Home › Steering › STEERING COLUMN › STEERING PAD SWITCH(for 4 Spoke) › 2012.02–2015.04
RM2030EQ _55 Steering _014656 STEERING COLUMN _0074534 STEERING PAD SWITCH(for 4 Spoke) G

STEERING COLUMN  STEERING PAD SWITCH(for 4 Spoke)  INSPECTION  


PROCEDURE

Hide 84250A 1.INSPECT STEERING PAD SWITCH ASSEMBLY (for Audio and Visual System (for Radio Receiver Type))

a.

Measure the resistance according to the value(s) in the table below.

E244528
1.881,1.57 2.035,1.728 0.154,0.158 10 *b 1.091,2.509 1.244,2.667 0.154,0.158 10 *d 3.703,1.262 4.007,1.420 0.304,0.158 10 EAU 4.042,0.955 3.89,1.25 false 4.106,1.262 4.398,1.420 0.292,0.158 10 AU2 4.245,0.955 4.245,1.25 false 4.495,1.262 4.786,1.420 0.292,0.158 10 AU1 4.347,0.955 4.597,1.25 false 1.676,2.578 1.253,2.578 false 2.705,2.229 2.859,2.387 0.154,0.158 10 *e 2.188,2.578 2.681,2.297 false 1.945,2.334 1.945,1.735 false 5.366,1.598 5.520,1.756 0.154,0.158 10 *g 5.132,2.348 5.398,1.763 false 5.366,3.41 5.520,3.569 0.154,0.158 10 *h 5.132,2.803 5.398,3.388 false 1.573,3.271 1.727,3.429 0.154,0.158 10 *c 1.945,2.817 1.679,3.248 false 2.985,2.954 3.139,3.112 0.154,0.158 10 *f 2.398,3.029 2.961,3.029 false 0.144,0.113 0.361,0.271 0.217,0.158 10 *a 1.808,3.891 1.962,4.049 0.154,0.158 10 *i 2.349,3.48 1.916,3.911 false 1.455,0.589 1.609,0.748 0.154,0.158 10 *j 2.04,0.658 1.617,0.658 false 3.514,0.149 3.827,0.307 0.313,0.158 10 +DP 3.512,0.391 3.742,0.549 0.230,0.158 10 HO 4.406,0.264 4.682,0.423 0.276,0.158 10 -DP 3.92,0.786 3.727,0.533 false 4.031,0.776 3.938,0.228 3.938,0.228 3.821,0.228 false 4.157,0.788 4.262,0.324 4.262,0.324 4.374,0.324 false
*a Component without harness connected
(Steering Pad Switch Assembly)
*b Volume+
*c Volume- *d Seek-
*e Seek+ *f MODE/HOLD
*g Off hook *h On hook
*i DISP *j Terminal-A


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (HO) - Terminal-A Always Below 1 Ω
2 (+DP) - 3 (-DP) No switch pushed 95 to 105 kΩ
DISP switch pushed Below 2.5 Ω
11 (AU1) - 8 (EAU) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
10 (AU2) - 8 (EAU) No switch pushed 95 to 105 kΩ
MODE/HOLD switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 950 to 1050 Ω


HINT:

If the result is not as specified, replace the steering pad switch assembly.



b.

Check the illumination.

E244529
0.129,0.113 0.631,0.262 0.502,0.149 10 *a 4.691,1.042 4.986,1.191 0.295,0.149 10 IL+2 4.349,0.83 4.652,1.074 false 3.744,0.2 4.001,0.349 0.258,0.149 10 -DP 4.126,0.812 3.891,0.353 false
*a Component without harness connected
(Steering Pad Switch Assembly)
- -


i.

Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.


ii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


HINT:

If the result is not as specified, replace the steering pad switch assembly.




Hide 84250A 2.INSPECT STEERING PAD SWITCH ASSEMBLY (except Audio and Visual System (for Radio Receiver Type))

a.

Measure the resistance according to the value(s) in the table below.

