Home › Brake › BRAKE (FRONT) › FRONT BRAKE FLEXIBLE HOSE › 2012.02–2015.04
RM2030EQ _54 Brake _014652 BRAKE (FRONT) _0074519 FRONT BRAKE FLEXIBLE HOSE A

BRAKE (FRONT)  FRONT BRAKE FLEXIBLE HOSE  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Because the left and right hoses are not interchangeable, verify the part number when installing the flexible hoses.

·

If the hoses are to be reused, connect them after checking the identification marks placed when each hose was disconnected.



HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 47313A 1.INSTALL FRONT FLEXIBLE HOSE

a.
C238495C07
2.023,0.979 2.175,1.122 0.152,0.143 10 *1 1.845,1.054 2.009,1.054 false
*1 Clip


Install a new clip to the front flexible hose.

NOTICE:

Install the clip as far as it will go.



b.

Using a union nut wrench, connect the brake line to the front flexible hose while holding the flexible hose with a wrench.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting points.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




c.
C239561C02
1.135,0.802 0.469,0.344 0.469,0.344 1.198,0.677 true 1.156,0.917 1.021,1.042 1.021,1.042 0.781,1.042 true 1.479,0.406 1.563,0.24 1.563,0.24 1.688,0.24 true 1.708,0.146 1.938,0.479 0.229,0.333 10 *1 0.615,0.969 0.906,1.24 0.292,0.271 10 *2 0.281,0.229 0.583,0.604 0.302,0.375 10 *3
*1 Front Speed Sensor Clamp
*2 Front Flexible Hose
*3 Claw


Install the front speed sensor clamp and front flexible hose to the shock absorber bracket with the bolt.

Torque:
19 N*m (192 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not twist the wire harness for the front speed sensor when installing it.

·

Securely set the 2 claws of the front speed sensor clamp to the shock absorber bracket.

·

A bolt tightens the brake flexible hose and front speed sensor together. Make sure that the front flexible hose is positioned over the front speed sensor.




d.

for PBR Made:

i.
C246328C01
2.947,0.953 3.114,1.1 0.166,0.147 10 *a 1.561,1.033 2.91,1.033 false
*a Lock Hole


Connect the front flexible hose to the front disc brake cylinder assembly with the union bolt and 2 new gaskets.

Torque:
30 N*m (305 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the flexible hose lock securely into the lock hole in the front disc brake cylinder.




e.

for ADVICS Made:

i.
C238481C01
2.021,0.76 2.844,0.76 true 2.875,0.677 3.188,0.833 0.313,0.156 10 *a
*a Lock Hole


Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
30 N*m (305 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the flexible hose lock securely into the lock hole in the front disc brake cylinder.




Hide 3.INSTALL FRONT WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)