOVE FRONT DISC BRAKE BUSHING DUST BOOT
for ADVICS Made:
Secure the front disc brake cylinder mounting in a vise.
Using a screwdriver and a plastic hammer, remove the 2 front disc brake bushing dust boots.
43512
16.REMOVE FRONT DISC
| *a | Matchmark |
Put matchmarks on the front disc and the front axle hub.
Remove the front disc.