Use the same procedure for the LH side and RH side.
The following procedure is for the LH side.
Refer to the illustration to confirm the type of brake used.
| *A | for PBR Made | *B | for ADVICS Made |
| *1 | Rear Disc | - | - |
| *a | 190 to 191 mm (7.48 to 7.51 in.) | *b | 170 to 171 mm (6.69 to 6.73 in.) |
1.REMOVE REAR WHEEL
2.DRAIN BRAKE FLUID
If brake fluid leaks onto any painted surface, immediately wash it off.
47319F
3.SEPARATE REAR FLEXIBLE HOSE
for PBR Made:
Remove the union bolt and 2 gaskets, and separate the rear flexible hose from the rear disc brake cylinder assembly.
for ADVICS Made:
Remove the union bolt and gasket, and separate the rear flexible hose from the rear disc brake cylinder assembly.
47850
4.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY
for PBR Made:
| *a | Hold |
| *b | Turn |
Hold the rear disc brake cylinder slide pin, and remove the 2 bolts and rear disc brake cylinder assembly.
for ADVICS Made:
| *a | Hold |
| *b | Turn |
Hold the rear disc brake cylinder slide pin, and remove the 2 bolts and rear disc brake cylinder assembly.
04466
5.REMOVE REAR DISC BRAKE PAD
for PBR Made:
Remove the 2 rear disc brake pads from the disc brake cylinder mounting.
for ADVICS Made:
Remove the 2 rear disc brake pads with rear disc brake anti-squeal shim kit from the disc brake cylinder mounting.
04946
6.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT
for ADVICS Made:
Remove the rear disc brake anti-squeal shim from each rear disc brake pad.
Remove the rear disc brake pad wear indicator plate from each rear disc brake pad.
47716A
7.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE
for ADVICS Made:
Remove the 2 rear disc brake pad support plates from the disc brake cylinder mounting.
47715C
8.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN
for PBR Made:
Remove the 2 rear disc brake cylinder slide pins with rear disc brake bushing dust boot from the disc brake cylinder mounting.
47814
9.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN (for Upper Side)
for ADVICS Made:
Remove the rear disc brake cylinder slide pin from the disc brake cylinder mounting.
47814
10.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN (for Lower Side)
for ADVICS Made:
Remove the rear disc brake cylinder slide pin from the disc brake cylinder mounting.
11.REMOVE REAR DISC BRAKE CYLINDER SLIDE BUSHING
for ADVICS Made:
| *1 | Vinyl Tape |
Using a screwdriver with its tip wrapped with vinyl tape, remove the rear disc brake cylinder slide bushing from the rear disc brake cylinder slide pin.
Do not damage the rear disc brake cylinder slide pin.
47775D
12.REMOVE REAR DISC BRAKE BUSHING DUST BOOT
for PBR Made:
Remove the rear disc brake bushing dust boot from each rear disc brake cylinder slide pin.
for ADVICS Made:
Remove the 2 rear disc brake bushing dust boots from the disc brake cylinder mounting.
47722A
13.REMOVE DISC BRAKE CYLINDER MOUNTING
for PBR Made:
Remove the 2 bolts and disc brake cylinder mounting.
for ADVICS Made:
Remove the 2 bolts and disc brake cylinder mounting.
42491
14.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG
Remove the parking brake shoe adjusting hole plug.
42431
15.REMOVE REAR DISC
| *a | Matchmark |
Put matchmarks on the rear disc and the rear axle hub.
Release the parking brake and remove the rear disc.
If the disc cannot be removed easily, use a screwdriver to turn the shoe adjuster as shown in the illustration in order to contract the parking brake shoes.