Home › Audio / Visual / Telematics › AUDIO / VIDEO › NOISE FILTER
RM2030EQ _56 Audio / Visual / Telematics _014658 AUDIO / VIDEO _0074546 NOISE FILTER G

AUDIO / VIDEO  NOISE FILTER  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 86011R 1.INSPECT RADIO SETTING CONDENSER (for High Mounted Stop Light)

a.

With the radio setting condenser installed, check that there is no looseness or other abnormalities.


b.

Remove the bolt.


c.

Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.


d.
E211797
2.406,1.729 1.927,1.729 false 1.917,0.917 2.448,1.177 false 1.927,0.76 2.406,0.542 false 2.49,1.146 2.792,1.365 0.302,0.219 10 false 2 2.458,1.656 2.76,1.896 0.302,0.24 10 false 3 2.458,0.458 2.729,0.667 0.271,0.208 10 false 1 0.115,0.073 0.479,0.323 0.365,0.25 10 false *a
*a Radio Setting Condenser


Measure the resistance and voltage of the radio setting condenser according to the value(s) in the table below.

NOTICE:

Before measuring the resistance and voltage, be sure to use insulated probes to avoid a short circuit between the tester terminal and bracket.


Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2
·

Ignition switch off

·

High mounted stop light off

·

Window defogger off

·

Luggage compartment room light off


10 kΩ or higher
1 - 3 10 kΩ or higher
1 - Body ground Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
2 - Body ground
·

Ignition switch ON

·

High mounted stop light off

·

Window defogger off

·

Luggage compartment room light off


Below 1 V
3 - Body ground Below 1 V
2 - Body ground
·

Ignition switch ON

·

High mounted stop light on

·

Window defogger on

·

Luggage compartment room light on


11 to 14 V
3 - Body ground 11 to 14 V



Hide 86011Q 2.INSPECT RADIO SETTING CONDENSER (for Window Defogger)

a.

With the radio setting condenser installed, check that there is no looseness or other abnormalities.


b.

Remove the bolt.


c.

Disengage the 2 clamps and disconnect the radio setting condenser with wire harness from the vehicle body.


d.
E230106
1.948,0.573 2.417,0.573 false 2.083,1.583 2.542,1.427 false 1.344,1.594 0.813,1.427 false 2.458,0.479 2.698,0.698 0.24,0.219 10 3 2.573,1.323 2.833,1.563 0.26,0.24 10 2 0.698,1.313 1,1.563 0.302,0.25 10 1 0.094,0.083 0.542,0.396 0.448,0.313 10 *a
*a Radio Setting Condenser


Measure the resistance and voltage of the radio setting condenser according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (+B) - 2 (GND)
·

Ignition switch off

·

High mounted stop light off

·

Window defogger off

·

Luggage compartment room light off


10 kΩ or higher
3 - Body ground Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
1 - Body ground
·

Ignition switch ON

·

High mounted stop light off

·

Window defogger off

·

Luggage compartment room light off


Below 1 V
1 - Body ground
·

Ignition switch ON

·

High mounted stop light on

·

Window defogger on

·

Luggage compartment room light on


11 to 14 V