E225611
0.148,0.125 0.301,0.283 0.154,0.158 10 *a 1.431,1.57 1.584,1.729 0.154,0.158 10 *b 1.556,0.595 1.709,0.754 0.154,0.158 10 *o 1.767,1.57 1.920,1.729 0.154,0.158 10 *f 1.103,2.523 1.256,2.681 0.154,0.158 10 *h 3.837,1.241 4.141,1.400 0.304,0.158 10 EAU 3.7,0.157 4.012,0.315 0.313,0.158 10 +DP 3.698,0.399 3.927,0.557 0.230,0.158 10 HO 4.019,1.55 4.323,1.708 0.304,0.158 10 AU3 4.319,0.968 4.196,1.53 false 4.218,0.968 4.038,1.221 false 4.615,1.241 4.919,1.400 0.304,0.158 10 AU1 4.591,0.273 4.868,0.431 0.276,0.158 10 -DP 4.432,1.55 4.736,1.708 0.304,0.158 10 AU2 4.422,0.968 4.545,1.53 false 4.523,0.968 4.703,1.221 false 1.688,2.592 1.265,2.592 false 5.949,2.523 6.663,2.681 0.714,0.158 10 *m (*A) 5.502,2.592 5.925,2.592 false 2.857,2.243 3.011,2.401 0.154,0.158 10 *i 2.2,2.592 2.833,2.312 false 2.857,2.912 3.011,3.070 0.154,0.158 10 *j 2.018,2.625 2.833,2.985 false 2.857,3.276 3.011,3.434 0.154,0.158 10 *e 2.324,3.124 2.833,3.35 false 1.943,2.334 1.831,1.736 false 1.727,2.152 1.537,1.736 false 2.198,1.57 2.351,1.729 0.154,0.158 10 *d 2.047,2.136 2.229,1.736 false 5.521,1.598 5.674,1.757 0.154,0.158 10 *k 5.294,2.331 5.552,1.764 false 5.521,3.425 5.674,3.583 0.154,0.158 10 *l 5.291,2.827 5.552,3.402 false 1.431,3.495 1.584,3.653 0.154,0.158 10 *c 1.852,4.002 2.064,4.160 0.212,0.158 10 *n 1.879,3.495 2.033,3.653 0.154,0.158 10 *g 1.943,2.845 1.943,3.472 false 1.79,3.062 1.537,3.472 false 2.223,0.663 1.713,0.663 false 2.362,3.554 1.933,3.984 false 4.099,0.793 3.906,0.54 false 4.217,0.785 4.124,0.236 4.124,0.236 4.006,0.236 false 4.342,0.797 4.447,0.333 4.447,0.333 4.559,0.333 false
*A w/ Voice Switch of Steering Pad Switch Assembly - -
*a Component without harness connected
(Steering Pad Switch Assembly)
*b Volume+
*c Volume- *d Back
*e MODE/HOLD *f Up
*g Down *h Left
*i Right *j Enter
*k Off hook *l On hook
*m Voice *n DISP
*o Terminal-A - -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (HO) - Terminal-A Always Below 1 Ω
2 (+DP) - 3 (-DP) No switch pushed 95 to 105 kΩ
DISP switch pushed Below 2.5 Ω
11 (AU1) - 8 (EAU) No switch pushed 95 to 105 kΩ
Up switch pushed Below 2.5 Ω
Down switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
10 (AU2) - 8 (EAU) No switch pushed 95 to 105 kΩ
MODE/HOLD switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 950 to 1050 Ω
Voice switch pushed*1 2955 to 3265 Ω
9 (AU3) - 8 (EAU) No switch pushed 95 to 105 kΩ
Enter switch pushed Below 2.5 Ω
Back switch pushed 313 to 345 Ω
Right switch pushed 950 to 1050 Ω
Left switch pushed 2955 to 3265 Ω


*1: w/ Voice Switch of Steering Pad Switch Assembly

HINT:

If the result is not as specified, replace the steering pad switch assembly.



b.

Check the illumination.

E230752
0.077,0.046 0.256,0.213 0.179,0.168 10 *a 3.732,0.169 3.999,0.337 0.267,0.168 10 -DP 4.9,1.145 5.211,1.313 0.311,0.168 10 IL+2 4.332,0.815 3.95,0.312 false 4.535,0.817 4.881,1.162 false
*a Component without harness connected
(Steering Pad Switch Assembly)
- -


i.

Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.


ii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


HINT:

If the result is not as specified, replace the steering pad switch assembly.